Subject: Low cost off the shelf parts for the Ellison
From: Rotary Engine
Date: 12/13/2010, 9:53 PM
To: AAA Put this in the To box



 http://tinyurl.com/28gc2bo
 http://www.tillotson.ie/
 This is going to save a pile of money
 making a dual Ellison for our P-ports.
 Some of the Ellison parts are bought
 from Tillotson. Brilliant idea on the
 part of Ellison. Cuts his cost enormously.
 Rotec is probabbly doing the same thing.
 I was going to use Holley parts but
 this is 1000% better.
 Paul Lamar
 -----------------------------------------------------
 Here is the latest 3D's.
 The stock ACRE slide throttle parts are used.
 The slide itself is modified for the brass tube
 with all tiny holes in it.
 The pressure regulator is a copy of the Ellison which
 uses stock Tillotson pressure regulator parts. Same
 as Ellison did.
 The pressure regulator is designed to bolt to the
 stock slide housing using the existing bolt holes.
 The fuel is fed into the center of the brass tube
 and then out to each runner.
 Craig, did you get a quote on the laser holes?
 Paul Lamar

 Paul,

 Could you Tig weld two Ellison tubes together? In the Tillotson
 drawing it shows a booster venturi. Would an annular discharge
 Holley booster work?

 Dale Davies

 Yes I think you could if you align them with an interior coupling
 tube. Since they are brass I would sweat solder them to the
 interior coupling tube.

 I found a mistake in the center feed so I had to move the
 regulator to the end. That means the laser hole size
 will be larger for rotor 2. Probably something like
 .012 instead of .010 to equalize the flow.

 I don't think you need a booster with the Ellison design.
 What the Ellison does is increase the fuel flow at high
 air flows by applying dynamic pressure to the back side
 of the diaphragm. In effect this raises the fuel pressure
 inside the regulator. Very tricky on the part of Ellison.

 Paul Lamar


 Hi Paul,
 I was thinking that if the holes in the tube were posing a problem,
 the use of
 the Holley annular discharge booster could work as a replacement.

 Dale Davies





Paul, I sketched something out in Rhino to have a look at it today.
Hopefully 3 files are attached. It is the tillotson controlled injector
spray bar. I chose the middle location for the mixture lever to use it
to join the two outboard tubes and give access to the full diameter of
the tube for fuel flow into each tube. This is to allow even pressure to
both rotor spray bars with the connector lever equalizing the flow. I
also stood the diaphragm control on edge to make it narrower and reduce
the bolt count to two. There are external sleeves around the spray tubes
to get a precision fit sealing the covered holes so that fuel will be
less likely to bypass the spray bar and "leak" into the intake as raw
fuel.

The sleeves attach to the slide with roll pins and the whole works
floats in a channel milled into the intake side of the slide with a ball
end mill. The length of the channel will not be to the ends of the slide
but only long enough to clear the spray tube as the slide travels. This
eliminates getting a hole drilled 10 inches through the slide
lengthwise. The barrel on the end of the lever has an external channel
with 4 feed holes to the center. The center is the diameter of the spray
bars for the first .375 inches from each end then steps down to the
internal diameter of the spray bar providing a depth stop when soldering
ate assorted brass pieces together. The seal sleeves are also brass for
consistent thermal expansion of the two telescoping parts.The lever is
drawn flat in this sketch but would actually have an offset to clear the
cable clevis.

The issues I had with the discussion to date were how to
prevent the spray bar covered holes from leaking without being so tight
in the slide that binding and breakage of the brass tube could occur.
Also while I have make gun drills in the past I don't have much
confidence in drilling that deep without chips jamming the bit, and the
alignment required looks really tedious.

I saw in a recent post you had a Karman Ghia. Mine were a 40 HP
red one for 4 years, then a 53 HP for five years repainted pine green at
trade in but I had a blue acetylene candy apple scheeme for the 178K
miles I drove it.Best car I ever drove in snow.

george grimes

I'll make the slide in 2 pieces to ease the drilling problem.
I think you missed a message or two.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.