Subject: Prop shaft metal selection Att. Jeff.
From: Rotary Engine
Date: 12/3/2010, 12:27 AM
To: AAA Put this in the To box




Paul
I can purchase round metal to machine my prop shaft and the material
available by the inch is the 8620 cold roll steel.
I will machine the shaft myself and have the splines made it by
outside shop.
I do have an alternative ,built the shaft with the planet driven by
outher splines or built the shaft complete with the planet housing
and it will be in one pce,the price for material difference is $50.00
but more milling machining for the pinions cages.
I wondering if Jeff can do the milling parts
9" long 4.25"dia is $124.00
8" 3.75"dia is $72.00
I bought a 9"x 24 lathe from Harbor Freight and i should have it soon

There is the 8620 specs;

8620 Cold Roll Steel

Analysis
Mechanical Properties
Applications
Machineability and Weldability
Heat Treating
Tolerances
Speedy Metals items
AISI 8620 is an alloy carburizing steel when thermally treated
develops a hard outer case with a soft ductile core. Carefully
controlled proportions of chromium, nickel and molybdenum are
responsible for the extensive use as a carburizing alloy steel,
with valuable features including extreme surface hardenability
and good internal strength. Has minimum distortion and growth
characteristics. 8620 has good machinability and responds well to
polishing.
ANALYSIS

Carbon (C)
Manganese (Mn)
Silicon (Si)
Chromium (Cr)
Nickel (Ni)
Molybdenum (Mo)
Phosphorus (P)
Max
Sulfur (S)
Max

18-0.23
0.7-0.9
0.15-0.35
0.4-0.6
0.4-0.7
0.15-0.25
0.035
0.04
8620 cold roll bars conforms to ASTM A331
MECHANICAL PROPERTIES

Condition
Tensile Strength (PSI)
Yield Strength (PSI)
Reduction of Area
Elongation in 2"
Brinell Hardness

Annealed
100,000
85,000
60
21
185

APPLICATIONS
8620 applications include gears, pinions, cams, cranks,
clutch shafts, shafting, axles, tie bars, collets, bushings,
heavy duty pins, bolting, springs, hand tools, die cases,
and a multitude of machinery parts and components.
MACHINEABILITY AND WELDABILITY

8620 has a machinability rating at 66% of B1112. Average cutting
speed 127 ft/min.
8620 can be forged at 2200° down to 1800° F prior to hardening or
carburizing.
8620 is excellent for welding applications

HEAT TREATING
8620 can be hardened to 1500° F followed by water quench. Carburize
at 1650° - 1700° F in an appropriate carburizing medium and oil
quench to harden. Tempering of carburized parts is done at 250° - 300° F
and will result in the alloy having a core strength of approximately
135,000 psi minimum. Tempering of heat treated and water quenched
parts (not carburized) is done at 400° - 1300° F, with greater
hardness the lower the tempering temperature.
TOLERANCES

Rounds

Up to 1-1/2" incl.
-.002

Over 1-1/2 to under 2-1/2
-.003

Over 2-1/2 to 4" incl.
-.004

SPEEDY METALS ITEMS

3/8" {A} Rd Cold Finished 8620
1/2" {A} Rd Cold Finished 8620
5/8" {A} Rd Cold Finished 8620

11/16" {A} Rd Cold Finished 8620
3/4" {A} Rd Cold Finished 8620
7/8" {A} Rd Cold Finished 8620

1" {A} Rd Cold Finished 8620
1-1/8" {A} Rd Cold Finished 8620
1-1/4" {A} Rd Cold Finished 8620

1-3/8" {A} Rd Cold Finished 8620
1-1/2" {A} Rd Cold Finished 8620
1-5/8" {A} Rd Cold Finished 8620

1-3/4" {A} Rd Cold Finished 8620
1-7/8" {A} Rd Cold Finished 8620
2" {A} Rd Cold Finished 8620

2-1/8" {A} Rd Cold Finished 8620
2-1/4" {A} Rd Cold Finished 8620
2-3/8" {A} Rd Cold Finished 8620

