Subject: cheap and quick to build composite airplanes
From: Rotary Engine
Date: 10/31/2010, 9:54 PM
To: AAA Put this in the To box


I have always been fascinated with the idea of building
a cheap airplane out of the lowest cost composite materials
possible. Back in 1965 when I worked for chaparral cars I did a
study on the lightest material to use for a race car body.
I settled on 1/4 inch PVC foam with one layer of 4 oz glass
cloth on either side. It was much lighter and stiffer per
square foot than .032 aluminum.

http://www.jmsonline.net/glass-fabric-4oz50-x-10.htm?source=googleps

We built the body of the chaparral 2F
out of that in a vacuum bagged female mold. The body was very
strong and so light the paint shop doubled the weight.
The car was capable of well over 200 MPH at some tracks like
LeMans so the body was plenty strong enough.

Race car bodies and airplanes have at least one unique thing in
common. The body panels and wing panels are subject to high pressures
distributed over the surface. The structure must be strong enough
to resists these kinds of loads. Sandwich panels are ideal.
At 200 MPH the worst case scenario on a wing is dynamic pressure or
about 100 pounds per square foot.

In other words the lift coefficient is one. If the ribs are one
foot  apart the center of the panel should not deflect excessively
or fail  with a distributed load of 8.33 pounds every inch. This is easy
to set up a test panel and check for failure and deflection.
It may be that rib spacing of two feet or more is acceptable
depending the core thickness. Thicker foam cores add little weight while
allowing greater rib spacing. In other words fewer ribs with less
fabrication work.

Female compound curve molds are very expensive and time consuming
but fast airplanes can be built out of flat panels and simple curve
parts. The Vans RV series are good examples.

A cured sandwich panel is very strong and stiff but it is
difficult at  best to curve it to fit the top of a wing for example.

The question is: how do we build a wing out of pre-curred flat panels?

I think I have the answer. What we need is foam screws to screw
the flat panels to the curved wing rib edges until the epoxy sets
up. Here is a cheap, super light weight foam screw called a dry
wall anchor obtainable in any hardware store. It is used to hang
rather heavy objects on a dry wall.

The next trick to to lay up half the sandwich panel on a flat
surface so only one side is curred. The other side is raw foam.
This then can be bent, raw foam up, to cover the top of the ribs
and screwed to the one inch thick foam ribs with foam screws while
the epoxy glue cures.

We then lay up a single layer sheet of glass fiber on a smooth
flat surface  and let it cure. It will be very flexible when
it is curred so we can bend it to fit over the raw foam
already bonded to the ribs shiny side up. Weights placed
over the rib areas can be used to hold it down while it
cures. These weights can be made from long skinny sand
filled cloth bags. In some cases bungee cord can be used
to make the leading edges conform. In certain  extreme cases
one could use foam screws.

The whole idea here is to cut the cost and time needed
to build an airplane and take advantage of the low cost
rotary engine.

What do you guys think of this idea?

Paul Lamar

  Paul,

  That is the way I did the nose on the Limo EZ.  I made a male buck,
 glassed  one side of the divinicell foam and bent it over the buck
and held  it in place with screws, then glassed the outside.  Remove
the  screws and repair the holes.  I also found that the foam goes
 plastic at 240 degrees so I made a female mold out of plywood
screen  and plaster, place it into a home made oven.  The mold, raw foam
  sheet were inside of a heat resistant vacuum bag. After baking to
  240 switch on the vacuum pump and the foam was pushed down in the
  mold.  after it cools glass it like the plans.  You can get
compound  curves.  I did this for the fuselage bottom.

  Joe Berki
  Limo EZ

  Paul,

  This concept sounds surprisingly like the Fold-a-plane method that
  has been around for a while. The company used to be called Vision
  Aircraft and their aircraft is the personal cruiser. It appears
they  have had a funding and expertise infusion and are now called
Pro-  Composites. Check out the building method on their site:
http://pro-composites.com/building.htm

  Regards,

  Jack Hilditch

  Not the same wing contruction Jack. This is the old mold less construction
  invented
  by Burt Rutan. Glass over hot wire cut solid foam cores. As
anybody that  has built a LongEZ can tell you there are hundreds of
not thousands  of hours of sanding needed. Here is a screen capture
from their web site.  Another draw back is it is heavier as it is
hard to control the  resin content when glassing the foam. Also the
wing is solid foam  so anything, such as wing tanks or landing gear,
placed inside needs  extra work to hollow out the solid foam core.

  The new method described above eliminates the sanding and
  automatically forms a light weight sandwich skin hollow wing.

  The layups are done on a large flat smooth surface so excess resin
  can be squeegeed out. It is a multi step process. First the lower
  skin of the top cover is laid up with the thin foam core
  bonded to it. Then it is attached to the ribs causing it to conform
  to the rib curve. Then the top skin is laid up on a large flat
  surface and turned over. It is then curved and bonded to the now curved
  and thin foam sandwich core.

  The ribs can be made the same way to add strength and seal them
from  gasoline.

