I have always been fascinated with the idea of building
a cheap airplane out of the lowest cost composite materials
possible. Back in 1965 when I worked for chaparral cars I did a
study on the lightest material to use for a race car body.
I settled on 1/4 inch PVC foam with one layer of 4 oz glass
cloth on either side. It was much lighter and stiffer per
square foot than .032 aluminum.
http://www.jmsonline.net/glass-fabric-4oz50-x-10.htm?source=googleps
We built the body of the chaparral 2F
out of that in a vacuum bagged female mold. The body was very
strong and so light the paint shop doubled the weight.
The car was capable of well over 200 MPH at some tracks like
LeMans so the body was plenty strong enough.
Race car bodies and airplanes have at least one unique thing in
common. The body panels and wing panels are subject to high pressures
distributed over the surface. The structure must be strong enough
to resists these kinds of loads. Sandwich panels are ideal.
At 200 MPH the worst case scenario on a wing is dynamic pressure or
about 100 pounds per square foot.
In other words the lift coefficient is one. If the ribs are one foot
apart the center of the panel should not deflect excessively or fail
with a distributed load of 8.33 pounds every inch. This is easy
to set up a test panel and check for failure and deflection.
It may be that rib spacing of two feet or more is acceptable depending
the core thickness. Thicker foam cores add little weight while
allowing greater rib spacing. In other words fewer ribs with less
fabrication work.
Female compound curve molds are very expensive and time consuming
but fast airplanes can be built out of flat panels and simple curve
parts. The Vans RV series are good examples.
A cured sandwich panel is very strong and stiff but it is difficult at
best to curve it to fit the top of a wing for example.
The question is: how do we build a wing out of pre-curred flat panels?
I think I have the answer. What we need is foam screws to screw
the flat panels to the curved wing rib edges until the epoxy sets
up. Here is a cheap, super light weight foam screw called a dry
wall anchor obtainable in any hardware store. It is used to hang
rather heavy objects on a dry wall.
The next trick to to lay up half the sandwich panel on a flat
surface so only one side is curred. The other side is raw foam.
This then can be bent, raw foam up, to cover the top of the ribs
and screwed to the one inch thick foam ribs with foam screws while
the epoxy glue cures.
We then lay up a single layer sheet of glass fiber on a smooth
flat surface and let it cure. It will be very flexible when
it is curred so we can bend it to fit over the raw foam
already bonded to the ribs shiny side up. Weights placed
over the rib areas can be used to hold it down while it
cures. These weights can be made from long skinny sand
filled cloth bags. In some cases bungee cord can be used
to make the leading edges conform. In certain extreme cases
one could use foam screws.
The whole idea here is to cut the cost and time needed
to build an airplane and take advantage of the low cost
rotary engine.
What do you guys think of this idea?
Paul Lamar
Paul,
That is the way I did the nose on the Limo EZ. I made a male buck, glassed
one side of the divinicell foam and bent it over the buck and held it in
place with screws, then glassed the outside. Remove the screws and repair
the holes. I also found that the foam goes plastic at 240 degrees so I
made
a female mold out of plywood screen and plaster, place it into a home made
oven. The mold, raw foam sheet were inside of a heat resistant vacuum bag.
After baking to 240 switch on the vacuum pump and the foam was pushed down
in the mold. after it cools glass it like the plans. You can get compound
curves. I did this for the fuselage bottom.
Joe Berki
Limo EZ
Paul,
This concept sounds surprisingly like the Fold-a-plane method that has been
around for a while. The company used to be called Vision Aircraft and their
aircraft is the personal cruiser. It appears they have had a funding and
expertise infusion and are now called Pro-Composites. Check out the
building
method on their site:
http://pro-composites.com/building.htm
Regards,
Jack Hilditch
Not the same wing contruction Jack. This is the old mold less construction
invented
by Burt Rutan. Glass over hot wire cut solid foam cores. As anybody that
has built a LongEZ can tell you there are hundreds of not thousands
of hours of sanding needed. Here is a screen capture from their web site.
Another draw back is it is heavier as it is hard to control the
resin content when glassing the foam. Also the wing is solid foam
so anything, such as wing tanks or landing gear, placed inside needs
extra work to hollow out the solid foam core.
The new method described above eliminates the sanding and
automatically forms a light weight sandwich skin hollow wing.
The layups are done on a large flat smooth surface so excess resin
can be squeegeed out. It is a multi step process. First the lower
skin of the top cover is laid up with the thin foam core
bonded to it. Then it is attached to the ribs causing it to conform
to the rib curve. Then the top skin is laid up on a large flat surface
and turned over. It is then curved and bonded to the now curved
and thin foam sandwich core.
The ribs can be made the same way to add strength and seal them from
gasoline.
Paul Lamar
Paul, Core-cell foam sold at boat fiberglass supply houses has a nice line
of pre scored PVC foams in a variety of densities. There are lengthwise
scored sheats for fitting planar curves and grid scored for compound curves.
It is absolutely manditory that there is a fully bonded surface
between the wing skin and the foam shear web coring. This will require
carefully sanded cores after the single surface glassed core is applied to
the ribs. The finished top surface can be no smoother than the core if there
is a complete bond, otherwise the epoxie adhesive will be very thick and
heavy.If there any areas of air there will be delamination at altitude and
with changing temperatures since the air is trapped in a closed area with
the closed cell foam.
