Subject: cheap and quick to build composite airplanes
From: Rotary Engine
Date: 11/1/2010, 5:44 PM
To: AAA Put this in the To box


  I have always been fascinated with the idea of building
  a cheap airplane out of the lowest cost composite materials
  possible. Back in 1965 when I worked for chaparral cars I did a
  study on the lightest material to use for a race car body.
  I settled on 1/4 inch PVC foam with one layer of 4 oz glass
  cloth on either side. It was much lighter and stiffer per
  square foot than .032 aluminum.

  http://www.jmsonline.net/glass-fabric-4oz50-x-10.htm?source=googleps

  We built the body of the chaparral 2F
  out of that in a vacuum bagged female mold. The body was very
  strong and so light the paint shop doubled the weight.
  The car was capable of well over 200 MPH at some tracks like
  LeMans so the body was plenty strong enough.

  Race car bodies and airplanes have at least one unique thing in
  common. The body panels and wing panels are subject to high pressures
  distributed over the surface. The structure must be strong enough
  to resists these kinds of loads. Sandwich panels are ideal.
  At 200 MPH the worst case scenario on a wing is dynamic pressure or
  about 100 pounds per square foot.

  In other words the lift coefficient is one. If the ribs are one
  foot  apart the center of the panel should not deflect excessively
  or fail  with a distributed load of 8.33 pounds every inch. This is easy
  to set up a test panel and check for failure and deflection.
  It may be that rib spacing of two feet or more is acceptable
  depending the core thickness. Thicker foam cores add little weight while
  allowing greater rib spacing. In other words fewer ribs with less
  fabrication work.

  Female compound curve molds are very expensive and time consuming
  but fast airplanes can be built out of flat panels and simple curve
  parts. The Vans RV series are good examples.

  A cured sandwich panel is very strong and stiff but it is
  difficult at  best to curve it to fit the top of a wing for example.

  The question is: how do we build a wing out of pre-curred flat panels?

  I think I have the answer. What we need is foam screws to screw
  the flat panels to the curved wing rib edges until the epoxy sets
  up. Here is a cheap, super light weight foam screw called a dry
  wall anchor obtainable in any hardware store. It is used to hang
  rather heavy objects on a dry wall.

  The next trick to to lay up half the sandwich panel on a flat
  surface so only one side is curred. The other side is raw foam.
  This then can be bent, raw foam up, to cover the top of the ribs
  and screwed to the one inch thick foam ribs with foam screws while
  the epoxy glue cures.

  We then lay up a single layer sheet of glass fiber on a smooth
  flat surface  and let it cure. It will be very flexible when
  it is curred so we can bend it to fit over the raw foam
  already bonded to the ribs shiny side up. Weights placed
  over the rib areas can be used to hold it down while it
  cures. These weights can be made from long skinny sand
  filled cloth bags. In some cases bungee cord can be used
  to make the leading edges conform. In certain  extreme cases
  one could use foam screws.

  The whole idea here is to cut the cost and time needed
  to build an airplane and take advantage of the low cost
  rotary engine.

  What do you guys think of this idea?

  Paul Lamar

   Paul,

   That is the way I did the nose on the Limo EZ.  I made a male buck,
  glassed  one side of the divinicell foam and bent it over the buck
  and held  it in place with screws, then glassed the outside.  Remove
  the  screws and repair the holes.  I also found that the foam goes
  plastic at 240 degrees so I made a female mold out of plywood
  screen  and plaster, place it into a home made oven.  The mold, raw foam
   sheet were inside of a heat resistant vacuum bag. After baking to
   240 switch on the vacuum pump and the foam was pushed down in the
   mold.  after it cools glass it like the plans.  You can get
  compound  curves.  I did this for the fuselage bottom.

   Joe Berki
   Limo EZ

   Paul,

   This concept sounds surprisingly like the Fold-a-plane method that
   has been around for a while. The company used to be called Vision
   Aircraft and their aircraft is the personal cruiser. It appears
  they  have had a funding and expertise infusion and are now called
  Pro-  Composites. Check out the building method on their site:
  http://pro-composites.com/building.htm

   Regards,

   Jack Hilditch

   Not the same wing contruction Jack. This is the old mold less
  construction
   invented
   by Burt Rutan. Glass over hot wire cut solid foam cores. As
  anybody that  has built a LongEZ can tell you there are hundreds of
  not thousands  of hours of sanding needed. Here is a screen capture
  from their web site.  Another draw back is it is heavier as it is
  hard to control the  resin content when glassing the foam. Also the
  wing is solid foam  so anything, such as wing tanks or landing gear,
  placed inside needs  extra work to hollow out the solid foam core.

