Subject: 2 to 4 rotor question
From: Rotary Engine
Date: 1/5/2011, 8:27 PM
To: AAA Put this in the To box


 From past experience of piston cranks, I know they can be welded and
repaired. Now, the question, could I cut, weld, and heat treat two 13B
cranks to make a four rotor?

Regards,
Norm P.

Well yes and no. Most 4 rotor e-shafts are three pieces.
Other wise you can not get the engine together.
You almost have to have taken apart and put back
together a 2 rotor to understand why.

Paul Lamar



Norm P. There is a lot you can do for drag racing that will not survive
in airraft use.  The first problem is that a normally aspirated P-Port
four rotor is 500 HP  at  takeoff RPM and 440 continuous available for
cruise. With more gear reduction than 2.85 to 1 the horsepower can be
well over 600.  Using the stock components lined up on a custom
eccentric shaft the cooling  glycol goes from the pump through all the
side housings and rotor housings, then crosses across the rear housing
and back to the front housing outlet . As the water heats up progressing
through the assorted housings the cooling around the spark plug area
becomes inadequate resulting in detonation. The plugs, apex seals and
stationarg gears will have problems from the detonation. There have been
conversions of intermediate housings to allow parallel cooling where the
coolant only passes through a single rotor housing. This is possible but
the tension bolts and water seal "O" rings limit the size of opening
into the housings.

 Second concern is balancing the e-shaft.  Many people have
built four or more rotor engines with the eccentrics staggered 180
degrees to balance the  rotating assembly with counterweights only on
the ends of the shaft. Theu use stock counterweights which are also used
as mounting flanges and spacers for other parts. If the two intermediate
eccentrics don't need counterweights then using that same logic the end
counterweights on a two rotor which is an 180 degree offset wouldn't
have counterweights either.

 The accessory  pumps are also a problem. An oil pump designed
for a three rotor  would be a stretch on a high output four rotor, If
all the oil was for lubrication of eccentric and stationary gear
bearings that would be fine. However 1/3 of the heat rejection of the
engine is from oil sprayed into the rotors and around the E-shaft. As
continuous power increases so does this need for heat rejection. The
three rotor water pump is also low on flow rate for a four rotor which
needs 50 GPM at full power. The pump has twice as many passages to push
the water through and therefore more back pressure which will reduce the
flow rateeven further.


There are several ways to address these issues. You can search
the Internet for the five rotor Curtis Wright aircraft engine which
might give some insight.  Also on the Internet is Grannies speed shop
which close coupled two complete  two rotor engines less one flywheel
and starter. This was raced in a circle track modofied. The stock
E-shafts were connected with a home made coupling. After you get
through Paul Lamars web site you should also go thru
Craigsrotarypage.com which has a lot of info particularly on the foreign
engines such as the Russian 3 and 4 rotors aircraft engines.

 The basic Mazda parts are accurately described as robust as
evidenced by huge two stage turbochargers and NOS systems on drag racing
cars making 1600 HP. The cooling and lubrication issues of an engine
under load for seven seconds  is different than hours at near wide open
throttle in an aircraft.

Personally I went with stacking complete engine rotating
assemblies with aluminum end housings, The rear or the front engine and
front of the rear engine have matching bell housings located on dowel
pins for alignment. The center housings are modified for parallel
cooling and extra fasteners are added. The oil system is a 5  stage
stock car gerotor type and the water pump is 426 Chrysler big block. The
designs are frozen, the G-code is compiled for my CNC gantry router but
I haven't built a test engine yet. I plan on putting a six rotor in a
1965 E-type Jag with turbocharging.

George grimes

AA Drag racing engine frequently don't have any cooling what so ever.
The metal does not get a chance to over heat in 5 seconds.

One way to cool a four rotor is make all end an intermediate housing
two pieces NC furnace brazed together with parallel radial cooling by
external plumbing. The secret to making this work is monitoring
the rotor housing with four thermocouples mounted just below the lower
spark plugs sending info to four temp gages on the instrument panel.
Then tailoring the flow accordingly. Not a bad idea for a 3 rotor
as well.

Endurance racing Chev V8'a are frequently modified with parallel
cooling system using a plethora of external plumbing hoses.

The Orenda big block based Chev V8 $100,000 aircraft engine had
external parallel cooling galleries cast into a custom block design.


Paul Lamar


Paul,  I am running the water in the center housings just below the
lower spark plug  to an internal manifold.  From there it divides and
feeds half through the front rotor housing and half through the back. The end
housing  internal flow manifold distributes the return to the center
housing and is used to heat the cool side to reduce temperature
variations in the housings side to side. The water exits the top on the
intermediate housing to carry steam away.There is an obvious difference
in flow passage capacity in the stock housings shown in your
attachments.

There is about three  times as much area on the hot side as
the cold side. As seen in the attachment only two thruholes go directly
into a rotor housing opening while 9 line up with the hot side passages,
On the face side which is against the rotor housing there are recesses
cast in the stock rotor  housing which allow flow around the intake port
area to additional rotor housing coolant passages. I have expanded on
the recesses and added more area thru the housing to increase flow back
through the cool side of the housing. This will not change the actual flow
through the rotor housing but will allow future increases.  Several of the
cooling passages thru the stock rotor housings have bulkheads with
smaller thru passages to control flow rates and add turbulence. In
future I may drill out a percentage of blocked areas until the area is
equal in both directions. At that point additional end housing flow may
be useful.


I am using a balanced piston flow divider on the exit side
of the water flow where the two engine modules water combines to go to
the radiator. Any difference in flow pushes the piston towards the low
pressure side to increase area on the higher pressure side until the
flow is close to equal. There are no thermostats used.


I get the idea of the thermocouples to equalize cooling  which
will be useful on a test stand. Trying to implement something to bias
the balanced piston flow control  is doable if necessary. An adjustable
spring on each side of the balanced piston could be added  and set at
maximum cooling load.

george grimes


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.