Subject: cheap and quick to build composite airplanes
From: Rotary Engine
Date: 10/31/2010, 10:19 AM
To: AAA Put this in the To box


   I have always been fascinated with the idea of building
   a cheap airplane out of the lowest cost composite materials
   possible. Back in 1965 when I worked for chaparral cars I did a
   study on the lightest material to use for a race car body.
   I settled on 1/4 inch PVC foam with one layer of 4 oz glass
   cloth on either side. It was much lighter and stiffer per
   square foot than .032 aluminum.

   http://www.jmsonline.net/glass-fabric-4oz50-x-10.htm?source=googleps

   We built the body of the chaparral 2F
   out of that in a vacuum bagged female mold. The body was very
   strong and so light the paint shop doubled the weight.
   The car was capable of well over 200 MPH at some tracks like
   LeMans so the body was plenty strong enough.

   Race car bodies and airplanes have at least one unique thing in
   common. The body panels and wing panels are subject to high pressures
   distributed over the surface. The structure must be strong enough
   to resists these kinds of loads. Sandwich panels are ideal.
   At 200 MPH the worst case scenario on a wing is dynamic pressure or
   about 100 pounds per square foot.

   In other words the lift coefficient is one. If the ribs are one foot
   apart the center of the panel should not deflect excessively or fail
   with a distributed load of 8.33 pounds every inch. This is easy
   to set up a test panel and check for failure and deflection.
   It may be that rib spacing of two feet or more is acceptable depending
   the core thickness. Thicker foam cores add little weight while
   allowing greater rib spacing. In other words fewer ribs with less
   fabrication work.

   Female compound curve molds are very expensive and time consuming
   but fast airplanes can be built out of flat panels and simple curve
   parts. The Vans RV series are good examples.

   A cured sandwich panel is very strong and stiff but it is difficult at
   best to curve it to fit the top of a wing for example.

   The question is: how do we build a wing out of pre-curred flat panels?

   I think I have the answer. What we need is foam screws to screw
   the flat panels to the curved wing rib edges until the epoxy sets
   up. Here is a cheap, super light weight foam screw called a dry
   wall anchor obtainable in any hardware store. It is used to hang
   rather heavy objects on a dry wall.

   The next trick to to lay up half the sandwich panel on a flat
   surface so only one side is curred. The other side is raw foam.
   This then can be bent, raw foam up, to cover the top of the ribs
   and screwed to the one inch thick foam ribs with foam screws while
   the epoxy glue cures.

   We then lay up a single layer sheet of glass fiber on a smooth
   flat surface  and let it cure. It will be very flexible when
   it is curred so we can bend it to fit over the raw foam
   already bonded to the ribs shiny side up. Weights placed
   over the rib areas can be used to hold it down while it
   cures. These weights can be made from long skinny sand
   filled cloth bags. In some cases bungee cord can be used
   to make the leading edges conform. In certain  extreme cases
   one could use foam screws.

   The whole idea here is to cut the cost and time needed
   to build an airplane and take advantage of the low cost
   rotary engine.

   What do you guys think of this idea?

   Paul Lamar


 Paul,

 That is the way I did the nose on the Limo EZ.  I made a male buck,
 glassed
 one side of the divinicell foam and bent it over the buck and held it in
 place with screws, then glassed the outside.  Remove the screws and
 repair
 the holes.  I also found that the foam goes plastic at 240 degrees so
 I made
 a female mold out of plywood screen and plaster, place it into a home
 made
 oven.  The mold, raw foam sheet were inside of a heat resistant vacuum
 bag.
 After baking to 240 switch on the vacuum pump and the foam was pushed
 down
 in the mold.  after it cools glass it like the plans.  You can get
 compound
 curves.  I did this for the fuselage bottom.

 Joe Berki
 Limo EZ



 Paul,

 This concept sounds surprisingly like the Fold-a-plane method that has
 been
 around for a while. The company used to be called Vision Aircraft and
 their
 aircraft is the personal cruiser. It appears they have had a funding and
 expertise infusion and are now called Pro-Composites. Check out the
 building
 method on their site: http://pro-composites.com/building.htm

 Regards,

 Jack Hilditch


 Not the same wing contruction Jack. This is the old mold less
 construction invented
 by Burt Rutan. Glass over hot wire cut solid foam cores. As anybody that
 has built a LongEZ can tell you there are hundreds of not thousands
 of hours of sanding needed. Here is a screen capture from their web site.
 Another draw back is it is heavier as it is hard to control the
 resin content when glassing the foam. Also the wing is solid foam
 so anything, such as wing tanks or landing gear, placed inside needs
 extra work to hollow out the solid foam core.

 The new method described above eliminates the sanding and
 automatically forms a light weight sandwich skin hollow wing.

 The layups are done on a large flat smooth surface so excess resin
 can be squeegeed out. It is a multi step process. First the lower
 skin of the top cover is laid up with the thin foam core
 bonded to it. Then it is attached to the ribs causing it to conform
 to the rib curve. Then the top skin is laid up on a large flat surface
 and turned over. It is then curved and bonded to the now curved
 and thin foam sandwich core.

 The ribs can be made the same way to add strength and seal them from
 gasoline.

 Paul Lamar


Hey Paul,

Do you have any pictures of this laminating process in action?  I'm
having a problem understanding how you plan to curve the cured
lamination with one side cured.  My experience with cured composite
tells me that it's usually pretty stiff stuff.  Do you do this bending
when the layup is only partially cured and still flexible?

I remember seeing a similar process back in the 60s in Popular Mechanics
magazine.  They proposed building a wooden armature with frames and
stringers to support the foam.  A bit of heat applied with a heat lamp
made the foam conform to compound curves.  After the foam core material
was shaped over the armature a layer of glass was laid over the
outside.  Then the armature was removed and the inside was laid over
with glass.  I never tried it but it sounded pretty easy.

Mark LaPierre
-- 

Just and additional 3D illustration uploaded here.

When you lay up a single cloth layer 4 oz glass or carbon "laminate"
it is about as flexible as heavy weight paper.
Since it is bonded on one side to a 1/4 inch or 1/2 inch thick
foam board it gains very little bending strenght as the foam
is easily stretch on the tension side. Go to Home Depot and find
some 1/4 inch thick Styrofoam board and get a feel for it.

No pictures yet but I have been designing and building foam and epoxy
composite structures off and on ever since about 1960 when I worked for
an aero space antenna manufacturer in Arlington Va called Melpar.

BTW Some of our complete chassis at Chaparral were made solely from 6 to
10 layers of 10 ounce epoxy fiberglass curred in an auto clave.
The 2D Chaparral that won the Nurenburg ring around 1967 had a fiberglass
chassis. Not my best material choice for a chassis. The modulus of elasticity
of fiberglass is too low for a chassis where stiffness is paramount.

Paul Lamar


The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.