   The new method described above eliminates the sanding and
   automatically forms a light weight sandwich skin hollow wing.

   The layups are done on a large flat smooth surface so excess resin
   can be squeegeed out. It is a multi step process. First the lower
   skin of the top cover is laid up with the thin foam core
   bonded to it. Then it is attached to the ribs causing it to conform
   to the rib curve. Then the top skin is laid up on a large flat
   surface and turned over. It is then curved and bonded to the now curved
   and thin foam sandwich core.

   The ribs can be made the same way to add strength and seal them
  from  gasoline.

   Paul Lamar

   Paul,  Core-cell foam sold at boat fiberglass supply houses has a
   nice line  of pre scored PVC foams in a variety of densities. There
   are lengthwise  scored sheats for fitting planar curves and grid
   scored for compound curves.  It is absolutely manditory that there
   is a fully bonded surface  between the wing skin and the foam shear
   web coring. This will require  carefully sanded cores after the
   single surface glassed core is applied to  the ribs. The finished
   top surface can be no smoother than the core if there  is a
   complete  bond, otherwise the epoxie adhesive will be very thick and
   heavy.If  there any areas of air there will be delamination at
   altitude andwith changing temperatures since the air is trapped in a

   closed area  with  the closed cell foam.I would suggest laying the
   cloth out  between two sheats of clear  polyethalene on the flat
   surface and  wetting out/ squeege the surface as  suggested. There
   will be  several layers of S2 glass at different orentations  with
   each layer  1" larger than the one below so that the thickness at
   the  edges is  tapered. Then peel off the plastic from the side you
   need to bondto  the foam and lay it on the freshly microed core

   after squeeging  on a  little additional resin over the micro. Then
   continue to  squeege the top  plastic sheat to remove excess resin
   to the front  and back edges. Using the  plastic gives a smooth
   final surface and  prevents getting the cloth  streached out of
   alignment/orentation.

   The upper plastic is initially  wrapped over the core and marked
   with a sharpie to use as a guide in cutting  the cloth. The bottom
   of the wing would be skinned first so that the upper  skin will lap
   over it at the leading edge to be below the chord line at the
   seam.   Getting the wet out skin in place is like applying a large
   vinylsign.

   Leave both plastic sheats in place and drop it all on the
   core. move  it around to alignon with the dry core. then fold it

   back on it's self and  peel and cutaway the half of the bottom
   sheat  that is up. Do the micro and  roll the glass over the fold
   into  place. Flip the second half over the now  stuck first half, remove
   that lower plastic and micro the second half. Roll  the rest of the
   glass and plastic back over the fold and squeege everything.

   Pro-set has a hardener with more than three hours open time and the
   vacuum infusion hardener is usable and even longer with the
   regular epoxie.  Eatsern burlap.com in norfolk virginia has a good
   price.  Any type of  fiberglass cloth and weave is available in 73"
   wide rools or by the yard  from Thayercraft.com in High Point NC
   and  they have free shipping with very  good pricing.Ask for Steve
   if you  E-mail them. He is building a Cozy in the  warehouse there.

   george grimes

  For a 1/4 inch thick wing top skin you don't need pre scored foam.
  That is primarily for small radius compound or simple curves.

  "The finished top surface can be no smoother than the core if there
  is a complete bond, otherwise the epoxie adhesive will be very
  thick and  heavy."


  I disagree with this statement as the pre curred top skin is as stiff
  as heavy paper so it will be a smooth surface. The epoxy glue is
  mixed with milled fibers which reduces the weight and makes it more
  viscous.  Less likely to get voids. Standard Rutan procedure.

  In any event it is far easier and quicker to sand foam than fiberglass.

  If air bubbles were a problem at altitude we would have long since
  heard about it based on the number or Rutan aircraft out there.

  There is no wet out skin. We are only dealing with pre curred skins
  that have become somewhat stiff. One layer of 4 oz glass cloth
  or carbon is not hard to wet out on a flat surface. You can
  also spray on a gel coat and then the epoxy glue. A Teflon roller
  might be ideal. It is even possible to buy pre curred thin fiberglass
  flexible panels.

