Subject: Renesis Coils stand alone rotary ignition.
From: Rotary Engine
Date: 10/12/2010, 6:06 PM
To: AAA Put this in the To box

Does anybody know how the wiring goes for the four individual coils on
the
Renesis engine. It is one of the test engines bought up by that
Australian a
couple of years ago.
There are three wires (black, black with white stripe and the third wire
is
a different color for each coil). The coils black wires are all wired
together with a 0.47uf capacitor attached at the splice, and  the
black/white wires are also wired together but the wire coming out was
cut
off at the splice. -- Karibian

Black with white stripe is 12 volt power
The third wires are triggers from the computer
as follows.

G is green front rotor leading (lower) plug.
W is white front rotor trailing (top) plug.
Y/G yellow / green is back rotor leading plug.
B/O blue /orange is back rotor trailing plug.


Black is ground.

Paul Lamar


   Keep the cap on the ground wires, too.

   Kenny


   These are inductive coils and they normally require a computer.
   Inductive coils are turned on for a period of time and then
   they fire when the current is suddenly turned off. This off time
   is called dwell. If the dwell is too long the coils over heat.
   If too short you don't get full spark energy.

   The breakthrough on how to make this stand alone and work without
   a computer just occurred to me. The trick is to slot the trigger
   wheel and use a  IR photo transistor, an IR emitter LED and FET switch
   instead of a magnetic pickup or Hall Effect sensor. These devices
   put out a single narrow pulse. Not what we need.

   When the IR photo transistor sees the infra red emissions from the
   IR LED it turns the coil current on using an high voltage FET solid
  state
   switch. I used something like this for years on my computerized
   road test equipment and it is very reliable and durable.

   It will work with just about any stock inductive plug on coil system
   including the Corvette GM coils. The length of the slot controls the
   dwell time. The end of the slot controls when the coil fires.

   I have been thinking about this problem ever since the stand alone
   coil on plug systems first appeared. How do we get rid of
   the computer?

   If you want to fire the leading and trailing plugs at different
   times you can use four slots with four photo TX's and four
   LED's other wise each photo TX fires both leading and trailing
   plug coils at the same time.

   Now some of you electronic types might say "why not just
   use a 555 one shot with a fixed pulse width to turn on
   the current in the coil for a fixed period of time triggered
   by a magnetic sensor or Hall Effect "?

   The problem with that is the spark timing will vary with RPM.
   You want the plugs to fire at 22 degrees TDC over a wide range of
   RPM's so that approach will not work.

   Basically this thing works like distributer points.

   Paul Lamar



Paul,

Will this also work on a 2nd gen?

Any plans to make trigger wheels?

Can the trigger work with an EFI also?

Joe Berki
Limo EZ

It will work on any rotary engine. 2 rotor or 3 rotor.
(3 slots)

Here is a 50 cent improvement. A CMOS 4050 all six gates connected
in parallel drives the FET very reliably.

Paul Lamar



  Paul,

  Would it be better to mount the trigger wheel and the associated
electronic
  components off of the flexplate area assuming one uses Tracy"s PSRU?  When
  you loose a belt it could take out trigger wheel components.  Just a
  thought.

  Joe Berki
  Limo EZ

  Yes that would work. BTW Joe I get a lot of bounces
  from your email address. It would better if you got a new
  email address.

  ---------------------------------------------------

  Here is what the cover would look like. It is about 4.25 inches
  in over all diameter. The front cover, the rear cover and the
  trigger wheel are made from 1/16th fiberglass. The small amount circuitry
  needed is etched on the front cover. The spindle will work
  with several types of ignition systems.

  Is anybody interested in buying one of these?  I'll have some made.

  It will work well with a Holley 2 barrel carb for low overall all
  P-port engine cost and simplicity.

  Paul Lamar



Paul,

Maybe this design could be incorporated into the flexplate.  Depending on
Renesis, 20b, 13b, 2nd gen or 3rd gen the one common denominator is a
flexplate and ususally Tracy's gearbox.  The front of the engine could
differ vastly depending on front covers, pulleys, water pumps and space
constraints.  I would also like to see an output for fuel injection timing.

Joe Berki

Could be. Depending on clearing Tracy's torque mitigator.
It don't look good. Maybe a 12 inch diameter disc placed
under the heads of the four torque mitigator bolts.

Paul Lamar

I set up the GM coil on the bench and here is a movie of it working
at 6000 RPM with only 4 volts. Amazing. Current draw is about
1 amp. The FET or switching transistor is indeed inside the coil
making the external electronics very simple.

Dwell time 5 ms. I'll do a little more R&D by reducing the dwell
time.

I kept the file size short so put it in a continuous loop.

Let me know if you want a different video format.

I imagine the RX8 coils work in a similar manner
as they are both made by Nippon Denso.

This is real easy to set up on a bench if you
have a pulse generator.

I notice a lot of guys racing rotaries in the SCCA are
still using the old fashion distributer. Unfortunately they
stick up a bit too far to use in an airplane.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.