See the bottom
Are you a pattern maker Ed? If so I might have some work for you.
Most pattern makers using traditionally materials charge a lot
of money for their art. It is a dieing breed as most new
casting patterns are made in NC machines. Core boxes are
particularly difficult to make as the wall thickness is very
difficult to control. I know. I have been there and done that.
Rhino 3D helped greatly but the biggest help was the
stereo lithography machine at Ventura College :) No longer
in operation unfortunately.
Paul Lamar
Before this particular thread took off, I was under the impression that
we, the average engine builder could not easily have reproduced at any
local chrome shop, the thin lining on the steel liner. And, that if nasa
could not successfully apply a coating of silicon carbide on the alum
surface they created, then probably we could not do it either.
nasa obviously chose a poor apex seal for testing. Shame on them, they
should have known. Taxes down the tek toilet again.
For us, striking out into this difficult issue of developing confidence
in a chosen liner, we otta stick with what we know works for the long
haul.
Bob Rowley, we would love to see how you determined proper ram air
system on your bikes. This could be taken a long way on aircraft. Also,
I cannot picture what you are referring to in your 'dragging cool air
into the exhaust with the exhaust ejectors'. Thank you!
Anyone know of a shop that has successfully applied/reapplied chrome on
a Mazda rotor housing? and made it so that it will last?
Paul, I don't mind sounding naive, (happens regularly), the production
of an intake manifold is something I have considered many times. I
watched a youtube about a prototype shop building a V8 manifold down in
Oz. Did'nt appear so tough to do, just gotta have the correct casting
sand with binders, and an oven.
Could I do it? I'm not a mold maker. I don't see why I could'nt.
Anyone out there have, or know someone who has, an induction furnace
with a crucible that will handle about 20lbs? It's really amazing how
inexpensive and small, these hi freq furnaces have become. Cheaper than
my syncrowave.
Ed Carver, ex moto pilot
Check my book How to Cool Your Wankel on the exhaust ejectors
Ed. AKA Augmenters. Page 63.
Paul Lamar
Bob Rowley, we would love to see how you determined proper ram air
system on your bikes. This could be taken a long way on aircraft. Also,
I cannot picture what you are referring to in your 'dragging cool air
into the exhaust with the exhaust ejectors'. Thank you!
Ed Carver, ex moto pilot
Check my book How to Cool Your Wankel on the exhaust ejectors
Ed. AKA Augmenters. Page 63.
Paul Lamar
Hi,
We carried out some development work for and with Teledyne Continental
Motors, the Ideas was used I believe in the 1930 by TCM? so not a new one,
we had around 84 BHP when the (hot) air intake was sucked through the engine
internals, when we allowed intercooling / cool air through we the ejector
sucked the air through the engine only, got about 110 BHP, port changes by
Brian raised the levels of power almost on a daily basis, our trick if it
was a trick known or otherwise was to pressurize the complete system fuel
tank, carbs and the like, so clearly we could not allow plenum pressure to
be out of balance, the BHP went up to around 125 on the test bed and the ram
air perhaps gain another 10 BHP, the actual result can be seen on Youtube
see link, the smoke that the Commentator mention's is in fact fuel vapour
due to high pressure flooding the float bowls under braking, we reduced
this greatly by installing a BI-Pass valve " called system X" when the front
brake was applied a switch diverted the fuel back to the fuel tank.
Some of the prototypes caught fire due to flooding, and a trick that I was
taught by an old BSA tester worked every time and that was to switch the
fuel off and rev the engine and suck the flames back in, Trevor Nation had a
belly pan fire whilst we waited for the flag to start the race, ( seemed
like minutes but in reality was just a few seconds ) I convinced and eagle
eyed Race Official, that the flames would go out, I was relieved when
looking up the track after the start to see TN in 3 rd place and black smoke
come out of the belly pan and then stop, they got the black flag ready but
it was not needed, TN qualified for the main race and he went on to win, the
race that he subsequently won is on Youtube and he broke the lap record, the
circuit being Caldwell Park, near Lincolnshire.
Link
http://www.youtube.com/watch?v=kBg86bjr8l0
Snetterton was an old WW2 airbase with a very long straight that allowed us
to reduce the handling penalty, allowing us to pass down the straights.
I rode the first prototype converted road bike at M.I.R.A near Hinckley "
another ex WW2 bomber base " in 1983 and lapped for 1000 miles at WOT at an
average speed, including stops for tyres and fuel with a lap speed of around
128 MPH, and much later 1987 rode the official Prototype Racer (Waltzing
Walter ) and averaged 155 mph on the same track, Brian Crighton, was the
Engineer responsible for tuning and developing the bike.
http://www.realclassic.co.uk/wankel06082500.html
Bob Rowley
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.