Matt-
I have never built a Rutan type composite airplane but
I wonder why one cannot sand the foam before applying the
wet layup to insure an accurate surface.?
Paul Lamar
One can absolutely sand the core before applying the wet layup.
I understand that Berkuts were built starting with cores that
were hot wired oversize and which were then sanded to precise
dimensions.
Matt-
Well then what about bonding on pre curred skins with
a finished smooth surface? The spar handles all the bending
loads.
One advantage of the sandwich skin idea above compared to a solid
foam core is you get more internal volume in the wing for fuel,
control linkages and perhaps landing gear.
No need to make separate hollow strakes.
Paul Lamar
--Another way to build quicker - and still cheap - is to avoid
the need of curved surfaces :)
http://www.facetmobile.com/
Philippe Dejean
Barney Wainfan is relatively local and I have been over
to his hangar and seen the airplane. An interesting experiment
but not too practical for long distance travel.
My interest in aviation is low cost high speed cross country
travel rather than buzzing around the airport low and slow. Here
in the western states, cites and other places of interest are far
apart, so it takes a lot of time getting anywhere. The same goes
for Australia, South America, Africa, China and Russia only
double as four lane high speed roads are rare if not non existent.
The governments in those countries should promote general
aviation and build small airports because it is good for the
economy and removes some of the need to build expensive super
highways with precious tax money. Perhaps this is giving
governments more intelligence and fore site than is warranted ;)
In the eastern part of this country and in Europe one can drive
from one place of interest to another in a relative short time
period as the roads are good. Recreational aviation is king. I
notice this when I travel to Aero in Friedrichshaven every year.
Lots of light sport size airplanes, motor gliders and very few
serious and fast cross country airplanes like the Lancair ES or
RV10. I guess it could be related to government restrictions and
to disposal income. Low individual taxes. One can see this by
looking at Goggle maps of airports around the world. Where I live
there are at least four general aviation airports within 40
miles. Santa Paula, Camarillo, Oxnard and Santa Barbara. There
are probably 50 within 200 miles of here.
Paul Lamar
Even here in Europe where average travel distances are much
shorter, there is a need for such high speed cross country
airplane.
High speed trains (about 200 Mph commercial speed from and to
city centers) are the easiest way to travel, but the tracks
lead to a limited number of stations...
IMHO, The most suitable plane for this mission would be similar
to Steve Jones' White Lightning, a little lighter with the
use of carbon fiber.
This airplane could be powered either by :
- one 200 HP Delta hawk engine (good BSFC, running on Jet A1,
turbo normalized up to FL180)
- one 230 HP (about) turbocompound Wankel
The main problem is to produce a large number of kits at an
affordable price
Philippe Dejean
200 MPH only works in the flat part of France. After the 2005
Paris air show I dropped Robin off in downtown Paris at the train
station. Took her all day to get to Trento in Northern Italy.
Only about 500 miles as the crow flies. She needed to be there
a day before I wanted to be there :)
I then drove to Trento stopping off in Geneva to see Mistral.
I then took the Mount Blanc tunnel to Italy the next morning
and despite heavy traffic around Milano made it to Trento in
about half a day from Geneva.
The Delta Hawk engine is vapor ware. Been around for years
and I have never seen one flying. It is a piston ported
super charged two stroke so I rather doubt the BSFC claims.
The scavenge ratio is a big problem for that type
of 2 cycle engine. Diesel or otherwise.
GM built some similar engines with exhaust valves in
the head that worked much better. Even they are gone now.
The turbo compound four stroke diesel is becoming the engine
of choice for heavy duty applications.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.