Subject: best casting material for center and end housings
From: Rotary Engine
Date: 12/26/2010, 7:48 PM
To: AAA Put this in the To box

Dale,  I wouldn't classify housings that cose $2650.00 apiece for end
  housings as cost effective. As a basis for a four rotor I am not
  comfortable with the series cooling at continuous 6400 RPM. Using
390 or  398 alloy housings no coatings for wear are needed. This
material (390)  is used in lawn mower engines and despite the post
last week that it  wasn't successful in the chevrolet vega it was.
The problems with the  vega were a result of cost cutting on the
part of GM where they used a  much too small radiator and other
cooling system problems. With no  maintenance of coolant level there
were overheating issues. During  overhaul after overheating it took
a 3 step process to restore the  cylinder bores that was ignored by
amatuer mechanics in favor of the  methods they used for cast iron
blocks. Imformation on the vega  durability and cooling problems are
easy to access in yahoo or google.

To produce a two piece end housing with coolant flow paths
  (parallel cooling) as well as increased flow rates and including
  mounting provisions is not that difficult. The housings can be
faced off  in a large lathe and lapped. The lathe approach allows
boring the  stationary gear bore and some "O" ring seats while it is
chucked up for  accuracy. "O" ring paths for rotor housing seals can
be done in a CNC  router. If I didn't have the machine tools I could
farm out everything  with an end cost of $700 for the front or
center housing and $850 for  the bellhousing end. I drew mine up
with a front and rear bellhousing  which are dowel alligned so that
two sets of RX8 internals can be used  for a 4 rotor. As a six rotor
the prop end e-shaft would need  modifications. If I farm out the
foundary casting at $140 and buy the  "O" rings for $90 which
includes double sealing the water to oil seals  at the stationary
gear I can build them for $250 apiece. That would be  about $1500
for all the housings of a four rotor.

  george grimes

Yea, the retail prices on aftermarket alum housings forces me into
the foundry yard. It really is much cheaper that way. I am too
skilled to pay $6k for something I can produce on my own.

The 390 alum used in the 928/944/968 porsche engines worked great as
a cylinder surface, even great for the 944 turbo. The correct
boring/honing process  had to be followed. This is totally different
from the air cooled 911 mahle cylinders.

I'm definitely in the game for producing these light weight parts.

Ed Carver


Hi guys,

I was looking at some speculation on the possible internal measurements of the
16X engine and why Mazda may be doing things the way it appears they may be
looking at. The increased radius (R) and offset (e) are easy to understand.
Like stroking a boing boing engine. The reduced rotor depth or width and the
explanation of flame travel sounds reasonable; more burned fuel for better
economy and less emissions. The proposed dimensions for the 16X are similar to
the 13A engine. Now I know parts for that really rare engine will not be
readily available or inexpensive.

My thought is that if people on this news letter are going to the expense in
time and money to build parts dedicated to aircraft use, maybe it would be an
opportunity to make use of some of the possible design benefits that Mazda and
others have spent millions on. If the R and e of the 13A were incorporated
with the 70mm width of the 12A, the apex seals would be readily available. End
housings would not be very different. Building rotor housngs would pose a
bigger difficulty. The inner oil seals could pose a small  difficulty with
respect to the diameter around the rotor diameter for the greater
eccentricity. The other problem would be side seals as the greater length
between apex seals would require custom build. Corner seals could be used from
what is todays most durable design.

It would not take Jeff a lot to scale the Al rotors to get them to the
required size and also to make the e-shafts.

Maybe I am leaving yellow snow, but just thinking, and maybe get you people
thinking also. It could help bsfc and the larger displacement looks like 305
to 310 HP for a 2 rotor based on the pport numbers. A 3 rotor could be in the
450 to 475 HP range. This with the same weights as current engines.

Dale Davies


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.