Subject: Prop shaft metal selection Att. Jeff.
From: Rotary Engine
Date: 12/3/2010, 8:28 AM
To: AAA Put this in the To box


 Paul
 I can purchase round metal to machine my prop shaft and the material
 available by the inch is the 8620 cold roll steel.
 I will machine the shaft myself and have the splines made it by
 outside shop.
 I do have an alternative ,built the shaft with the planet driven by
 outher splines or built the shaft complete with the planet housing
 and it will be in one pce,the price for material difference is $50.00
 but more milling machining for the pinions cages.
 I wondering if Jeff can do the milling parts
 9" long 4.25"dia is $124.00
 8" 3.75"dia is $72.00
 I bought a 9"x 24 lathe from Harbor Freight and i should have it soon

 There is the 8620 specs;

 8620 Cold Roll Steel

 Analysis
 Mechanical Properties
 Applications
 Machineability and Weldability
 Heat Treating
 Tolerances
 Speedy Metals items
 AISI 8620 is an alloy carburizing steel when thermally treated
 develops a hard outer case with a soft ductile core. Carefully
 controlled proportions of chromium, nickel and molybdenum are
 responsible for the extensive use as a carburizing alloy steel,
 with valuable features including extreme surface hardenability
 and good internal strength. Has minimum distortion and growth
 characteristics. 8620 has good machinability and responds well to
 polishing.
 ANALYSIS

 Carbon (C)
 Manganese (Mn)
 Silicon (Si)
 Chromium (Cr)
 Nickel (Ni)
 Molybdenum (Mo)
 Phosphorus (P)
 Max
 Sulfur (S)
 Max

 18-0.23
 0.7-0.9
 0.15-0.35
 0.4-0.6
 0.4-0.7
 0.15-0.25
 0.035
 0.04
 8620 cold roll bars conforms to ASTM A331
 MECHANICAL PROPERTIES

 Condition
 Tensile Strength (PSI)
 Yield Strength (PSI)
 Reduction of Area
 Elongation in 2"
 Brinell Hardness

 Annealed
 100,000
 85,000
 60
 21
 185

 APPLICATIONS
 8620 applications include gears, pinions, cams, cranks,
 clutch shafts, shafting, axles, tie bars, collets, bushings,
 heavy duty pins, bolting, springs, hand tools, die cases,
 and a multitude of machinery parts and components.
 MACHINEABILITY AND WELDABILITY

 8620 has a machinability rating at 66% of B1112. Average cutting
 speed 127 ft/min.
 8620 can be forged at 2200° down to 1800° F prior to hardening or
 carburizing.
 8620 is excellent for welding applications

 HEAT TREATING
 8620 can be hardened to 1500° F followed by water quench. Carburize
 at 1650° - 1700° F in an appropriate carburizing medium and oil
 quench to harden. Tempering of carburized parts is done at 250° - 300° F
 and will result in the alloy having a core strength of approximately
 135,000 psi minimum. Tempering of heat treated and water quenched
 parts (not carburized) is done at 400° - 1300° F, with greater
 hardness the lower the tempering temperature.
 TOLERANCES

 Rounds

 Up to 1-1/2" incl.
 -.002

 Over 1-1/2 to under 2-1/2
 -.003

 Over 2-1/2 to 4" incl.
 -.004

 SPEEDY METALS ITEMS

 3/8" {A} Rd Cold Finished 8620
 1/2" {A} Rd Cold Finished 8620
 5/8" {A} Rd Cold Finished 8620

 11/16" {A} Rd Cold Finished 8620
 3/4" {A} Rd Cold Finished 8620
 7/8" {A} Rd Cold Finished 8620

 1" {A} Rd Cold Finished 8620
 1-1/8" {A} Rd Cold Finished 8620
 1-1/4" {A} Rd Cold Finished 8620

 1-3/8" {A} Rd Cold Finished 8620
 1-1/2" {A} Rd Cold Finished 8620
 1-5/8" {A} Rd Cold Finished 8620

 1-3/4" {A} Rd Cold Finished 8620
 1-7/8" {A} Rd Cold Finished 8620
 2" {A} Rd Cold Finished 8620

 2-1/8" {A} Rd Cold Finished 8620
 2-1/4" {A} Rd Cold Finished 8620
 2-3/8" {A} Rd Cold Finished 8620

 2-1/2" {A} Rd Cold Finished 8620
 2-5/8" {A} Rd Cold Finished 8620
 2-3/4" {A} Rd Cold Finished 8620

 2-7/8" {A} Rd Cold Finished 8620
 3" {A} Rd Cold Finished 8620
 3-1/4" {A} Rd Cold Finished 8620

 3-1/2" {A} Rd Cold Finished 8620
 3-3/4" {A} Rd Cold Finished 8620
 4" {A} Rd Cold Finished 8620

 4-1/4" {A} Rd Cold Finished 8620
 4-1/2" {A} Rd Cold Finished 8620
 4-3/4" {A} Rd Cold Finished 8620

 5" {A} Rd Cold Finished 8620
 5-1/2" {A} Rd Cold Finished 8620
 6" {A} Rd Cold Finished 8620


 Jean Prudhomme

 -----------------------------------------
 Jeff is on here so I think he will answer.

