Subject: 555 verses the computer approach.
From: Rotary Engine
Date: 1/1/2011, 5:57 PM
To: AAA Put this in the To box


 Go here:
 http://www.rotaryaviation.com/eficont.html

 Scroll down until you see these words:

 "Planning to use the EC3?  We get a lot of requests about the number
 of wires needed for the EC3 and other installation details. If you'd
 like to get a better idea of how to prepare for and install the EC3,
 please CLICK HERE"

 Click on "CLICK HERE"

 and download "EC2AinstallRev2.pdf"

 Read the pdf. There will be a quiz later.
 Those passing the quiz will get a honorary degree in computer
 science from the ACRE :)

 Paul Lamar



OK, time for another sophomoric question injected into this
otherwise erudite discussion (sorry....)  What are the most
popular mixture management/ignition systems used in
rotaries?  And how well do they work?  I am getting a little
nervous reading about "flooding" issues, "difficult to tune"
complaints, about Tracy's system.  Any comments?  Thanks.

Gene Kahn

It is hard to say. Mazda buys them from different companies.
Perhaps Mitsubishi. In rotaries flying it's Tracy Crook's
computer hands down. Any time one starts to deal with problems
some people get the false impression everybody is affected that
is using that device. Many people have tuned Tracy's product
and use it with no problems. My feeling is it could be
made easier to tune and cheaper.

The flooding issue came up the day Mazda introduced the
side exhaust port RX8 rotary engine. I bought one of the very
first sold in LA. My brand new RX8 engine flooded in my drive way
within a week and would not start. I have been working on
race cars since I was twelve and the RX8 was the sixth
rotary engine powered car I have owned starting in 1973.
Nothing I knew how to do could get it started. The dealer sent a
tow truck and picked it up. It took them a week to get it started.

Turns out the RX8 engine is so good at preventing raw fuel
from going out the exhaust that it was easily flooded.
People and Mazda now deal with it by cutting off the fuel
pump as soon as it does not start on the first few turns.
Generally it does not occur if the engine is warm.

Mazda changed the computer program and I have learned
not to start it up and turn it off without letting
it warm up first. That was 2004 and I have not had
the problem since.

In an airplane it can be fixed by inserting a small tube
in the lower spark plug hole and sucking out the raw
fuel accumulated in the bottom of the rotor housing with
a turkey baster. I suggested to Mazda at the time to drill
a small hole in the bottom of the rotor housing with
a petcock to let the excess fuel drain out on to the
ground :)


Paul Lamar


There is an option between the 555 and the microprocessor.  I really
liked the 555 idea, but as discussed here months ago, the 555 response
is not linear. I first began with efforts to linearize it - constant
current sources, etc. Eventually I came upon the idea of digital
counters as timers.

I have a breadboard running of an injector control using an 8-bit A/D
converter and an 8-bit  presettable down-counter in place of the 555. A
variable clock frequency allows setting any mixture you want  I dressed
it up a little bit with a crystal oscillator, 4040 prescaler, and
another presettable down-counter with A/D convert interface to a
potentiometer for mixture control.
I have to flowtest the injector to determine the maximum and minimum
clock frequency.


I am using a buffer amplifier on the MAP sensor output which is capable
of two modes, average or peak. It seems to me that if the VE of the
input system is greater than100%, the peak MAP must exceed ambient
pressure by the same ratio, and using peak sensing with a pickup at the
intake port would compensate for a variable VE.
A p-port at sea level with 120% VE would need (instantaneous) 36inches
MAP in order to pack that much air into the chamber. The MPX4115AP would
saturate at 32 inches.

 I am working presently on getting the schematic into ExpressSCH so I
can lay out and order boards.
I plan to fly it this spring on my Subaru-powered RV-6

On another note, Paul, I apologize for the false alarm on the LS coils.
I was testing with one that came off my 04 Tahoe. After your post, I
went out and bought a new one and it will go over a second before it
discharges.

Victor Roberts

No problem Victor on the false alarm. I usually test most ideas at least
on the bench. Makes sense to put some smarts in the GM coils unlike the early
dumb RX8 coils.

Try the CMOS version of the 555. It is extremely linear compared
to the old bipolar 555. When I discovered that  I was ecstatically
happy :) It also has a wider dynamic range. I could hardly believe it.

It is the mass airflow sensor that is nonlinear and the main problem.
The Free Scale pressure sensors are very linear.

Send some schematics of what you are up to. Sounds very very interesting.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.