Subject: Norton / Midwest Rotary Aero Engine
From: Rotary Engine
Date: 11/13/2010, 1:02 PM
To: AAA Put this in the To box


 Paul
 My Norton Rotary story starts out many years ago when I first saw the
 Norton engine being marketed by a company that is now defunct.  the engine
 looked small, and the stats (although no aviation engine had been produced
 looked impressive.  (I can only remember the colors of that companies logo
 as being green and the engine being just a purposed minor part of their
 line)

 That engine never came to market, and I put a VW engine in my dragonfly.

 After my first flight, many years after I had seen that engine, because of
 oil pressure problems, and a broken Canard, I removed the engine and
 rebuilt it, to find the bearings totally shot (was a new aircraft
 conversion, built by the converter incorrectly).  After the rebuild, I had
 some spinal surgery (not aviation related, from which the recovery was
 extensive and I went out to the airport, sat and just stared at my project
 for what seemed like years.  Ultimately, I realized that I would, indeed
 walk again and decided to once again address the engine.  About that time,
 I read that the Norton engine was being made available as the AE100R by an
 English company called Midwest and one was available in the US (they had a
 rather strange distributorship system, with sometimes strange people doing
 the distributing.) I felt that because I had indeed survived and was
 learning to walk reasonably well, that I deserved that engine which I had
 lusted over, but until now was unavailable.

I was able to get the two rotor. There was little factory or distributor
 backup, at that time.  The engine had 2 carburetors and the lubricating oil
 lines were plastic.  The engine has a plastic(for want of a better word)
 induction manifold sitting on top, under which was another manifold for the
 cooling air/oil mixture to be expressed out of the engine.(more about this
 later) The intake manifold was quite substandard and needed a lot of
 reinforcement, and the 2 tubes, one to each rotor were similarly
 constructed.  I believe the carbs were Tillotsens.

 The engine was a combination of water and air cooled. The trochoids were
 cooled by the standard H2O antifreeze method, water pump at the back of the
 engine, directly driven off of the eccentric.  The rotors were cooled
 differently.

 Oil was injected into the trochoids, for obvious reasons. It was also
 injected into the bearings (probably roller) for lubrication.  There is no
 oil pressure or sump in this system.  It appears as if the oil, after
 lubricating the bearings, weeps into the center of the engine at which
 point it is picked up by an airstream created by a turbine, belt driven,
 and blown into the innards to cool the rotors.  This, then oil and heat
 laden air is exhausted out of the engine coursing through the lower
 manifold indicated above.  It is then routed to a separator, basically an
 evaporator pad.  Some of the oil (about 1/3 of that used for the bearing
 lubrication and cooling) drips to the bottom of the enclosure and is
 returned to the oil storage tank, and the rest blows overboard..  The
 system works well, as long as proper ducting, etc is used.  You cannot use
 premix in the fuel as the bearings will not be lubricated and your flight
 will be very short.


 There are a couple of problems with the above mentioned system.  1.  The
 recommended oil is very expensive (synthetic "Goldenspectro- Premix" from
 what I remember.  A Mobile Pegasus product is also approved ( I have a 55
 gal drum full of the stuff which serves as a table, in my hanger)

 2. The oil laden air, exhausting from the engine (which can be used for
 Carb heat or alternate air) has to go somewhere, and it coats any aircraft
 part downwind from it.  In my case, the Right wheel pant was always covered
 with unburned goo after a flight.

After I installed the engine and had some flights with it, I had major
 ignition problems with it (the installed system was crap, and in fact
 decided to remove the engine.  The Midwest company was quite wanky, seemed
 always to be on the verge of bankruptcy and was looking for an angel.
 Response from them was, and many that of the people related to the company,
 was less that what I wanted, in terms of safety and backup.  I did not like
 the plastic lines, the Carbs were difficult or impossible to properly
 adjust.  (by the way, there were 2 of these engines on our field, mine
 being one of them, the other in a beautifully built Kitfox, not flown at
 the time..  I don't know if has flown yet (several years later, although it
 has changed owners).  Because of bad feelings of the future of Midwest, I
 decided to dismount the engine and look for other avenues of power.




As I was pondering this decision and after, frankly hugely negative feelings
 that I got from the factory Rep at OSH, I heard the Diamond company had
 come in as the savior.  Elated, thinking that this would resurrect my
 almost abandoned engine, I found out that they had made many modifications
 to it, based on the few that were out in the field.  These improvements
 included a different coating of the combustion chamber a new EFI and
 ignition system, metal lubrication lines and a much stronger manifold
 assembly.  They also modified the cooling turbine (which had been changed
 at least 2X before because, I believe, they were disintegrating or breaking
 in use.

 So I packaged my engine, sent it back to England to Midwest (Now thinking
 it was Diamond) to have it rebuilt (after about only 25 to 20 hours, if
 that) to their new AE110R.  now rated, by the at 110 or 115 HP.
 configuration.  and reinstalled it.