 Paul Lamar


 Jean,

 Good information. Thanks, I was considering chrome moly 4130 for
 the same application but was not happy about the way it machines.
 I am interested in purchasing a chunk of 6 inch round by about 8
 inches long. My thinking, is to have the six inch prop flange on the
 outer size machined down to the outer seal step, and then reduced down
 the 3 inch dia. bearing step and finally machine the inner spline. On
 the Bell PSRU the forged planet gear housing has a female spline plate
 that is bolted to it. Like Mistral's design I will have the Prop
 shaft necked down after the spline and threaded to accommodate a 52mm
 Hex nut. This nut locks the unit together The most inner partt of the
 shaft reduces down to about 20mm and rides in the inner bearing. The
 inside of the bar will be bored out to lighten it up. For maximum
 toughness I would prefer starting with a forged bar though. If you or
 anyone else is thinking the same way I would be willing to go in on a
 group buy of material. Any info on a forged piece?

 Doug in Japan


 Doug

 Just read your request....sounds interesting..I can help if you want,
 let me know.............

 BTW 4130 is not difficult to machine annealed, choose the best material
 for the application.......

 jeff

 Jeff is right, you may wish to use annealed 4140 tubing, HT to Rc 60 or
 so.
 milo

 Jean,


 Please tell me how you would attach the prop flange. Taper or key way?
 Both? I
 assume the inner piece is threaded.

 Doug in Japan

 Doug
 The flange have big splines and will be hold by threaded nuts with large
 flange and tighted with hight torque by bolting the flange on long pce of
 flat metal to hold it at torquing time..
 At the end of splines on prop flange i design a taper who will meet the
 one
 one prop shaft.
 An o ring will be located between the propshaft and the flange nut.

 For bearing lubrication i will machine a passageway on the housing for
 feeding and oil return under the mid sleeve bushing and the mid sleeve
 bearing will be pressure fit before final i.d. size machining
 I know my housing will not fit Jeff plate holes but it will be much
 stronger the fact a constant speed will be driven and the front housing is
 available true Speedway engineering.

 The aluminum housing will be close to tracy weight might be a 1 or 2lbs
 at
 the most but i try to get lighter as possible.
 With the 2 parts housing it will be much more accurate to lock the ring
 gear before final assembly.

 I had a bearing on the sungear shaft at the seal location but it can be
 built without it but i prefer adding a roller or ball bearing at this
 position.
 I did several assembly design to obtain the best configuration and i am at
 the stage to details all parts.
 I do have an estimate for all bearings and it is close to $400 and i still
 searching for better price.


 Jean Prudhomme



 To reduce shaft weight and minimize cost would it be practical to shrink
 fit
 an interior sleeve in the prop shaft end(s) (all parts annealed) and then
 bore and thread near the parting line? Will the bolt threads change too
 much
 after HT and grinding for bearing ID? Or, is it more practical to bore
 thicker wall to the ID shape?

 Dan F

 Jean,


 I see your dilemma. You want to reduce part count and eliminate having a
 bolt on connection to the planetary gear carrier. Your challenge then is
 basically cost and access to the interior boring operations. Usually, but
 not always, more modular construction is cheaper in mass production. A
 flanged bolt on connection to the planetary set carrier would prove to be
 the cheapest way to go. Paul has done an illustration with this concept
 before. Actually that is what the Bell 47 does. The internal spline plate
 in the photo middle far left bolts to the planetary carrier lower center.
 Notice the six bolt holes around the outer side. Another round plate (not
 pictured) bolts to the inner circle of the splined plate to catch the
 locking nut on the prop shaft that protrudes through. The spline
connection
 plate rests against the main 3" ID outer bearing. The three inch shaft
 makes up for the fact that the unit is rather short coupled. That is the
 distance between the inner bearing and the outer bearing is less than four
 inches.

 With your gear set of choice, I would consider Dan's above advice, that
 is, press in the interior sleeve to carry the bearing after all internal
 boring is finished. Putting a small step in that internal bearing seat
area
 will insure the sleeve is positioned accurately. Doing it this way the
lathe
 operations are pretty straight forward and less expensive.

