I have always been fascinated with the idea of building
a cheap airplane out of the lowest cost composite materials
possible. Back in 1965 when I worked for chaparral cars I did a
study on the lightest material to use for a race car body.
I settled on 1/4 inch PVC foam with one layer of 4 oz glass
cloth on either side. It was much lighter and stiffer per
square foot than .032 aluminum.
http://www.jmsonline.net/glass-fabric-4oz50-x-10.htm?source=googleps
We built the body of the chaparral 2F
out of that in a vacuum bagged female mold. The body was very
strong and so light the paint shop doubled the weight.
The car was capable of well over 200 MPH at some tracks like
LeMans so the body was plenty strong enough.
Race car bodies and airplanes have at least one unique thing in
common. The body panels and wing panels are subject to high pressures
distributed over the surface. The structure must be strong enough
to resists these kinds of loads. Sandwich panels are ideal.
At 200 MPH the worst case scenario on a wing is dynamic pressure or
about 100 pounds per square foot.
In other words the lift coefficient is one. If the ribs are one foot
apart the center of the panel should not deflect excessively or fail
with a distributed load of 8.33 pounds every inch. This is easy
to set up a test panel and check for failure and deflection.
It may be that rib spacing of two feet or more is acceptable depending
the core thickness. Thicker foam cores add little weight while
allowing greater rib spacing. In other words fewer ribs with less
fabrication work.
Female compound curve molds are very expensive and time consuming
but fast airplanes can be built out of flat panels and simple curve
parts. The Vans RV series are good examples.
A cured sandwich panel is very strong and stiff but it is difficult at
best to curve it to fit the top of a wing for example.
The question is: how do we build a wing out of pre-curred flat panels?
I think I have the answer. What we need is foam screws to screw
the flat panels to the curved wing rib edges until the epoxy sets
up. Here is a cheap, super light weight foam screw called a dry
wall anchor obtainable in any hardware store. It is used to hang
rather heavy objects on a dry wall.
The next trick to to lay up half the sandwich panel on a flat
surface so only one side is curred. The other side is raw foam.
This then can be bent, raw foam up, to cover the top of the ribs
and screwed to the one inch thick foam ribs with foam screws while
the epoxy glue cures.
We then lay up a single layer sheet of glass fiber on a smooth
flat surface and let it cure. It will be very flexible when
it is curred so we can bend it to fit over the raw foam
already bonded to the ribs shiny side up. Weights placed
over the rib areas can be used to hold it down while it
cures. These weights can be made from long skinny sand
filled cloth bags. In some cases bungee cord can be used
to make the leading edges conform. In certain extreme cases
one could use foam screws.
The whole idea here is to cut the cost and time needed
to build an airplane and take advantage of the low cost
rotary engine.
What do you guys think of this idea?
Paul Lamar
Paul,
As a possible alternative to foam, look at 'nida-core'
http://nida-core.com/english/
It's used extensively in the boat-building business. Lot of
advantages over foam. I've got an unused box sitting in my shop,
I'm going to prototype a belly cargo pod with it.
The boat-builder / repairman who put my on to it had the same
opinion as you, 1 layup on each side is plenty strong. Also,
this stuff is impervious to fuel / acetone / saltwater, etc.,
unlike foam.
-Kenny A.
I don't know what that is but if it is open cell like honeycomb
it is hard to bond on a skin as the epoxy runs down and fills
the space between the walls of the honeycomb. That is normally
handled by using prepreg in a female mold. If you attempted
to bond on a pre curred skin you would have to add a layer
of prepreg which would unnecessarily add to the weight.
The devil is always in the details :)
Is it end grain balsa?
What is the density in pounds per cubic foot what ever it is?
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.