Subject: Battery and motor voltage
From: Rotary Engine
Date: 11/2/2010, 10:20 AM
To: AAA Put this in the To box


Hi Paul,
Is it suitable to replace standard Renesis lead battery (12v
70Ah) with Li-Polymer one?

Expert from engine starter company asses that working power of
Renesis starter is around 2kW and starting current (duration max
0.5ms) is around 700A. By the factory standard starter has to
manage 3 times 30 seconds without cooling pause. So battery
capacity has to manage it - my condition for dimensioning

I calculate that 45C 11.1v 15Ah Li-Polymer battery would be
strong enough to fulfill demands. I really do not know if such a
small and light battery is really suitable for starter. It
weighs around 1.3kg/3lb comparable with 18kg/40lb for lead one.
Weight ratio between technologies is around 1:12 and somehow it
is difficult to accept replacement. If this really works it will
be excellent contribution to aircraft weight reduction. Li-Poly
lifetime is about 1/2 lead one and is approx. 3 times more
expensive.

Do you know obstacles for usage of higher voltage around Renesis
engine? I would like to use 28v DC for whole aircraft.

Viktor

Slovenia, Europe

I am no expert but as I recall Lithium Ion batteries require special
computer controlled chargers. Lead Acid batteries do not. Otherwise
you risk blowing up the battery.

Back in the old days (1960's) we used Nickel Cad aircraft batteries
in our Chaparral race cars successfully with no special chargers.

Doug Fir in Japan knows far more about this than I do.

Paul Lamar


http://www.powerstream.com/li.htm

"The basic algorithm is to charge at constant current (0.2 C to
0.7 C depending on manufacturer) until the battery reaches 4.2
Vpc (volts per cell), and hold the voltage at 4.2 volts until
the charge current has dropped to 10% of the initial charge
rate. The termination condition is the drop in charge current to
10%."



Not worth it for the airplane.  I just installed Li Po batteries in my
skateboard, replacing the SLA batteries it came with.  (36Vx16Ah in a 2x10
configuration)

In the skateboard it cut 10 lbs off the weight and more than doubled the
range - BUT, the battery upgrade cost me more than the whole skateboard
- even with a killer deal on batteries and I did the installation myself.

The first problem is that you cannot easily keep Li Ion (liPo etc) connected
to the electrical system of the aircraft.  The initial charge would be too
high and if that didn't make them blow up, They would either over-charge or
undercharge if you left them connected to the system.

It would be OK to have them connected to the system if you over sized the
pack in both size and volts.  So 15v would not over charge... 4.2vx4 for a
max tolerable voltage of 16.8v.  Nomimal voltage would be 3.7x4=14.8v. These
batteries really dont like to be charged at more than 0.2-1C, *maybe* 2C for
short periods if you have a very high current type battery but I have not
seen any rated for 2C charge.  So if you figure 80A max charge rate, you
would need an 80Ah pack at minimum.

That would get very expensive and weight would be coming up on that of an
SLA battery.  You might say - but at least I would have 80Ah for reserve.
But since you will only be charging to 14.5V or so, you will not be using
even half of the battery's capacity - more like about 30Ah of the rated
80Ah.  So what you just ended up with is a $2000 30Ah (effective) battery
that weighs almost as much as a 30Ah SLA.  (along with other downsides as
below)

Or you could keep the LiPo separate from the rest of the electrical system.
That would mean a separate charger and an inverter (or a DC charger that
probably just has a built-in inverter). And you would still need to have at
least a small SLA connected to the system for alternator noise and sudden
power loss.

Other important factors:
LiPo Li-Ion batteries are at high risk for fire. (remember all those laptop
and cell phone batteries catching on fire?)  The risk is mitigated with
proper management but there is still always the risk.

You need a controller board to manage each cell individually.  No single
cell can be allowed to charge or discharge at an excessive rate, over
charge, or over discharge, lest you risk a fire.  (And with an 80Ah pack
that would be a pretty big fire).  That controller board is another cost and
failure point. And, all of the boards I have seen, simply shut down the pack
if one of the cells is out of range - not good for aircraft use. Also, you
need to periodicly balance the cells.  A good controller board will do that,
but they do it at the end of a full charge.  Since you would not be reaching
full charge they would not be balanced and you would need to pull the
batteries every 20 cycles or so and manually balance them (requiring time
and equipment).  What you would really do, is build a custom controller
board for aircraft use.

They are rather heat intolerant.  There are stories of LiPo's for RC cars
being charged up, then put in the trunk where they get hot, raising the
voltage above the upper limit for any one of the cells, then burning down
the car (the big people car - not just the RC car).  At least 2 guys have
burned down their houses - probably by incorrectly setting the charger.  The
RC cars themselves burn down all the time from overheat and/or too much
current.  Even without fire, repeated heat cycles (like sitting on the
flight ramp) are damaging and will degrade your $2000 battery pretty
quickly.

So, these batteries are not going to replace lead acids in cars OR airplanes
anytime soon.

The only application I can think of would be a racing rotary aircraft where
there is no charging system.  The LiPo would be a light-weight way to power
the fuel pumps, coils, etc for the duration of the (short) race and be
re-charged afterward (like at Reno).  For that you would probably use an
11.1v (nominal) LiPo pack with 40 or so Ah. (weighing in around 12lbs)


David Leonard

Turbo Rotary RV-6 N4VY
http://N4VY.RotaryRoster.net
http://RotaryRoster.net


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.