2-1/2" {A} Rd Cold Finished 8620
2-5/8" {A} Rd Cold Finished 8620
2-3/4" {A} Rd Cold Finished 8620

2-7/8" {A} Rd Cold Finished 8620
3" {A} Rd Cold Finished 8620
3-1/4" {A} Rd Cold Finished 8620

3-1/2" {A} Rd Cold Finished 8620
3-3/4" {A} Rd Cold Finished 8620
4" {A} Rd Cold Finished 8620

4-1/4" {A} Rd Cold Finished 8620
4-1/2" {A} Rd Cold Finished 8620
4-3/4" {A} Rd Cold Finished 8620

5" {A} Rd Cold Finished 8620
5-1/2" {A} Rd Cold Finished 8620
6" {A} Rd Cold Finished 8620


Jean Prudhomme

-----------------------------------------
Jeff is on here so I think he will answer.

Paul Lamar


Jean,

Good information. Thanks, I was considering chrome moly 4130 for
the same application but was not happy about the way it machines.
I am interested in purchasing a chunk of 6 inch round by about 8
inches long. My thinking, is to have the six inch prop flange on the
outer size machined down to the outer seal step, and then reduced down
the 3 inch dia. bearing step and finally machine the inner spline. On
the Bell PSRU the forged planet gear housing has a female spline plate
that is bolted to it. Like Mistral's design I will have the Prop
shaft necked down after the spline and threaded to accommodate a 52mm
Hex nut. This nut locks the unit together The most inner partt of the
shaft reduces down to about 20mm and rides in the inner bearing. The
inside of the bar will be bored out to lighten it up. For maximum
toughness I would prefer starting with a forged bar though. If you or
anyone else is thinking the same way I would be willing to go in on a
group buy of material. Any info on a forged piece?

Doug in Japan


Doug

Just read your request....sounds interesting..I can help if you want,
let me know.............

BTW 4130 is not difficult to machine annealed, choose the best material
for the application.......

jeff

Jeff is right, you may wish to use annealed 4140 tubing, HT to Rc 60 or
so.
milo

Jean,


Please tell me how you would attach the prop flange. Taper or key way?
Both? I
assume the inner piece is threaded.

Doug in Japan

Doug
The flange have big splines and will be hold by threaded nuts with large
flange and tighted with hight torque by bolting the flange on long pce of
flat metal to hold it at torquing time..
At the end of splines on prop flange i design a taper who will meet the
one
one prop shaft.
An o ring will be located between the propshaft and the flange nut.

For bearing lubrication i will machine a passageway on the housing for
feeding and oil return under the mid sleeve bushing and the mid sleeve
bearing will be pressure fit before final i.d. size machining
I know my housing will not fit Jeff plate holes but it will be much
stronger the fact a constant speed will be driven and the front housing is
available true Speedway engineering.

The aluminum housing will be close to tracy weight might be a 1 or 2lbs
at
the most but i try to get lighter as possible.
With the 2 parts housing it will be much more accurate to lock the ring
gear before final assembly.

I had a bearing on the sungear shaft at the seal location but it can be
built without it but i prefer adding a roller or ball bearing at this
position.
I did several assembly design to obtain the best configuration and i am at
the stage to details all parts.
I do have an estimate for all bearings and it is close to $400 and i still
searching for better price.


Jean Prudhomme



To reduce shaft weight and minimize cost would it be practical to shrink
fit
an interior sleeve in the prop shaft end(s) (all parts annealed) and then
bore and thread near the parting line? Will the bolt threads change too
much
after HT and grinding for bearing ID? Or, is it more practical to bore
thicker wall to the ID shape?

Dan F

Jean,


I see your dilemma. You want to reduce part count and eliminate having a
bolt on connection to the planetary gear carrier. Your challenge then is
basically cost and access to the interior boring operations. Usually, but
not always, more modular construction is cheaper in mass production. A
flanged bolt on connection to the planetary set carrier would prove to be
the cheapest way to go. Paul has done an illustration with this concept
before. Actually that is what the Bell 47 does. The internal spline plate
in the photo middle far left bolts to the planetary carrier lower center.
Notice the six bolt holes around the outer side. Another round plate (not
pictured) bolts to the inner circle of the splined plate to catch the
locking nut on the prop shaft that protrudes through. The spline connection
plate rests against the main 3" ID outer bearing. The three inch shaft
makes up for the fact that the unit is rather short coupled. That is the
distance between the inner bearing and the outer bearing is less than four
inches.