  Paul Lamar

  Paul,  Core-cell foam sold at boat fiberglass supply houses has a
  nice line  of pre scored PVC foams in a variety of densities. There
  are lengthwise  scored sheats for fitting planar curves and grid
  scored for compound curves.  It is absolutely manditory that there
  is a fully bonded surface  between the wing skin and the foam shear
  web coring. This will require  carefully sanded cores after the
  single surface glassed core is applied to  the ribs. The finished
  top surface can be no smoother than the core if there  is a
complete  bond, otherwise the epoxie adhesive will be very thick and
 heavy.If  there any areas of air there will be delamination at
altitude andwith changing temperatures since the air is trapped in a
closed area  with  the closed cell foam.I would suggest laying the
cloth out  between two sheats of clear  polyethalene on the flat
surface and  wetting out/ squeege the surface as  suggested. There
will be  several layers of S2 glass at different orentations  with
each layer  1" larger than the one below so that the thickness at
the  edges is  tapered. Then peel off the plastic from the side you
need to bondto  the foam and lay it on the freshly microed core
after squeeging  on a  little additional resin over the micro. Then
continue to  squeege the top  plastic sheat to remove excess resin
to the front  and back edges. Using the  plastic gives a smooth
final surface and  prevents getting the cloth  streached out of
alignment/orentation.

  The upper plastic is initially  wrapped over the core and marked
  with a sharpie to use as a guide in cutting  the cloth. The bottom
  of the wing would be skinned first so that the upper  skin will lap
  over it at the leading edge to be below the chord line at the
seam.   Getting the wet out skin in place is like applying a large vinylsign.

  Leave both plastic sheats in place and drop it all on the
  core. move  it around to alignon with the dry core. then fold it
  back on it's self and  peel and cutaway the half of the bottom
sheat  that is up. Do the micro and  roll the glass over the fold
into  place. Flip the second half over the now  stuck first half, remove
  that lower plastic and micro the second half. Roll  the rest of the
  glass and plastic back over the fold and squeege everything.

  Pro-set has a hardener with more than three hours open time and the
vacuum infusion hardener is usable and even longer with the
  regular epoxie.  Eatsern burlap.com in norfolk virginia has a good
  price.  Any type of  fiberglass cloth and weave is available in 73"
  wide rools or by the yard  from Thayercraft.com in High Point NC
and  they have free shipping with very  good pricing.Ask for Steve
if you  E-mail them. He is building a Cozy in the  warehouse there.

george grimes

For a 1/4 inch thick wing top skin you don't need pre scored foam.
That is primarily for small radius compound or simple curves.

  "The finished top surface can be no smoother than the core if there
is a complete bond, otherwise the epoxie adhesive will be very
  thick and  heavy."

I disagree with this statement as the pre curred top skin is as stiff
as heavy paper so it will be a smooth surface. The epoxy glue is
mixed with milled fibers which reduces the weight and makes it more viscous.
Less likely to get voids. Standard Rutan procedure.

In any event it is far easier and quicker to sand foam than fiberglass.

If air bubbles were a problem at altitude we would have long since
heard about it based on the number or Rutan aircraft out there.

There is no wet out skin. We are only dealing with pre curred skins
that have become somewhat stiff. One layer of 4 oz glass cloth
or carbon is not hard to wet out on a flat surface. You can
also spray on a gel coat and then the epoxy glue. A Teflon roller
might be ideal. It is even possible to buy pre curred thin fiberglass
flexible panels.

Paul Lamar
--
  No, apparently there is some confusion.  The Fold-a-plane
  construction technique (used on the Personal Cruiser ans also
  the Vision) uses no hot-wired foam. It results in a lightweight
  sandwich construction.  One side of the foam is glassed, then
  the panel is formed in the desired shape and the other side is
  glassed to lock in the shape.  On very tight radius curves some
  foam is removed to alow a tight bend, but on gentle curves this
  isn't required.  Some folks have vacuum-bagged the outer skin
  during the first layup, placing the epoxy and glass down on a
  very smooth surface and allowing the extra resin to come up
  through holes in the foam and to be captured in a blotter layer.
  The outer surface is very smooth (very little sanding needed)
  and the pressure assures the fiberglass is fully wet out and all
  the extra epoxy is removed.  Light and strong.  Steve Rahm
  published the method, but I don't think he ever claimed to have
  invented it.
  While some folks have trouble bending "naked" foam without
  snapping it, glassing and curing one side makes things a lot
  easier.  One famous quote "Heck, I could bend a cracker in half
  if one side was glassed".

  Mark W.

  Sounds like you are talking about the fuselage.
  The wing is what I am concerned about.

  I got this screen capture right off the ex Vision now
  pro-composites web site.

  http://pro-composites.com/building.htmIt

  clearly states  hot wired foam cores are bonded to the
  spar and then glassed. Scroll down the front page.

  Please log on to the web site above and check it yourself.

  The response to this idea I have had so far from the readers
  of this newsletter speaks to the uniqueness of this type of
  construction :)

  If I did not already have a KISS cruiser 90% done 90% to go
  kit I would build some test panels.

  Paul Lamar

Did any of you guys try bending a cigarette? Now roll one in a greenback
tightly. Now tie it in a knot with a quarter or half dollar
diameter. You can even stomp on it. Now untie it.

Dale Davies

We don't have cigarettes in California anymore :)

Paul Lamar




We are working at getting rid of the cancer sticks; but it is taking time. The
cancer stick rolled in money kind of demonstrates the composite advantage and
how flexible a thin sheet can be.

Dale Davies


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.