I would suggest laying the cloth out between two sheats of clear
polyethalene on the flat surface and wetting out/ squeege the surface as
suggested. There will be several layers of S2 glass at different orentations
with each layer 1" larger than the one below so that the thickness at the
edges is tapered. Then peel off the plastic from the side you need to bond
to the foam and lay it on the freshly microed core after squeeging on a
little additional resin over the micro. Then continue to squeege the top
plastic sheat to remove excess resin to the front and back edges. Using the
plastic gives a smooth final surface and prevents getting the cloth
streached out of alignment/orentation. The upper plastic is initially
wrapped over the core and marked with a sharpie to use as a guide in cutting
the cloth. The bottom of the wing would be skinned first so that the upper
skin will lap over it at the leading edge to be below the chord line at the
seam.
Getting the wet out skin in place is like applying a large vinyl
sign. Leave both plastic sheats in place and drop it all on the core. move
it around to alignon with the dry core. then fold it back on it's self and
peel and cutaway the half of the bottom sheat that is up. Do the micro and
roll the glass over the fold into place. Flip the second half over the now
stuck first half, remove that lower plastic and micro the second half. Roll
the rest of the glass and plastic back over the fold and squeege everything.
Pro-set has a hardener with more than three hours open time and the
vacuum infusion hardener is usable and even longer with the regular epoxie.
Eatsern burlap.com in norfolk virginia has a good price. Any type of
fiberglass cloth and weave is available in 73" wide rools or by the yard
from Thayercraft.com in High Point NC and they have free shipping with very
good pricing.Ask for Steve if you E-mail them. He is building a Cozy in the
warehouse there.
george grimes
For a 1/4 inch thick wing top skin you don't need pre scored foam.
That is primarily for small radius compound or simple curves.
"The finished top surface can be no smoother than the core if there
is a complete bond, otherwise the epoxie adhesive will be very thick and
heavy."
I disagree with this statement as the pre curred top skin is as stiff
as heavy paper so it will be a smooth surface. The epoxy glue is mixed
with milled fibers which reduces the weight and makes it more viscous.
Less likely to get voids. Standard Rutan procedure.
In any event it is far easier and quicker to sand foam than fiberglass.
If air bubbles were a problem at altitude we would have long since
heard about it based on the number or Rutan aircraft out there.
There is no wet out skin. We are only dealing with pre curred skins
that have become somewhat stiff. One layer of 4 oz glass cloth
or carbon is not hard to wet out on a flat surface. You can
also spray on a gel coat and then the epoxy glue. A Teflon roller
might be ideal. It is even possible to buy pre curred thin fiberglass
flexible panels.
Paul Lamar
--
No, apparently there is some confusion. The Fold-a-plane
construction technique (used on the Personal Cruiser ans also
the Vision) uses no hot-wired foam. It results in a lightweight
sandwich construction. One side of the foam is glassed, then
the panel is formed in the desired shape and the other side is
glassed to lock in the shape. On very tight radius curves some
foam is removed to alow a tight bend, but on gentle curves this
isn't required. Some folks have vacuum-bagged the outer skin
during the first layup, placing the epoxy and glass down on a
very smooth surface and allowing the extra resin to come up
through holes in the foam and to be captured in a blotter layer.
The outer surface is very smooth (very little sanding needed)
and the pressure assures the fiberglass is fully wet out and all
the extra epoxy is removed. Light and strong. Steve Rahm
published the method, but I don't think he ever claimed to have
invented it.
While some folks have trouble bending "naked" foam without
snapping it, glassing and curing one side makes things a lot
easier. One famous quote "Heck, I could bend a cracker in half
if one side was glassed".
Mark W.
Sounds like you are talking about the fuselage.
The wing is what I am concerned about.
I got this screen capture right off the ex Vision now
pro-composites web site.
http://pro-composites.com/building.htmIt
clearly states hot wired foam cores are bonded to the
spar and then glassed. Scroll down the front page.
Please log on to the web site above and check it yourself.
The response to this idea I have had so far from the readers
of this newsletter speaks to the uniqueness of this type of
construction :)
If I did not already have a KISS cruiser 90% done 90% to go
kit I would build some test panels.
Paul Lamar
The fuselage of both the Vision and the Personal Cruiser can be
built using the Foldaplane method. The wings of the PC are
wire-cut foam, while the wings of the Vision use sandwich
construction (Steve Rahm is no fan of mixing fuel and
fuel-sensitive foams
in the same aircraft structure. The wing of the Vision is wet,
so urethane foams were not considered. In the Personal Cruiser,
all the fuel is in the fuselage, so a wire-cut urethane wing is used).
Anyway, the main thing is that what you are describing works
very well. It's a good way to build a light, strong wing and
aircraft.
Mark Waldron
One can buy 1/8 inch thick smooth fiberglass 48" by 48" off the shelf
from McMaster Carr. Probably over kill in thickness and too heavy
for our application for our application. Density .065 pounds per cubic
inch so a 48 by 48 by 1/8th sheet would weigh 18 pounds. Too much.
If one can find the maker they may make it in thinner sheets.
Bond the foam to one side, bend it to fit the ribs and
screw and bond it on.
I found one company that makes
36" by 48" by .3 mm thick or .018". About right.
That sheet would weigh about 2 pounds.
BTW let me know if you cannot read png's.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.