Hi Paul
I finish to renovate my new house and ready to go back on my project.
I will stay with p port intake and install turbo but i want to built my
own
drive with ford diezel trans 5R110W planet gear system.
the gear system is bigger then the E40D WITH RATIO OF 2.48.-6 pinion
planet
system Drum size 5"+
I look on the Slauson catalogue but i found a better price on EBAY
I intend to cruise at 6200 rpm approx and i would like to know the HP at
this
rpm for rx-8 pport and turbo.
i will also appreciate your comments
Jean Prudhomme
I think that gear set is overkill and too heavy.
Several people have used the A4OD set with three rotors.
One with a turbo 3 rotor. The ratio is not as good
as it is only 2.48 rather than 2.85.
Send me a dwg of the rest of the gear box.
The HP you get will depend on the boost. The fuel
burn will determine that at cruise. Figure a half pound
of fuel burned for every HP you choose. Fuel weighs
about 6.25 pounds per gallon.
P-port 2 rotors have been easily boosted to 400 HP
or more. Obviously you don't want to burn that much
fuel at cruise.
Paul Lamar
--
I just order parts from Slauson on E40D, it should be here next week.Will
folow with gearbox dwgs
Jean Prudhomme
Jean Prudhomme, I just thought I would share an idea on a part for your
CS Psru. The attached pictures are various four wheel drive front hubs.
This
is a bolt on hollow spindle with a flanged wheel hub, The hub has internal
splines for the drive. The output from the planetary would be splined on
both ends. Early models from the 1970's are longer with widely spaced
bearings, Later models like the Dodge Dakota are more compact. This hub
would bolt on to the front of the gearbox providing a larger diameter
attachment to counter bending loads and gyroscopic loads. The spindles are
pilot bore mounted and have three to five attachment bolts. The Dakota
shown
is an after market part with a full circular flange so you could have
seven
attachment bolts. You would be looking for a 1/2 ton truck with a six bolt
wheel. The 8 bolt wheel parts are heavier and would also require an
additional adapter plate.
For my 4 rotor I have approximately 775 pounds of continuous thrust
load which should not be a problem bearing wise, and on the truck this
part
sees 1500 pounds of static radial load. This should be workable with a 60
pound constant speed prop.
The new part price for the complete hub is around $90 on Ebay.
george grimes
What does that stuff weigh George? Would it not be better to spread
the bearings and use light weight needles? One would have to machine
these things to match the SAE prop flange. Do you have a dwg on the
truck front wheel bolt pattern? These things are designed for high
radial (vertical) loads and not optimized for gyro bending loads.
The low technical risk approach is to just copy the front
of a Lycoming crankcase and crank shaft. This has the advantage
of getting the high pressure oil pitch control oil into the prop
the same way Lycoming does it. One might be able to buy a cracked
Lycoming shaft and cut off most of it. The shaft seals are critical.
One pays a huge weight penalty using a 50 pounds metal constant speed
prop anyway as it adds to the shaft strength and bearing requirements.
The total weight is probably about 60 to 70 pounds. Governors also
cost close to $1000. On the other hand a fixed pitch composite
prop might be 20 pounds.
That opens up another approach to think about and that is the
fact that experimental's have a better power to weight ratio than a lot
of certified aircraft so there is less need for a low pitch prop on take
off.
Just choose a good fixed pitch composite cruise prop and let the take off
performance be what it is. Runways are generally much longer than what
experimental's need.
--------------------------------------------------------------
Here is another way of attaching a flange to a light weight hollow
tubing shaft using needle bearings. Old Lou Ross largely got it
right except for the torque mitigator. Now that Jeff has an NC
lathe this becomes viable if he wanted to make psru's. Nothing
is selling right at the moment so it might have to wait till
the economy recovers if ever.
