Subject: rotor housing steel liner
From: Rotary Engine
Date: 12/29/2010, 7:14 PM
To: AAA Put this in the To box


Hi Ed,

   My thoughts on making the rotor housing steel liner for a 13A/16X
   size radius
   would be to try to get a 13A engine. Doug, would you have any
leads   on one in   Japan? With that we would have the shape of the
inside. Casting a   steel shape   that is the inside dimension would
help form the proper shape. We   would need a   die for the outside
so it forms correctly. Figuring the inside   circumference   would
enable machining a 4130 pipe ID to that dimension. Then   machine
the   grooves in the OD with a tapered burr so the cast Al forms
into it   and can not   come "unglued" or separated. Then forming it
with the dies to the   shape. The   Al could then be cast around it
and the width machined. The area for   the Pport   could be left
without cooling to eliminate sealing there, and the   port almost
 ready to go.

   Anybody alse have an idea on this. Paul, what is the thickness of
   the Mazda
   steel liner?

   Dale Davies

   It is very thin. On the order of .065. Here is how Mazda does it.
   You would be reinventing the wheel :)

   Paul Lamar

  Dale Davies, I don't think you need a housing to measure. There is
in  the Kenji Yamagughi (sp) papers found on the rotaryeng.net
 <http://rotaryeng.net site the formula for generating the shape of the
  trycoid housing. It is generated by  the path of the 3 rotor tips
as  they revolve while the eccentric shaft rotates. You can generate
 cartesian or polar coordinates to as many decimal places as you desire.
  I think my desktop does to 27 decimal places but I have it set to 5
  since that is ten times as accurate as CNC can machine and more
just  increases the file size. A CMM (coordinate measuring machine)
 is not  this accurate.

  If you change either the eccentricity or radius you will be
  makeing a new trichoid shape that hasnt been produced and therefore
  there aren't any parts to measure. The Lada and Chinese rotaries both
  use the Mazda dimensions. Curtis Wright has a vast number of
  displacements for use as both engines and pumps.Some are six feet tall
  inside the rotor housing. They all seem to have the  same ratio of
  eccentricity to radius. If you increase eccentricity relative to
the  radius you improve torque, however I suspect it will not have
as high an  RPM as the current optimized dimensions. Changing the
ratio also changes  compression ratio which will require building a
matching rotor with the  correct combustion chamber depression. The
volume of the depression for  a given compression can be derrived
from formulas posted on this site  last year. If you leave the ratio
the same and go larger then the  currently designed end housing
databases can be 3D scaled up in the X  and Y dimensions with the
same Z  saving some design work. Several of us  have end housing
databases including Jeff and myself.

    The problem with building rotor housings is the final finishing
  steps. They need machined and lapped to .0001 accuracy. This is
  currently done on specialty equipment and not likely possible
  with normally available  CNC machine tools.

    Although scratch building a rotary engine is a huge task, by the
  time you are able to fit lubrication and cooling oil flows  and coolant
  glycol through the mechanical and structural elements of the
engine you  will be better able to modify the available parts to
suit your needs.

  george grimes

Hi

We tried this at Norton circa 1976, we squashed a tube down to an
oval shape, machined the Alum housing to match the Oval. then Kopp
ground the Housing shape, but even then we could not transfer the
heat away from the chamber, and the Air cooled engine would not pass
a hot stop test, even with the best oils of the day, if we carried
out an emergency stop from a sustained WOT  and switched off and
left the motor to cool down, invariably the seals would stick and
blow pass would start, and this eventually caused the Rotor side
face to smear.

I agree with a lot of the comments, however would also point out
that the Seal nose Radius needs to be and was matched within the
geometry, on the Norton we changed from R=70, e=11.6, a=0.5 to R=69,
e=11.6, a=2.5 and this helped the chatter and apex seal spring wear
rate. with the original geometry lubrication the seal would wear in
quite readily to match the geometry, but it could never match
exactly, this caused a radial apex seal movement of around 0.007 "
can't remember exactly and seal would work this cycle four times per
seal rotation, when we went to Water cooled engines the seal spring
failure overtook the after bake problem.

With regards to Mazda, if it is not broken then do not try to fix it,
 I visited the plant for a week in 1988 and admired the Engineering
immensely, I was allowed full access to the development facilities
and we had at least 3 engineering meetings within the week in which
we talked openly about our problems, both direction, I would not
elaborate on Mazda issues of the day even to this day as we made a
Gentleman's agreement not to digress.

Bob Rowley
Ex Chief Test rider for Norton Motors Ltd
over 1 million miles testing Wankel engines from 1968 (BSA) to 1993

Very impressive Bob. I toured the engine plant but not
the engineering labs.

Paul Lamar


Hi Bob,

Great information. All is appreciated. I am not thinking of fixing a Mazda
that is not broken. My thoughts are that if people are building parts for
their own use, make use of some of the new technology. Copy a 13A engine as it
seems to have similar size to the 16X that is not available yet. The 16X
appears to have a rotor width that is the same as the 12A engines. It should
be fairly easy to make the rotor housings 70mm wide. Shape the steel liner and
cast the Al around it. The 13A's were 60mm wide, the same as the 10A.

The more people are thinking and chip in, the better probability something
good is done.

If you guys were to have a clean sheet for design, what would you like to see?
Low cost, light weight, reliability, simple are a few things. What else the
conventional AC have that could be incorporated?

Dale Davies


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.