I'm in the midst of tuning my engine. I was getting the bogging and then
surging right at the point that the secondaries were turning on, and I also
seemed to get good results by richening it up for the first 3 bins where the
secondaries are cutting in. This is on the ground, of course. I think that
I will see some need for tuning in the high RPM/ low MP mapping table when I
am in the air descending. Or maybe not, as I recall the airplane was making
a siren song to me that it was running smoothly as I was descending to land,
calling for me to go around because it was now smoothing out.
My spark timing is right on the money.
Also, my primaries are 28 lb, and the secondaries are 40 lb injectors, so my
staging point is at map station 89~90 right now. I think that might be a
little
high.
Here's another unrelated issue- I have an RV-4, with the fuel being taken
out of and returned only to the right tank. I have an AN-6 line feeding a
facet pump located just aft of the batteries, and it transfers fuel to my
right hand tank when I want to transfer the fuel. Both tanks are vented
separately. Here's the problem: I started out with 12.5 gallons in the
right tank, and 6.5 in the left. After running the engine on the ground for
1 hour, I ended up with 12.7 gallons in the right and 1.7 in the left,
without ever having run the transfer pump. The only thing I can think of
having happened is that the plane was parked slightly- 1 degree or so-right
wing down. The facet pump I believe has a one way valve which would allow
fuel to flow downhill to the right tank. That's my theory, can anyone else
offer a theory as to why the fuel is self transferring?
Brian Trubee
RV-4
Your prop turns clockwise tending to lower the left wing
deflecting the landing gear so that is not it. Unless of
course you pull the power quickly and get some spring back
from the landing gear. Then the fuel could slosh into the
right wing through the one way valve in the transfer pump.
Double check the plumbing :)
Where are the fuel tank vents?
BTW sitting in the car the engine from the drivers
point of view the engine rotates counter clockwise.
Therefor when turned around in the tractor airplane
the engine rotates clockwise. Left wing down right
wing up.
The same as your prop so you must be running a 2.85:1 gear
box. Is that correct?
Paul Lamar
Yup, 2.85/1 so I'm turning clockwise from where I sit in the cockpit. The
plane
was sitting on a slight, very slight grade to the right, so that might have
something to do with it. Both tank vents are located next to each other near
where the right gear leg exits the fuselage. I ran it for an hour or so, but
didn't see any evidence that fuel leaked out anywhere. There was some engine
surging, so I guess the longitudinal rocking could have caused some fuel to
slosh to the right, but the left tank was near full, and the engine takes
and
returns fuel to that tank.
I'm going to hold off on the taps for now, I think I might have the engine
running smoothly.
Puzzling.
Brian Trubee
I'll bet the tank vent is facing forward correct?
-------------------------------------------------
Never mind. I found a picture. They are indeed facing forward.
The prop blast is pressurizing the left tank and forcing the fuel
over to the right tank. This is fine but you need to control
it. If the vent is wrong on the right tank this could force
fuel overboard through the right tank. To prevent this
you can use a one way valve in the vent lines.
At 100 MPH prob blast the left tank will be pressurized
to .18 psi. 6 inches of fuel is about .2 psi.
so .18 psi will force fuel into the right tank
when the level in the right tank is about five inches or
lower. In theory both tanks should be pressurize the same
so the right tank vent may be plugged.
Good thing you noticed that as that could cause real
problems on a cross country trip cruising at a higher
speed. With a prop blast of 150 MPH the tank pressure
will be .4 psi. That could force fuel overboard
with a full right tank.
I would connect the the right tank vent into the left
tank. You could probably get away with no transfer
pump but you should try it first with the pump
off.
You have not begun to tune :)
Here is an old message on the subject perhaps you forgot about.
Paul Lamar
------------------------------------------------
-------- Original Message --------
Subject: EFI Fuel feeding system
Date: Sun, 12 Nov 2006 09:55:05 -0800
From: Rotary Engine
<rotaryeng@earthlink.net>
To: AA-me
<rotaryeng@earthlink.net>
snips......
I figured I'd go really simple and copy Tracy Crook's system- take the
fuel out of and return to the left tank, and use a pump to transfer
fuel out of the right tank to the left. The worst that can happen is to
transfer too much over to the left tank and pump the excess overboard.
Then you are left with the right tank empty and the left tank full.
(Unless someone can see some other scenario that I have overlooked)
I've got one of Bulent's 6 port valves left over, so any offers on it
will be considered.
Brian Trubee
That is fine as long as you don't get distracted and let
it pump fuel overboard.
Another scenario is if the right tank vent is pointing forward
it will empty the right tank to the left tank and force all fuel
out of the left tank vent in short order at over 150 MPH.
The safest thing to do is keep that valve you have and use it.
Paul Lamar ...No rotor no motor.
--------------------------------------------------
"My spark timing is right on the money."
Can I ask where you have that set?
Jay
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.