It will take a complete about face in Washington :)
Paul Lamar
--
Paul, I would expect the 4X4 hub to be about 16 pounds but haven't got one
to weigh. As for remachining, automotive wheels fit over a pilot as shown in
the picture of the hub. If too large it would need turned smaller. If too
small a sleeve would be pressed on to bring it up to the required size..
This is not a perfect approach, however for those of us who don't have
access to large CNC equipment or can not afford to hire it out adding 5
pounds of weight might be an acceptable tradeoff. It is just a suggestion.
This type of design is the only way large equipment like 18 wheelers is
designed including the wheels on the trailer where there is no drive.Using a
hub with a six lug wheel would facilitate drilling the attach bolts between
the existing holes as is done with the cruuent PSRU which is also a car
axle. Spreading the bearings would be better for gyroscopic loads but
heavier and require more length. This weight penalty is only justified if
a hyd constant speed prop is necessary. Otherwise the Tracy Croook PSRU is
well flight tested, affordable, and has good support from Tracy. No use
arguing with success.
I just dont think a fixed pitch will work on my
airframe. The schneider cup race planes were on floats possibly due to a 2
mile takeoff distance with fixed pitch props. The sim is predicting 326 MPH
top speed with a four rotor at max gross weight. My weight and ballance
spread sheet lists the prop at 60 pounds and the PSRU at 65 pounds so I can
afford the weight of a constant speed prop.
I have a timken catalog on my hard drive but couldn't find a page
showing what the dimensions in your attachment reffer to.Usually when I spec
the drawn housing needle bearings the catalog bore is for running the
bearing directly on the shaft. Using the inner ring ( IR-273216 ) would
reduce the diameter of the shafting. Sizing up the bearing so that the inner
ring bore corresponds to your sketch should be fine since the shown RPM is
well over what we need and is fairly related to diameter. IMHO running the
rollers on the shaft even induction hardened would result in brinelling of
the shaft. These uncaged bearings also have high friction losses because the
circumfrence of the rollers are running in opposite directions where they
touch tangentially.
There are quite a few Lycoming engines not rated for constant
speed props and they all seem to come with RPM ranges they can not operate
at continuously. It would seem that we are talking about discarding the very
wide journal bearing used on the Lycoming front shaft. Replacing the one
wide bearing with two spaced needle bearings leaves the area between them
unsupported. A FEA analysis should include checking bending distortions in
this area. The angular misalignment (slope in catalog speak) is listed as
"none" for needle bearings. There is now a free FEA program (calculix) you
can download.
Looking at attachment P1100513 it appears that you propose cutting
off the splined hub on the planetary carrier. The back side of this hub is
the thrust face for the sun gear. With the hub removed it looks to me like
the sun gear would be running against the screw heads. It is possible that
the rotation direction is such that the sun gear thrust is away from the
planetary carrier which avoids the screw heads. But with the rear planetary
not being used the sun gear (common to the two planetarys) has nothing to
resist the force trying to back it out of the carrier.
I don't see the pilot for the prop on the flange, Possibly the
flange could be moved forward extending the counterbore in front of the
attach screws to the shaft. Then a pilot with the prop diameter on one end
and the counterbore diameter on the other end could be press fit into the
flange and "O" ring sealed. Also I might suggest that the part in
tube-psru-5c could have a bulkhead left in it just in front of the planatary
flange attachment. It would be thick enough to rout the prop oil lines into.
From the bulkhead two steel tubes would go out to the pilot flange sealed on
both ends with "O" rings.
I am not going to use a metal prop. I have run a list of prop
airfoils through the simulator (clark-y, hartzel, hamilton, MT) which are
amazingly similar in performance. MY choice however is the Boeing high
subsonic series. If I have to build the prop I can CNC the molds with my
gantry router and use carbon fiber with vacuum infusion. My first stop will
however be to Sensenich in Florida to see if they will sell me four of their
composite ground adjustable blades. If the truck hub works out they have an
antilock break sensor built into the part which I would adapt for the
governor signal.A DO3 size hyd valve with a proportional spool would feed
the prop.
george grimes
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.