With your gear set of choice, I would consider Dan's above advice, that
is, press in the interior sleeve to carry the bearing after all internal
boring is finished. Putting a small step in that internal bearing seat area
will insure the sleeve is positioned accurately. Doing it this way the lathe
operations are pretty straight forward and less expensive.

Cheers

Doug in Japan

Here are some illustrations on the subject.

Paul Lamar

Paul,

Those weren't the illustrations I was thinking about. I believe you have
one that has an internally flanged prop shaft. The bolts screw into the
planet carrier housing.

Doug in Japan

You will have to narrow it down more than that. How about a sketch?
Most of my bolt on flange designs rely on the shear strength
of the bolts. Same as the old Power Sport design. That is where
I got the idea. I figure if it worked for them it will work
for me :) Some types of bolts have enormous strength.


Paul Lamar



Doug

I wasn't very clear on what I had in mind. The insert is intended to
eliminate interior shaft machining - the bolt holes will be partly in the
tube wall (say 1/3 of bolt dia) and 2/3 dia in the insert. The shrink fit
and threads hold the parts together. Then machine the tube outside to
attain wall thickness and bearing journal dia. Will this work? For a 6.5
B single rotor how about 8 .25-24 bolts with 4 locater bushings at each end?
(larger bolts for a 13 B) :)

Dan F



Dan, f

Perhaps it wasn't your intention but you did give me an idea on how to make my
prop shaft easier. Thanks for the inspiration. I will now machine a step into
the inner part of two inch dia. shaft bore and stick the inner bearing there.
OD of shaft is about 3". Now if I can find a thick, forged tube 6" inch OD,
with a 2" ID I will have saved a lot of boring (literally) work.

Now for your idea. Can it be done? Sure. Is it a strong joint? Sorry I
don't think so. Bear in mind I am not an expert machinist but through
experience I have found a round pipe or round bar that comes from the
manufacturer is never round. Machining is necessary to get a good fit. For
interference fits, excellent machining holding close tolerances is mandatory.

As I understand your idea, drilling and tapping holes at the insert/ tube
joint line and expecting it to hold the insert and rotating parts together is
risky. Even if the insert was welded in you would still have, in effect, two
man-made fracture lines running longitudinally through each thread. In effect
there would be a series of short radian threads. The thread loses its integrity
and it's holding power diminishes in unpredictable manner over time as the
insert micro flexes. The bolts as you mentioned would also have to absorb
torsional forces. Even if the upper bore hole was counter sunk, the rotating
forces would widen the gap in the joint line weakening the thread even more.

As you probably know there are rotating engine parts where a bolt appear to do
double duty. Notice how a clutch plate is attached to the flywheel. Logic
would suggest the bolts are seeing some torsional force but the frictional
footprint of the mating surfaces is so large the torsional forces are miniscule.
And that is one key to good design. Flat accurate interfaces between the
mating surfaces .

Doug in Japan.

Doug the secret to handling large bar stock is finding a really
big lathe and large drills. Shops with these tools can drill
a 3 inch hole in just a few minutes. Surely there is a ship
yard in Tokyo bay some place.


Paul Lamar

                       
Hi Doug

Look this supplier does have 6"dia aluminum with 2"wall

http://www.vitaneedle.com/aluminum-tube.htm



Jean Prudhomme

Jean,

Thanks, for the info.  I have no need for an alumnium tube though since I already  have a cast magnesium bell 47 gear housing, and an inner modified RX-4 aluminum bell housing.  I am just looking to make up  the prop shaft.

I found a source for forged round bar 4340 steel, which unless someone convinces me it is over kill I'll go with it.

Paul I can drill a two inch hole on the lathes I have access to.  I have to do it in stages though starting  with a 10mm  pilot hole and slow feed.

Doug in Japan


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.