Is there any reason I can't put the oil filter between the oil pump and
oil cooler?
That way I can mount the filter on the firewall and use a large one along
with an oil accumulator since my oil pan is so small. Heat might be an
issue.
Doug in Japan
No I think that will work. The pressure the oil cooler sees will
be reduced somewhat. I have no record of anybody doing that before.
BTW every time you pump oil through a right angle at high flow rate
you add heat to the oil and reduce the pressure. You can eliminated
two of them by taking oil directly out of the front end housing.
This is a Lyn Hanover modification. Rumor has it it will reduce
the oil temp by 10 or 20 F. Use a straight thread tap and O ring
fitting. A pipe tap could crack the front housing.
Paul Lamar
Hi Doug;
Filtering before the oil cooler is preferable if the cooler can handle
the pressure - you probably want at least 150 psi rated for cold
northern starts.
Look at 3rd gen or Rx8 coolers.
For oil filters, Lynn explicitly recommended against certain brands such
as fram (that is another topic)
I believe he also recommended synthetic straight weight 40 weight oil in
the sump + 2stroke pre-mix in the fuel, unless you fly in the frigid
northern climates in winter like here.
Cheers
Cary
snips....
I don't see anything in my notes about recommended filters. I would
appreciate a suggestion.
Doug in Japan
snips............
I forgot to mention that new oil inlets such as #2 (in particular) in
the engine pictures above have very little meat on Rx7 13B's. Plenty on
12A's. Haven't done the mod on RX8s. RX7 13B's required a bottoming
tap to get enough usable threads.
Cheers
Cary
-----------------------------------------------------------------
I would stick with Setrabe oil coolers as we have had oil coolers
from other suppliers split and in one or two cases cause an inflight
fire. I know these Setrabs work. Don't cut corners on this by using
coolers designed for other purposes. The engineers know what they
are doing. One of the big issues is the heat transfer rate from
the oil to the metal. Low viscosity oils cool better.
Paul Lamar
Wix used to be a division of Dana Corp in Toledo Ohio. And may still be.
Makers of thousands of products for the automotive and truck industry. Wix
and Champion make most of the aftermarket oil filters. That is, store or
house brands like STP and the like. They are also sold as WIX filters by
NAPA.
Champion also makes filters for airplane engines. All oil filter companies
fill their catalogs with each others filters. Those big filter catalogs do
not mean that every company makes thousands of different filters for every
known application. All the way up to truck air elements that your kids
could hide in. Of course they test each others filters as well. Everyone
has
water separators for diesel powered trucks, but generally Facet make almost
all of those, even though every catalogue has those filters under dozens of
part numbers. The Wix promotional kit used to be a cut open Fram PH8A and a
cut open Wix 51515 both the fit everything Ford for years and years and
most filter stands. The Fram had 104 square inches of paper and the Wix had
316 square inches of paper. I blew a Fram off of the filter stand on my
racer one day and damn near lost my racer and the shop.
The crimp at the top of the can unrolled. That was about 100 PSI on a warm
summer day. The Wix can is rated at 350 PSI. The K&N is 550 PSI. One
element should be enough, but call up the tech guys at K&N to be sure on the
flow rate. Do not say "airplane" during your conversation.
The Setrabs have never failed me. I once place a potato chip looking
Setrab between two pieces of plywood and ran over it with my van to
straighten
it out. It finished out the season with no leaks.
One advantage of the oil out location in line with the pump, in the front
iron, is that you can plug the gallery in front of the "O" ring junction
that Mazda should have eliminated years ago. All of the fixes involve a
thicker gasket or "O" ring protector to add pressure to the junction. The
front
cover has no bolt or stud close to the junction and the cover is flexible
and under startup cold oil pressure the cover is pushed forward and allows
the "O" ring to escape. The deformed section of the "O" ring then is
trapped
between the iron and front cover, holding the junction open, and most oil
pressure is lost. About 30 PSI is all that you will see if this happens.
Starting up with no prop (or load to limit RPM) or in very cold weather
with straight weight oil. There was a relief plunger in the circuit just
ahead of this junction that should prevent this problem but it is set at 140
PSI
and that is a bit higher than useful.
The "Banjo" fitting into the rear iron is a flow disaster and FEMA should
send out AN fittings to replace it.
Lynn E. Hanover
Does the rotary need an oil/air separator?
Jay
Nothing external as long as you make a deeper custom pan for the RX8
version. The rest of them including the 3 rotor usually use a top
on the custom pan with a few holes in it. Many of the rest use the
stock pan.
Here are some jpg's. On the subject.
Paul Lamar
Thanks Paul,
I'm using the stock pan on my 20B. Since it's not deeper/custom should I use
an external separator? If so where would you put it?
Oh and I just remembered. There is a small tube on the top of my oil filler
tube. Looks like a rubber hose attached to it originally. Any idea where
that hose should be routed?
Jay
I think the stock oil pan will work fine.
Unless you are doing aerobatics a race car puts far more stress
on the oil pick up system than an aircraft. Your main worry
will be adequate oil cooling as one third of total rotary engine cooling is
done by the oil. Low viscosity 5 weight synthetic oil helps greatly.
Do you have my book "How to Cool Your Wankel"?
The tube out of the filler neck usually is routed to the intake
manifold to re cycle the oil vapor. It will then help to lube the
apex seals.
When the engine is first started there will be some steam
as the water condensation inside the engine will vaporise
when the oil reaches 212 F.
If you object to that you could route it over board or to
a large transparent can and let it condense to water and oil.
A visual inspection of the can will tell you what is going on.
The water should settle to the bottom.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.