  Paul Lamar
  --
   No, apparently there is some confusion.  The Fold-a-plane
   construction technique (used on the Personal Cruiser ans also
   the Vision) uses no hot-wired foam. It results in a lightweight
   sandwich construction.  One side of the foam is glassed, then
   the panel is formed in the desired shape and the other side is
   glassed to lock in the shape.  On very tight radius curves some
   foam is removed to alow a tight bend, but on gentle curves this
   isn't required.  Some folks have vacuum-bagged the outer skin
   during the first layup, placing the epoxy and glass down on a
   very smooth surface and allowing the extra resin to come up
   through holes in the foam and to be captured in a blotter layer.
   The outer surface is very smooth (very little sanding needed)
   and the pressure assures the fiberglass is fully wet out and all
   the extra epoxy is removed.  Light and strong.  Steve Rahm
   published the method, but I don't think he ever claimed to have
   invented it.
   While some folks have trouble bending "naked" foam without
   snapping it, glassing and curing one side makes things a lot
   easier.  One famous quote "Heck, I could bend a cracker in half
   if one side was glassed".

   Mark W.

   Sounds like you are talking about the fuselage.
   The wing is what I am concerned about.

   I got this screen capture right off the ex Vision now
   pro-composites web site.

   http://pro-composites.com/building.htmIt

   clearly states  hot wired foam cores are bonded to the
   spar and then glassed. Scroll down the front page.

   Please log on to the web site above and check it yourself.

   The response to this idea I have had so far from the readers
   of this newsletter speaks to the uniqueness of this type of
   construction :)

   If I did not already have a KISS cruiser 90% done 90% to go
   kit I would build some test panels.

   Paul Lamar


  At AirVenture 2010 I attended several workshops by Scott VanderVeen from
  Pro Composites.  This is a very interesting process that results in a
 fairly
  smooth surface.  Pro Comp has a video for those of us whom are newbies at
  composites.  I like Pauls' idea of vacuum bagging on a flat surface. How
  about hinging two large honeycomb panels on the long side to make the
  buildup, then flip and bag for this flat surface?

  For least weight Scott recommends a glass bead/resin layer squeegeed on
 the
  foam and then peel ply over the glass to soak up excess resin. Would this
  work on 4 oz cloth?


  Could plywood stations (essentially exterior ribs) work to form the wing
  exterior panel and then glass the interior side to hold the shape? I have
  been pondering this method to form our leading edge, which then attaches
 to
  the ribs using adhesives and additional  pull rivets at the spar.

 Dan F

Paul, Air filled voild in wings have been a problem with solid skins over a
foam core. Alan Shaw had a business building wings for Velocity aircraft
after he stopped working for Velocity. He used a closed pressure mold with
precured skins over featherlite cores. There were cases of 30% voids during
production. Some were salvaged by injecting resin through a hole at the end
of a void until it came out a hole at the other end. Several of the
resulting wings delaminated at altitude and were scrapped. The statement
that if this was a problem the many Rutan designed moldless composite wings
would exhibit this failure mode may not be accurate. The Rutan aircraft are
ALL wet layup over the cores with shear webs and spar caps also laid up wet
over the cores. With reasonable workmanship full contact with the microed
cores is relatively easy.There have also been some delamination problems
associated with hardshelling foam cores. This method arguably passes tests
of peel strength, however some delamination has occured  at the junction of
the skin and micro surface.
         One other point is the single layer of 4 Oz glass. At a minimum one
layer of 8 harness satin with spanwise orientation and one at + or - 45
degrees for torsional loads is required. The cloth could be uni directional
if minimum weight is a concern. Of secondary concern is puncture damage from
spectators at airshow parking areas or dropped tools by the builder. Often
this determines the plies necessary more than the tensile strength of the
materials.
     I saw the refrence to "I" beam manufactured spars. If the spar is fit
through the ribs to leave the rib perimiter continuous it might be easier to
use a tubular spar particularly if wing twist has to be built in.The inboard
portion of the spar could have cloth laid up to progressivly increase
thickness and perhaps some phenolic blocks incorporated for the attach pins
to the fusalogue. Just a thought.
Also you might consider tapering off the foam before the inner skin as
applied  on the flat work table so that the inner and outer skin would be
bonded at the leading edge and somewhere at the rear.

george grimes

Hey I am not responsible for some ones lousy workmanship :)
One must be doing bad work indeed to get a 30% void. It is a simple
matter to check the foam for flatness with a straight edge.
Sand the foam with a long straight 2 by 4 with sand paper
on one side.  Deal with the problem instead of throwing the baby
out with the bath water. Just be careful.

Use the coin tap test to detect voids. Robin does that on
air buses. SOP on airliner composites.

The first layup that controls the torsional stiffness can be anything
you want in the way of fiber orientation. The outer skin does nothing
but protect the foam from damage and adds panel stiffness.

The leading edge can be solid foam with a wet layup. That will cut down
enormously on the sanding.

Time is money. This is a way to cut the time and cost needed to build
the airplane. It does not make sense to use a construction technique that
takes a year to sand smooth. Not to mention the mess and several coats
of paint.

Paul Lamar.
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.