Subject: Brian Trubee Latest tunning results
From: Rotary Engine
Date: 11/8/2010, 9:07 PM
To: AAA Put this in the To box



 I'm in the midst of tuning my engine. I was getting the bogging and then
 surging right at the point that the secondaries were turning on, and I
also
 seemed to get good results by richening it up for the first 3 bins where
the
 secondaries are cutting in.  This is on the ground, of course.  I think
that
 I will see some need for tuning in the high RPM/ low MP mapping table when
I
 am in the air descending.  Or maybe not, as I recall the airplane was
making
 a siren song to me that it was running smoothly as I was descending to
land,
 calling for me to go around because it was now smoothing out.


 My spark timing is right on the money.

 Also, my primaries are 28 lb, and the secondaries are 40 lb injectors, so
my
 staging point is at map station 89~90 right now. I think that might be a
 little
 high.

 Here's another unrelated  issue- I have an RV-4, with the fuel being taken
 out of and returned only to the right tank.  I have an AN-6 line feeding a
 facet pump located just aft of the batteries, and it transfers fuel to my
 right hand tank when I want to transfer the fuel.  Both tanks are vented
 separately.  Here's the problem: I started out with 12.5 gallons in the
 right tank, and 6.5 in the left.  After running the engine on the ground
for
 1 hour, I ended up with 12.7 gallons in the right and 1.7 in the left,
 without ever having run the transfer pump.  The only thing I can think of
 having happened is that the plane was parked slightly- 1 degree or
so-right
 wing down.  The facet pump I believe has a one way valve which would allow
 fuel to flow downhill to the right tank.  That's my theory, can anyone
else
 offer a theory as to why the fuel is self transferring?


 Brian Trubee
 RV-4


 Your prop turns clockwise tending to lower the left wing
 deflecting the landing gear so that is not it. Unless of
 course you pull the power quickly and get some spring back
 from the landing gear. Then the fuel could slosh into the
 right wing through the one way valve in the transfer pump.

 Double check the plumbing :)

 Where are the fuel tank vents?

 BTW sitting in the car the engine from the drivers
 point of view the engine rotates counter clockwise.
 Therefor when turned around in the tractor airplane
 the engine rotates clockwise. Left wing down right
 wing up.

 The same as your prop so you must be running a 2.85:1 gear
 box. Is that correct?

 Paul Lamar


 Yup, 2.85/1 so I'm turning clockwise from where I sit in the cockpit. The
 plane
 was sitting on a slight, very slight grade to the right, so that might
have
 something to do with it. Both tank vents are located next to each other
near
 where the right gear leg exits the fuselage. I ran it for an hour or so,
but
 didn't see any evidence that fuel leaked out anywhere. There was some
engine
 surging,  so I guess the longitudinal rocking could have caused some fuel
to
 slosh to the right, but the left tank was near full, and the engine takes
 and
 returns fuel to that tank.
 I'm going to hold off on the taps for now, I think I might have the engine
 running smoothly.

 Puzzling.


 Brian Trubee

 I'll bet the tank vent is facing forward correct?

 -------------------------------------------------

 Never mind. I found a picture. They are indeed facing forward.
 The prop blast is pressurizing the left tank and forcing the fuel
 over to the right tank.  This is fine but you need to control
 it. If the vent is wrong on the right tank this could force
 fuel overboard through the right tank. To prevent this
 you can use a one way valve in the vent lines.

 At 100 MPH prob blast the left tank will be pressurized
 to .18 psi.  6 inches of fuel is about .2 psi.
 so .18 psi will force fuel into the right tank
 when the level in the right tank is about five inches or
 lower. In theory both tanks should be pressurize the same
 so the right tank vent may be plugged.

 Good thing you noticed that as that could cause real
 problems on a cross country trip cruising at a higher
 speed. With a prop blast of 150 MPH the tank pressure
 will be .4 psi. That could force fuel overboard
 with a full right tank.

 I would connect the the right tank vent into the left
 tank. You could probably get away with no transfer
 pump but you should try it first with the pump
 off.

 You have not begun to tune :)

 Here is an old message on the subject perhaps you forgot about.

 Paul Lamar


 ------------------------------------------------

 -------- Original Message --------
 Subject: EFI  Fuel feeding system
 Date: Sun, 12 Nov 2006 09:55:05 -0800
 From: Rotary Engine <rotaryeng@earthlink.net
 To: AA-me <rotaryeng@earthlink.net

 snips......

 I figured I'd go really simple and copy Tracy Crook's system- take the
 fuel out of  and return to the left tank,  and use a pump to transfer
 fuel out of the right tank to the left. The  worst that can happen is to
 transfer too much over to the left tank and pump the excess overboard.
 Then you are left with the right tank empty and the left tank full.
 (Unless someone can see some other scenario that I have overlooked)

 I've got one of Bulent's 6 port valves left over, so any offers  on it
 will be considered.

 Brian Trubee


 That is fine as long as you don't get distracted and let
 it pump fuel overboard.

 Another scenario is if the right tank vent is pointing forward
 it will empty the right tank to the left tank and force all fuel
 out of the left tank vent in short order at over 150 MPH.

 The safest thing to do is keep that valve you have and use it.


 Paul Lamar ...No rotor no motor.

 --------------------------------------------------

 "My spark timing is right on the money."

 Can I ask where you have that set?

 Jay


 Spark timing is set at 22~23 btdc @ 4000 RPM.

 I think I'm going to try the easiest solution to the unwanted fuel
transfer problem first- that would be to put one way check valves into the
vent lines. But I think there will still be unequal tank pressures due to
the fact that fuel is being drawn out of the right tank, so the left might
have slightly higher pressure and want to contribute to the right. Anyone
know where to get smaller check valves which have a very light opening
pressure?

 Maybe a simpler solution is to put a manual valve in the transfer line.

 On second thought, putting check valves in the vents might be a real
bonehead move, since in climbing up from sea level to 17,000
feet(unrealistic, but possible) you'd be developing a pretty good pressure
differential inside the tank, at least if you were not to draw fuel from it.
I think the easiest solution is to put a manual valve in the transfer line.


 Brian Trubee

 Check valves in vent lines are SOP for some certified aircraft.
 Compared to EFI fuel pressure of 50 psi a few psi
 due to altitude is minuscule.

 Paul Lamar


Hi Brian,


Congratulations on getting airborne.  About check valves.  They are only as
reliable as the fuel filter.  Any grit in the fuel and they are defeated.
 Most of the SeaWind builders have taken them out in favor of manual valves.
    Set up properly  manual valves can also act as an emergency fuel shut
off system.

Long flights require fuel management skills and pilots of really long
flights have been known to use kitchen wind-up timers to remind them to
change tanks every 30 mins.

I wouldn't restrict the vent lines with a check valve, What size lines are
the vent lines now?

All the best


Doug in Japan

I disagree Doug. One can lose fuel out of a vent line
when in uncoordinated turns and if the tank vent line happens
to have a low pressure applied or one tank vent is seeing
dynamic pressure and the other is not.

A check valve on the vent line is mainly a screw up preventer both
design and operation.


Paul Lamar




Paul, Why not have the vents connected to a tee with a single outlet.
Also Bruce Bohanan(sp?) who was setting time to climb records in the Exxon
sponsored "flying tiger" had a wing tank sucked out of shape/collapsed due
to a vent line and changes in barometric pressure with altitude while
descending.

george grimes

The only way that could happen is if the vent line became plugged
with something. The one way valves rarely, if ever fail in
that mode. They are more likely to just leak in the blocking direction.
Perhaps a large insect was sucked into the vent line.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.