Subject: Better and cheaper trigger for the 555 EFI
From: Rotary Engine
Date: 1/5/2011, 9:13 PM
To: AAA Put this in the To box


Roger,

This is cheaper than the ABS sensor and works
better. Klause has been using these for years.

I cut the trigger wheel with a large hole saw :)

Paul Lamar


Paul,

Been studying the hall effect sensor, and it seems to be the best
approach, however, the interface wiring and circuit that will integrate
the Hall Effect into the 555 is a bit unclear, I am clear of how the
Hall Effect sensor works, but reading from the text,  an amplifier is
mentioned, and on the first pic there is a pic of a coin, , hall effect
sensor, and a chip.

That chip, is that the amplifier?

Where do you wire up the coin?.....  :)

Roger

No interface circuit required. Puts out a beautiful negative
going pulse. Just what the 555 wants. See the scope picture.

That chip has no relevance to a 555 circuit. Sorry! It is used with
CD ignition systems and can be triggered directly by the hall
effect sensor. When you get a chip part number like that you
just put the part number in google and it will tell you
all it knows  about it. (a lot) :)
ST is the maker's logo and L6384E is the part number.

All the Hall effect sensor requires is one 10K resister
connected to 5 volts. As in the picture of the prototype
board. The color code of the resistor can also be found
on google. I don't know how I got along with out google. :)


Paul Lamar

Isaksson Roger wrote:
Paul,

Thanks, most of the data gathering is at hand now, ...went and got some
pressure sensors at junkyards today for testing.

Found out one interesting fact, some of the Ford Manifold Absolute
Pressure sensors have an integrated circuit that will convert an analog
signal ( the 1-5 V up/down movement), to pulses, faster and slower, the
pulses, are 5 V.

All they need is just  power feed, and different pressures and they will
pulse in different time intervals.

For a sequential system this is irrelevant and I just can't use that
type, but for a batch fired system this has some very interesting
consequenses.

The idea to fire the injectors with a pulse, from a spinning magnet,
that in turn has to be picked up , and sent back to the 555 chip that
will give it a trigger pulse............ can then be bypassed.

The MAP sensor itself will give longer or shorter pulses depending on
the vaccum...hmmm.

Check it out, really interesting, the 555 system can be simplified one
more step.

That would mean that there is a high possibility that a MAP sensor,  can
directly drive the 555 chip, skipping the rotating pu coil, Hall effect
sensor, ABS sensor or whatever is choosen to produce pulses.

It's changing pulse in direct correlation to vaccum, so everything is
already there.

Not all Ford MAPS are giving a digital pulse signal, so it has to be
researched and selected to find the right ones , but it immediately
opens up another avenue here.

As I say I will go the sequential way, but it might be something for you
to look into for the batch fired system, it would be really neat to have
a system that works with that principal....can you ask for anything more
simple ???

All I really know now is that those sensors will change the signal to
digital, and it is a square signal. I have not done research enough to
tell if the signal is going "the wrong way" so to say, meaning when it
is vaccum, and the trottle is closed, and the engine is idling...the
signal might be fast. We don't want that, but again, have not
investigated this further, and are leaving that venue for you, or
someone else, that are doing a batch fired system.

In case the trigger signals from the Ford MAP sensor will follow the
desired pattern, less vaccum ( full throttle) fast signal pulses, and
vice versa, then this might very well be a winner, as the pulses are
directly correlated to the absolute pressure ( what vaccum the manifold
happens to have at the time) , and thus are more tuned to the fuel need,
rather than to take out the signal from RPM.

Taking out the signal from the RPM will make it more complex, and give
many more false situation that has to be mastered, like as a high RPM
can be had, and you are letting up the throttle. All the RPM counter can
see is a fast spinning wheel, and thus it pulses very quick anticipating
a very high fuel flow, but the pulse width will have to be very low or
almost non existent, because the throttle is up, still the RPM counter
will sit there and rattle away firing commands to the injectors.

A vaccum controlled pulse trigger will instead immediately respond to
the current fuel demand, drop or rise in pulse intensity depending on
true need of fuel.

If the trigger pulses have a very small window, in it's min/max pulse I
don't know that either, so if they are dirctly translated to useable
fuel pulses, in that sense, needs to be looked into.
The pulses are ment to be looked at by a computer, and may not
correlate. Most probably they will be fully useable, and this is why I
think so.

Lets say a Rotary does 1000 to 6000 RPM ( just taking numbers), if a
magnet trigger is used together with a PU unit, that means that the
trigger is increasing in a ratio of 6:1 over the scale, and if the
digital MAP sensor is increasing only in a 2:1 ratio, it wouldnt follow
suit.

However,  as the vaccum itself will determine the ammount of fuel, not
the ammount of pulses per se, the trigger pulses don't necessarily have
to follow the
RPM, they follow RPM only because it is a convenient way to tap pulses
from a rotating magnet that is attached to a rotating mass on the
engine, so therefore we will get a pulse that correlate with the
RPM,..but it doesnt neccesarily have to.

If an engine is running 6000 RPM and a batchfired system will pulse at
an odd number....lets say 4838 RPM , it will run as well, as long as the
pulse length, will ensure that the injectors will stay open to deliver
the appropriate ammount of fuel....I know, we run into another thing,
injector sizing and all that, but the point is that if a digital MAP
sensor is running the trigger, it doesn't necessarily have to correspond
with the RPM, as long as the length of the pulse to the injectors will
do the trick.

The digital MAP sensor would do nothing more than provide a pulse.....so
....if a digital pulsing MAP was to trigger the 555, it would only
replace the spinning magnet and pu coil......it wouldn't do anything
else, ... then another MAP sensor, an analog MAP would decide the 555's
pulse length, then ....voila...we would have it all solid state.

How about that...
... one digital MAP sensor triggers the 555
... one analog MAP determines the pulse length

That would be really elegant.

The FI system could be made into a small box, where one hose from the
intake manifold is connected to the FI system ( Internally there would
be a T to the two MAP sensors sitting on the board,),   there would be
one wire harness to the adjustment screw in the cockpit, and one wire
harness to each injector...one black and one red wire for the power feed,
and that's it.

Then some logos on the box..."Lamars Plastma Eater".

Again, I am leaving this, but thought of tossing the thoughts out there,
as a very interesting way to drive the batch fired 555.

Roger

Wow that is interesting.  See if the pulse width is truly
proportional to MP. They must have a 555 in there. If true
all you need is a FET to switch the injector. Well not quite.

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.