 Cheers

 Doug in Japan

 Here are some illustrations on the subject.

 Paul Lamar

 Paul,

 Those weren't the illustrations I was thinking about. I believe you have
 one that has an internally flanged prop shaft. The bolts screw into the
 planet carrier housing.

 Doug in Japan

 You will have to narrow it down more than that. How about a sketch?
 Most of my bolt on flange designs rely on the shear strength
 of the bolts. Same as the old Power Sport design. That is where
 I got the idea. I figure if it worked for them it will work
 for me :) Some types of bolts have enormous strength.


 Paul Lamar



 Doug

 I wasn't very clear on what I had in mind. The insert is intended to
 eliminate interior shaft machining - the bolt holes will be partly in the
 tube wall (say 1/3 of bolt dia) and 2/3 dia in the insert. The shrink fit
 and threads hold the parts together. Then machine the tube outside to
 attain wall thickness and bearing journal dia. Will this work? For a 6.5
 B single rotor how about 8 .25-24 bolts with 4 locater bushings at each
end?
 (larger bolts for a 13 B) :)

 Dan F



 Dan, f

 Perhaps it wasn't your intention but you did give me an idea on how to
make my
 prop shaft easier. Thanks for the inspiration. I will now machine a step
into
 the inner part of two inch dia. shaft bore and stick the inner bearing
there.
 OD of shaft is about 3". Now if I can find a thick, forged tube 6" inch
OD,
 with a 2" ID I will have saved a lot of boring (literally) work.

 Now for your idea. Can it be done? Sure. Is it a strong joint? Sorry I
 don't think so. Bear in mind I am not an expert machinist but through
 experience I have found a round pipe or round bar that comes from the
 manufacturer is never round. Machining is necessary to get a good fit. For
 interference fits, excellent machining holding close tolerances is
mandatory.

 As I understand your idea, drilling and tapping holes at the insert/ tube
 joint line and expecting it to hold the insert and rotating parts together
is
 risky. Even if the insert was welded in you would still have, in effect,
two
 man-made fracture lines running longitudinally through each thread. In
effect
 there would be a series of short radian threads. The thread loses its
integrity
 and it's holding power diminishes in unpredictable manner over time as the
 insert micro flexes. The bolts as you mentioned would also have to absorb
 torsional forces. Even if the upper bore hole was counter sunk, the
rotating
 forces would widen the gap in the joint line weakening the thread even
more.

 As you probably know there are rotating engine parts where a bolt appear
to do
 double duty. Notice how a clutch plate is attached to the flywheel. Logic
 would suggest the bolts are seeing some torsional force but the frictional
 footprint of the mating surfaces is so large the torsional forces are
miniscule.
 And that is one key to good design. Flat accurate interfaces between the
 mating surfaces .

 Doug in Japan.

 Doug the secret to handling large bar stock is finding a really
 big lathe and large drills. Shops with these tools can drill
 a 3 inch hole in just a few minutes. Surely there is a ship
 yard in Tokyo bay some place.


 Paul Lamar


 Hi Doug

 Look this supplier does have 6"dia aluminum with 2"wall

 http://www.vitaneedle.com/aluminum-tube.htm



 Jean Prudhomme

Jean,

Thanks, for the info.  I have no need for an alumnium tube though since I
already  have a cast magnesium bell 47 gear housing, and an inner modified
RX-4 aluminum bell housing.  I am just looking to make up  the prop shaft.

I found a source for forged round bar 4340 steel, which unless someone
convinces me it is over kill I'll go with it.

Paul I can drill a two inch hole on the lathes I have access to.  I have to
do it in stages though starting  with a 10mm  pilot hole and slow feed.

Doug in Japan


Doug

Ok, I will agree on the bolt situation.  http://www.factorysteel.com  has a
great selection of 4130 tubing, With a little machining of the planet
carrier and a 2.5 OD x .5 wall prop shaft these two parts will bolt together
very nicely - just have to remove about .312 interior wall thickness between
the bolt areas of the prop shaft.  I also am thinking of installing a
bearing in the end of the prop shaft to support the input shaft - only
concern is bearing skid and surface speed as the two turn opposite
directions.  In my case up to 8,000 rpm input and 2,524 rpm output (3.17
ratio).  How about a pressure fed plain bearing?  It will be a little hassle
to get engine oil there but only 3 additional parts and gun drill/cross
drill the input shaft.  Another advantage is the planet gears can be oiled
from the center by cross drilling the sun gear. Good or bad idea?

Dan F


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.