Subject: aluminum/beryllium alloys???
From: Rotary Engine
Date: 12/21/2010, 3:28 PM
To: AAA Put this in the To box


Right now I am avoiding the intense rain here and am researching engine
stuff indoors.
I can easily mill the hole when I get ready, I have a couple expendable
housings that will work if the sweat is successful. IMS is down the
street if I need materials and I have a lot of that already. It's a
month or so down the road before I get into this particular project.

On a different note, I am learning how to do aluminum castings. I am
looking for the best casting material for center and end housings,
possibly one to the ceramic metal matrix hyper alloys and beralcast 363
for rotor material. It appears to be the only beryllium alloy on the
market and can be investment cast to near net. Do you have any knowledge
on this stuff? I've been reading about it for about a day, and looking
for a supplier.

Ed Carver

I have heard of aluminum/beryllium alloys .70% the density of aluminum.
Makes great rotors. What is the density of beralcast 363?

Paul Lamar



The spec related text is from the below link:

http://www.mdatechnology.net/techprofile.aspx?id=403

--

GENERAL BERALCAST�® ADVANTAGES


Advantages over Aluminum

* About 22 percent lower density with essentially equivalent
strength to A356 aluminum

* About 3 times stiffer (modulus of elasticity in tension)

* 2 to 4 times more dimensional stable than aluminum
to 10 times better in damping coefficient for stability and jitter
reduction depending upon the driving resonant frequencies.

* About 30 percent lower in coefficient of thermal expansion (CTE) for
matching of mating parts.

Advantages over Beryllium

*About 3 times greater ductility than hot pressed beryllium with
greater damage tolerance

*Castable for complex and precise net shape configurations

*Weldable for defect repair
*Reduced scrap generation, machining and environmental process
concerns. Does not require post-machined chemical milling

*About 1/4 the raw material input cost [of what?]


Sounds like the solution to the need for a better/lighter A356 alum.
Tomorrow I might be able to get a cost and availability on this stuff.

Ed Carver


Sounds like aluminum/beryllium alloy to me. What is the cost?

Paul Lamar


Just a thought.  I've spent 30 years as an RCP and the worst set of
non-smoking lungs I've ever seen came from an aerospace worker who was
working with beryllium in the 1950's, inhaled the dust and ended up with
a type of degenerative lung disease which eventually killed him.  The
toxicity  of this stuff is one of the reasons that it didn't become the
wonder metal we were all expecting.  If you're doing any  kind of
machining on this stuff you need the right equipment and safety
procedures.  In the 80's we had a patient that worked for Aerojet,
female, about  28 years old who came down with what seemed to be a
mysterious lung condition.  It took us over a year to get the powers
that be to tell us what kind of materials she was exposed to, and it
turned out she was in charge of manufacturing solar panels for spy
satellites.  All sorts of interesting metallic salts go into the alloys
on those things and she ended up with 70 year old  lungs.  A lot of us
used to haunt the disposal yards at the aerospace companies here in S.
California.  Good stuff and cheap, but some of it was dangerous if you
didn't know what you were doing.  Finished parts were usually ok.

George W

There are precautions that can be taken.
NC machine tools were unknown in those days.

Paul Lamar


The material producers are out for the holidays, can't get pricing or
availability.

The apparent sole producer of beralcast is presently IBC Advanced Alloys
Corp., who recently wholly purchased beralcast corp in Feb 2010,  who
purchased starmet corp back in 1999 or so, which originally was Nuclear
Materials corp. from back in the 50s.


Everything I have read so far concerning hazards in machining Be are
for the low alloy pure stuff. The Be in beralcast is supposedly
trapped in the matrix of the other alloys, mostly Al. There does not
appear to be any major concern with toxicity when machining
beralcast. There is relatively high hazard when machining pure
beryllium, especially from a large billet, or when being ground from
a powder metal compression formed part.


There are two major changes in machining hazards with beralcast compared
to low alloy Be. The first is the machine ability is much easier,
machining is similar to common Al alloys. The second is, and this is the
really big one. The stuff can be cast so close to the final shape that
about all you need do, is shave a few thou off the critical surfaces.
Finishing a few prototype rotors on an nc mill is'nt going to be very
hazardous, especially with copious amounts of coolant flowing over the
part during machining.

The stuff melts at about 1200f, and like all metals, is most dangerous
when in a liquid or vapor state.

If the melting point is nearly the same as alum, this should be a fairly
easy part to cast.
It's all sky pie for the moment, until we find out if it is cost
effectively available.

Ed Carver



-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.