 After about 75 or 80 hours of flight, on approaching a landing, in dicy
 weather conditions, the engine refused to accept throttle on level off.  It
 did not stumble, but continued idling at 2K until my arrival in a way too
 short field, and the necessary destruction of the aircraft to save my own
 bacon.  The engine, in effect was still idling when I stopped, and I shut
 it down normally (of course, the three bladed C/s prop had fractured it's
 Warp drive blades.

 Then the real fun began. I was made aware that the ignition system had a
 fault log which could be downloaded and evaluated, however only Diamond had
 the software to do it, and they refused to release it due to proprietary
 reasons.  They said that I could ship the engine to them and they would
 send me a report---Ya Right.

 Although by this time, my contact person, at the company was great, I hit a
 brick wall.  Shortly thereafter I got a letter from a Barrister, of the
 company, that Midwest, a company whose stock was wholly owned by Diamond
 had, in fact been closed (bankrupted) and basically was told to "Pound
 sand".  A personal meeting between me and Christian Dries (Owner of
 Diamond) resulted in the same pound sand philosophy.  The engines did
 resurface at Austro later.


 An additional problem with the AE100 is that the Champion spark plugs
 (surface electrode) used are no longer manufactured.  With the
 remanufacturing, they went to a similar, but not directly retrofittable
 Bosch plug, which also is no longer manufactured.  (I have about 100 of
 these plugs, still in their original boxes if anybody is interested.  They
 were used on the BMW, M1 (I believe that is the model) as the originals
 supplied.

 Because of my experience with diamond, I personally would certainly have
 great misgivings about dealing with them in any capacity.  By the way the 2
 rotor is not certified, the 1 rotor was.

 I actually loved the engine, despite the oil problems. Reminds me of the
 joke "Other than the third act, Mrs.  Lincoln, how did you like the play?

 If you still want one, I suggest you contact a man by the name of Richard
 Nagus, (once working for Diamond/midwest) he is involved with Nortons in
 England, and he can give you more info on the current status of parts
 availability and support.  The fact that you saw parts at Diamond does not
 necessarily mean that you can get them.



 My suggestion, if you want to use this engine, get a 110R, design your own
 electronics and prepare not only for no factory backup, but because of the
 relatively small number of 2 rotors in the field, practically no support
 from users

 If you do get the 100R, make sure that the turbine [blower] is the proper
 one as
 when it sheds  blades or whatever it does, you may find yourself in a
 world of hurt.

 Engine itself ----when running ---3 canards up (out of 5)

 Support  and recommendations,10 canards down

 I have attached a photo of the installation (early photo)


 Rich

 What year was this Rich?

 Paul Lamar


 Hello Paul/ John/ Brian and Rich, who wrote quite a comprehensive story
 about his experiences with Norton AE100R:

 Yes, there are some experts, who know a lot of these early Norton rotaries.
 You already mentioned Mr. Richard Negus (retired, but having Norton as a
 hobby). Another is Mr. Martin Ruhe, who also worked at Midwest. Also Mr.
 Peter Morris, who is now working at Andover Norton, knows a lot of Norton
 and its spares. Surely there are some others, who might be helpful?
 Midwest/Diamond/Austro people have a lot knowledge and experience, since
 there are more than 500 AE50R engines ("Half Nortons") flying.

 My experiences about Wankels and Norton are only one year old. We have a
 team (3 men) flying a Beaver RX650 ultralight with Norton Aerotor80 P62 here
 in Finland. This plane was built in 1991, but has flown only 112 hours, of
 which 18 hours this year, in our use after some years of silence. The engine
 itself is powerful and has been running nicely. We only had to rebuild the
 fuel lines and electrical lines, because these were already 20 years old and
 caused some trouble. There is also another Norton Aerotor80 P62 here in
 Finland, which was spoiled long time ago because of poor oil. (In pieces in
 our garage waiting for rebuild?). These 2-rotor Norton Wankels are not many
 in the world, but it would be nice to keep them running and challenge the
 piston engines. Do You have any idea how to find the owners of these Norton
 Aerotor engines?

 Thanks to this "Rotary Engine" forum of Mr. Lamar, we have been able to
 receive some good advice from Norton&Wankel experts concerning the right oil
 type (Silkolene Comp2 Premix) and spark plugs (NGK CR9EK). Those old oil
 types and spark plugs, recommended by Norton some time early 90's, have not
 been available for a long time. If You Rich still have some old Norton spare
 plugs, I would be interested (maybe some other Norton lovers, too!).
 (Champion UG80PV or similar? Bosch plugs). Even some other spare parts, if
 they are available?

 BTW, I saw an article in Sport Pilot/ Hot kits & Homebuilts (September
 1995). There was a Tiger Moth replica with this type of a Norton Aerotor
 engine. I wonder, if this plane/engine is still flying or anybody knows
 anything about this?

 Enclosed: Some photos of these two Norton Aerotor 80 P62 engines, which we
 have here in Finland.

 Heikki


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.