Subject: Low cost off the shelf parts for the Ellison
From: Rotary Engine
Date: 12/13/2010, 7:14 AM
To: AAA Put this in the To box


 http://tinyurl.com/28gc2bo
 http://www.tillotson.ie/
 This is going to save a pile of money
 making a dual Ellison for our P-ports.
 Some of the Ellison parts are bought
 from Tillotson. Brilliant idea on the
 part of Ellison. Cuts his cost enormously.
 Rotec is probabbly doing the same thing.
 I was going to use Holley parts but
 this is 1000% better.
 Paul Lamar
 -----------------------------------------------------
 Here is the latest 3D's.
 The stock ACRE slide throttle parts are used.
 The slide itself is modified for the brass tube
 with all tiny holes in it.
 The pressure regulator is a copy of the Ellison which
 uses stock Tillotson pressure regulator parts. Same
 as Ellison did.
 The pressure regulator is designed to bolt to the
 stock slide housing using the existing bolt holes.
 The fuel is fed into the center of the brass tube
 and then out to each runner.
 Craig, did you get a quote on the laser holes?
 Paul Lamar

 Paul,

 Could you Tig weld two Ellison tubes together? In the Tillotson
 drawing it shows a booster venturi. Would an annular discharge
 Holley booster work?

 Dale Davies

 Yes I think you could if you align them with an interior coupling
 tube. Since they are brass I would sweat solder them to the
 interior coupling tube.

 I found a mistake in the center feed so I had to move the
 regulator to the end. That means the laser hole size
 will be larger for rotor 2. Probably something like
 .012 instead of .010 to equalize the flow.

 I don't think you need a booster with the Ellison design.
 What the Ellison does is increase the fuel flow at high
 air flows by applying dynamic pressure to the back side
 of the diaphragm. In effect this raises the fuel pressure
 inside the regulator. Very tricky on the part of Ellison.

 Paul Lamar


 Hi Paul,
 I was thinking that if the holes in the tube were posing a problem,
the use of
 the Holley annular discharge booster could work as a replacement.

 Dale Davies

Good day,,

I'm assuming the Tillotson parts are from a HR series carb as Tillotson
website shows this as largest bore carb available.   Will the
diaphram "float" valve provide enough fuel flow at WO power setting?
Reason I'm asking is a single 1 3/8" HR carb is barely satisfactory for
a stock 400 cc two-cycle snowmobile motor.  A 1 5/8" series HD needed
for anything larger. Early to mid  70's Skidoo Rotax 440 / 640 / 775
cc twins usually had a single HD as did JLO, Sachs, and others of that
era. Skidoo racing sleds 440 cc and up needed  two. I spent some time in
my garage yesterday trying to locate a old HD carb to compare with HR
parts but not successful. My recollection HD regulator parts
proportionally larger. I'll look again today if need be.

BTW, the Tillotson carb crankcase pulsed diaphram fuel pump located
below the regulator ass'y is very reliable. Could be pulsed from intake
track I'm thinking if utilized. Excess fuel was returned to tank from a
bleed port helping prevent fuel heating and percolation.

Sincerely,

Al Koivisto

That aspect of it needs testing. The needle valve holding
the pump pressure may need to be enlarged. I'll know more
when I get the Tillotson needle valve and compare it with
the Ellison.

Do you know what the Tillotson pump can flow and the pressure
it generates?

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.