Hi Everyone,
Firstly thank you for letting me into your world.
My name is Keith (41) and I live In South Australia.
I was wondering if anyone could help me..
I'm just going through flying school and have appox 22 hours ... I am
looking at
building a kit plane. The plane I'm looking at is a Morgans Aeroworks
Sierra
100. As the build seems very simply... and at AU$24,500 for the basic
Kit
seems reasonably priced.
http://www.morganaeroworks.com.au/sierra100.html
With a Jabiru 6 cylinder engine 120HP, empty weight is about 313kg (690
lbs)
With a M TOW of 544kg (1200lbs) for LSA class.
Details of Jabiru 3300 engine 83.5 kg (178 lbs) complete including
exhaust,carburetor, starter motor, alternator and ignition system....
http://www.jabiru.net.au/
Is it possible to install a rotary to meet this criteria? (Possible a
single
rotor version.....)
Any Ideas or help or comments would be appreciated.
Keith
As I recall the Jabiru 6 cylinder engine 120HP is rated at 3300 RPM
which is not the same thrust as an AC engine rated at 2700 RPM.
Prop efficiency is down at 3300 RPM. Now a one rotor 120 HP Mazda would
be geared to run the prop at 2700 RPM. However 178 pounds all up for
the engine alone is hard to beat. You would need aluminum end housings
to get in that ball park with a Mazda. If you can wait awhile the
AIXRO Wankel kart engine manufacturer is coming out with a two
rotor version at around 100 HP that should be near ideal for that
category of light sport air craft.
Since the time to build is not much longer
for something bigger, faster and more powerful I would go bigger.
Then you can use a much cheaper and more powerful Mazda 2 rotor.
I suspect there would be little difference in the kit price.
In that case you would get a faster airplane which is very
important if we are talking cross country. Australia is a large
country. You need a faster airplane. I know because I have flown
all over the interior.
Paul Lamar
My first post and probably don't know what I am doing so sorry if in the
wrong format or cropping or whatever.
I am also in S.A.
I am in Summertown in the Adelaide Hills.
Also learning to fly power (at Parrafield).
I must be mad doing that but that is another story.
I learnt to fly in a glider in 1976 and have been an instructor since 1982.
Also a ground engineer in Gliding since 1980 and now hold basically all the
ratings required including major repair composite and major overhaul all
engine types (except rotary which will be interesting as I am embarking on a
project involving exactly that). Things are a bit different here and even
experimental aircraft have to have annuals by qualified people under the
Gliding Federation of Australia. It is run differently to GA.
Paul you continue to surprise me with the breadth of experience both in
engineering and life.
I have toured much of OZ and the interior or as we also say, the centre,
extensively in our Motor Glider. My wife is a wonderful co pilot and
organizer so we work well traveling.
The one thing I will disagree with Paul on is the need for speed.
We travel extensively in our H36 Dimona at 90KTS but with long legs as we
burn 12 Litres an hour and the tank has 79 liters usable.
I have attached a photo of my wife and our toy at a location Paul will
recognize. My darling is great at helping with tie down and covers etc.
This aircraft was one of 3 that my Darling and a friend and myself with help
from the kids restored from basically wrecks over a period of 14 months
which was full time for the friend and myself.
The current project is a HK36 Dimona which we bought of the insurance company
that covered it.
It was parked really badly in a tidal creek bed (also attached) and I didn't
pay much but it was insured for 140K before impact. It had a Rotax 100HP and
is also certified for the 115 HP.
Both versions are rated to tow Gliders.
My plan is put in a Rotary and it will tow a heap better than 115HP.
Weight however is a bit of an issue which I am working my way through.
As I mentioned things work a bit different here in Gliding with Experimental
category and am working with an engineer recognized by our version of the
FFA to get through the type acceptance quagmire.
Good luck Keith with your project. We may well have the opportunity to share
experience.
I agree with Paul regards building something a bit bigger if you are talking
GA experimental. The world is your oyster in choices.
Cheers.
Nige.
Yep been to Birdsville. I tried to get a Aussie security clearance in 2008 so I
could use my Aussie ticket and rent an airplane again. I could not get the red
tape negoited in time so we had to drive everywhere. We were in Adelaid in Feb
2008 via the coast road and wanted to rent a motor home to drive the 1100 K
Nullarbor to Perth for the adventure. We could not find anything small enough we
could afford so we flew commercial to Perth. My wife Robin is a retired TWA &
UAL A&P. One of the few females in that occupation. I married her so she could
legally fix my C182 :) That is why we can travel so cheaply. Australia is my
favorite destination. We still have a lot to explore.
The big advantage of the stock 2 rotor Mazda rotary is the low cost. A one rotor
actually cost more as you need a custom e-shaft and balance weights.
No other engine so suitable for aircraft use is anywhere near the low cost.
Especially if in the remote chance it needs overhaul.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.