I have always been fascinated with the idea of building
a cheap airplane out of the lowest cost composite materials
possible. Back in 1965 when I worked for chaparral cars I did a
study on the lightest material to use for a race car body.
I settled on 1/4 inch PVC foam with one layer of 4 oz glass
cloth on either side. It was much lighter and stiffer per
square foot than .032 aluminum.
http://www.jmsonline.net/glass-fabric-4oz50-x-10.htm?source=googleps
We built the body of the chaparral 2F
out of that in a vacuum bagged female mold. The body was very
strong and so light the paint shop doubled the weight.
The car was capable of well over 200 MPH at some tracks like
LeMans so the body was plenty strong enough.
Race car bodies and airplanes have at least one unique thing in
common. The body panels and wing panels are subject to high pressures
distributed over the surface. The structure must be strong enough
to resists these kinds of loads. Sandwich panels are ideal.
At 200 MPH the worst case scenario on a wing is dynamic pressure or
about 100 pounds per square foot.
In other words the lift coefficient is one. If the ribs are one foot
apart the center of the panel should not deflect excessively or fail
with a distributed load of 8.33 pounds every inch. This is easy
to set up a test panel and check for failure and deflection.
It may be that rib spacing of two feet or more is acceptable depending
the core thickness. Thicker foam cores add little weight while
allowing greater rib spacing. In other words fewer ribs with less
fabrication work.
Female compound curve molds are very expensive and time consuming
but fast airplanes can be built out of flat panels and simple curve
parts. The Vans RV series are good examples.
A cured sandwich panel is very strong and stiff but it is difficult at
best to curve it to fit the top of a wing for example.
The question is: how do we build a wing out of pre-curred flat panels?
I think I have the answer. What we need is foam screws to screw
the flat panels to the curved wing rib edges until the epoxy sets
up. Here is a cheap, super light weight foam screw called a dry
wall anchor obtainable in any hardware store. It is used to hang
rather heavy objects on a dry wall.
The next trick to to lay up half the sandwich panel on a flat
surface so only one side is curred. The other side is raw foam.
This then can be bent, raw foam up, to cover the top of the ribs
and screwed to the one inch thick foam ribs with foam screws while
the epoxy glue cures.
We then lay up a single layer sheet of glass fiber on a smooth
flat surface and let it cure. It will be very flexible when
it is curred so we can bend it to fit over the raw foam
already bonded to the ribs shiny side up. Weights placed
over the rib areas can be used to hold it down while it
cures. These weights can be made from long skinny sand
filled cloth bags. In some cases bungee cord can be used
to make the leading edges conform. In certain extreme cases
one could use foam screws.
The whole idea here is to cut the cost and time needed
to build an airplane and take advantage of the low cost
rotary engine.
What do you guys think of this idea?
Paul Lamar
Paul,
That is the way I did the nose on the Limo EZ. I made a male buck, glassed
one side of the divinicell foam and bent it over the buck and held it in
place with screws, then glassed the outside. Remove the screws and repair
the holes. I also found that the foam goes plastic at 240 degrees so I made
a female mold out of plywood screen and plaster, place it into a home made
oven. The mold, raw foam sheet were inside of a heat resistant vacuum bag.
After baking to 240 switch on the vacuum pump and the foam was pushed down
in the mold. after it cools glass it like the plans. You can get compound
curves. I did this for the fuselage bottom.
Joe Berki
Limo EZ
Paul,
This concept sounds surprisingly like the Fold-a-plane method that has been
around for a while. The company used to be called Vision Aircraft and their
aircraft is the personal cruiser. It appears they have had a funding and
expertise infusion and are now called Pro-Composites. Check out the building
method on their site:
http://pro-composites.com/building.htm
Regards,
Jack Hilditch
Not the same wing contruction Jack. This is the old mold less construction invented
by Burt Rutan. Glass over hot wire cut solid foam cores. As anybody that
has built a LongEZ can tell you there are hundreds of not thousands
of hours of sanding needed. Here is a screen capture from their web site.
Another draw back is it is heavier as it is hard to control the
resin content when glassing the foam. Also the wing is solid foam
so anything, such as wing tanks or landing gear, placed inside needs
extra work to hollow out the solid foam core.
The new method described above eliminates the sanding and
automatically forms a light weight sandwich skin hollow wing.
The layups are done on a large flat smooth surface so excess resin
can be squeegeed out. It is a multi step process. First the lower
skin of the top cover is laid up with the thin foam core
bonded to it. Then it is attached to the ribs causing it to conform
to the rib curve. Then the top skin is laid up on a large flat surface
and turned over. It is then curved and bonded to the now curved
and thin foam sandwich core.
The ribs can be made the same way to add strength and seal them from
gasoline.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.