Subject: Prop shaft metal selection Att. Jeff. Continued
From: Rotary Engine
Date: 12/3/2010, 3:25 PM
To: AAA Put this in the To box


   Lots of snips.

    To reduce shaft weight and minimize cost would it be practical to
   shrink
    fit
    an interior sleeve in the prop shaft end(s) (all parts annealed)
   and then
    bore and thread near the parting line? Will the bolt threads change too
    much
    after HT and grinding for bearing ID? Or, is it more practical to bore
    thicker wall to the ID shape?

    Dan F

    Jean,


    I see your dilemma. You want to reduce part count and eliminate
   having a
    bolt on connection to the planetary gear carrier. Your challenge
   then is
    basically cost and access to the interior boring operations.
   Usually, but
    not always, more modular construction is cheaper in mass production. A
    flanged bolt on connection to the planetary set carrier would prove
   to be
    the cheapest way to go. Paul has done an illustration with this concept
    before. Actually that is what the Bell 47 does. The internal spline
   plate
    in the photo middle far left bolts to the planetary carrier lower
   center.
    Notice the six bolt holes around the outer side. Another round
   plate (not
    pictured) bolts to the inner circle of the splined plate to catch the
    locking nut on the prop shaft that protrudes through. The spline
    connection
    plate rests against the main 3" ID outer bearing. The three inch shaft
    makes up for the fact that the unit is rather short coupled. That
   is the
    distance between the inner bearing and the outer bearing is less
   than four
    inches.

    With your gear set of choice, I would consider Dan's above advice, that
    is, press in the interior sleeve to carry the bearing after all
   internal
    boring is finished. Putting a small step in that internal bearing seat
    area
    will insure the sleeve is positioned accurately. Doing it this way the
    lathe
    operations are pretty straight forward and less expensive.

    Cheers

    Doug in Japan

    Here are some illustrations on the subject.

    Paul Lamar

    Paul,

    Those weren't the illustrations I was thinking about. I believe you
   have
    one that has an internally flanged prop shaft. The bolts screw into the
    planet carrier housing.

    Doug in Japan

    You will have to narrow it down more than that. How about a sketch?
    Most of my bolt on flange designs rely on the shear strength
    of the bolts. Same as the old Power Sport design. That is where
    I got the idea. I figure if it worked for them it will work
    for me :) Some types of bolts have enormous strength.


    Paul Lamar



    Doug

    I wasn't very clear on what I had in mind. The insert is intended to
    eliminate interior shaft machining - the bolt holes will be partly
   in the
    tube wall (say 1/3 of bolt dia) and 2/3 dia in the insert. The
   shrink fit
    and threads hold the parts together. Then machine the tube outside to
    attain wall thickness and bearing journal dia. Will this work? For
   a 6.5
    B single rotor how about 8 .25-24 bolts with 4 locater bushings at each
    end?
    (larger bolts for a 13 B) :)

    Dan F



    Dan, f

    Perhaps it wasn't your intention but you did give me an idea on how to
    make my
    prop shaft easier. Thanks for the inspiration. I will now machine a
   step
    into
    the inner part of two inch dia. shaft bore and stick the inner bearing
    there.
    OD of shaft is about 3". Now if I can find a thick, forged tube 6" inch
    OD,
    with a 2" ID I will have saved a lot of boring (literally) work.

    Now for your idea. Can it be done? Sure. Is it a strong joint? Sorry I
    don't think so. Bear in mind I am not an expert machinist but through
    experience I have found a round pipe or round bar that comes from the
    manufacturer is never round. Machining is necessary to get a good
   fit. For
    interference fits, excellent machining holding close tolerances is
    mandatory.

    As I understand your idea, drilling and tapping holes at the
   insert/ tube
    joint line and expecting it to hold the insert and rotating parts
   together
    is
    risky. Even if the insert was welded in you would still have, in
   effect,
    two
    man-made fracture lines running longitudinally through each thread. In
    effect
    there would be a series of short radian threads. The thread loses its
    integrity
    and it's holding power diminishes in unpredictable manner over time
   as the
    insert micro flexes. The bolts as you mentioned would also have to
   absorb
    torsional forces. Even if the upper bore hole was counter sunk, the
    rotating
    forces would widen the gap in the joint line weakening the thread even
    more.

    As you probably know there are rotating engine parts where a bolt
   appear
    to do
    double duty. Notice how a clutch plate is attached to the flywheel.
   Logic
    would suggest the bolts are seeing some torsional force but the
   frictional
    footprint of the mating surfaces is so large the torsional forces are
    miniscule.
    And that is one key to good design. Flat accurate interfaces
   between the
    mating surfaces .

    Doug in Japan.

    Doug the secret to handling large bar stock is finding a really
    big lathe and large drills. Shops with these tools can drill
    a 3 inch hole in just a few minutes. Surely there is a ship
    yard in Tokyo bay some place.


    Paul Lamar


    Hi Doug

    Look this supplier does have 6"dia aluminum with 2"wall

    http://www.vitaneedle.com/aluminum-tube.htm



    Jean Prudhomme

    Jean,

    Thanks, for the info.  I have no need for an alumnium tube though
   since I
    already  have a cast magnesium bell 47 gear housing, and an inner
   modified
    RX-4 aluminum bell housing.  I am just looking to make up  the prop
   shaft.

    I found a source for forged round bar 4340 steel, which unless someone
    convinces me it is over kill I'll go with it.

    Paul I can drill a two inch hole on the lathes I have access to.  I
   have to
    do it in stages though starting  with a 10mm  pilot hole and slow feed.

    Doug in Japan


   6" aluminum pipe with a 2" wall; from a company called  VitaNeedle;
   which
   specializes in needles.

   Begs the question "What ya gonna stick with that needle!!!"  :) )

    brian gochnauer

   Search your email program help on how to add a signature
   to your email brian,

   Paul Lamar

Gee; I thought it was automatic; it kept showing up automatically. :)

BrianG

No I was doing it.

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.