Subject: Aluminum rotors.
From: Rotary Engine
Date: 1/7/2011, 10:51 PM
To: AAA Put this in the To box


  I have a suspicion that an all alloy rotor would have problems
  with keeping the fit of the pressed in e-shaft bearing with the
 rotor
  expansion and contraction due to temperature. I was considering
 using
  what I would call a flanged sleeve made of steel to mount the
 bearing
  and stationary gear. The stationary gear fits into the face of the
  flange, the bearing in the bore, and the alloy rotor fits over the
  outside of the sleeve with dowel pins into the back side of the
  flange.
  It doesn't appear too difficult to CNC the negative patterns to
 cast

  the
  wax as a left and right side with the wax sections keyed together.
  The
  difficult part is machining the side seal grooves which was a major
  stumbling block for rotamax. I was thinking of a router motor
  swinging
  in the proper arc over an indexing table but reading how much
 trouble
  others have had with this it is obviously not that easy. Useing 398
  for
  the rotor doesn't seem to be a problem as far as galling with side
  housings of the same material because the side inner and outer oil
  seals
  keep the parts separated. Temperature control of the rotor might
  require
  a modified control of an increased oil flow thru the rotor from the
  stock Mazda design although a prototype  of the stock type would be
  tried first. Alloy parts with different compression depressions
 would
  reuse the same flanged sleeve.


  george grimes

  There is a steel insert in Jeff's design for the rotor bearing.
  The side seal grooves are a piece of cake for an NC mill.
  Mazda mounts 3 rotors on a pallet and rotates the pallet to cut
  three groves at a time with a broach.

  Paul Lamar Graduate of a course in NC machining :)


  Yes, there needs to be a greatly increased oil spray directly
 on the
  inside of the rotor, accompanied with a powerful vacuum to draw it
  out.
  This should greatly reduce temps. I think a dual oil pump may
 need to
  be used.

  Does anyone think the Beryllium/alum cast rotor idea can't work?

  Ed Carver


  I am presently drilling into the issue of obtaining a small
 quantity of
  the beralcast 310 and the nasa 398. Starmet is the exclusive
 vendor for
  the beralcast, and a salesperson is kicking the ball back and forth
  with
  me. I have contacted one of the nasa employees about a direct
  vendor for
  the 398.

  Normal alloy vendors sort of give me the blank stare when I ask
 them
  about these materials. Never heard of them.

  George, have you found a vendor for the 398?

  Ed Carver

  OK guys some things to think about. First the rotary's problem
 isn't
  too much heat in the combustion chamber. Rather the problem is
 that the
  long and narrow chamber REMOVES too much heat for best
 efficiency. This
  is probably why Mazda hasn't made a aluminum rotor besides the
 cost.
  Second the rotor is a nice casting and the side plates are
 probably a
  better area to remove weight. Of course there isn't anything
 wrong with
  a lighter rotor, but heat transfer through the rotor wouldn't
  be a big
  plus. The last concern is to be sure that the apex seal slots don't
  flex or wear too much. That can result in loss of a seal. The best
  material for the light weight rotor might be ceramic, or one of the
  cermet materials.
  Bill Jepson

  I want to point out to the many new guys that this is unnecessary.
  These guys just like to push the envelope :)

  The stock Mazda engine makes a great aircraft engine as is.

  Paul Lamar



  Ed Carver, I really haven't tried to source 398 yet. I like it
 for the
  mechanical properties and would use it if available. Possibly
 there are
  things available as scrap the way that 390-17 can be found at the
 county
  land fill. My next question is how to find out if the whole briggs
  engine is 390 or just the cylinder block. I can use other alloys
 for the
  back side of the housing where there are no wear surfaces and
 use the
  rest of the scrap there. If it is all the same alloy it would
 be easier
  to just pull off copper and plastic parts then melt the whole
 engine.

  george grimes


 I just spoke to a nasa admin about getting some 398, and was
 told they
 have licensed a foundry in the Chicago area to produce and
 distribute
 this material within 3 to 6 months; apparently to the general
 public,
 for purposes such as ours. I would say this is much slower going
 than I
 could imagine. The 398 alloy has barely seen use since it was
 patented
 nearly 10 years ago.

 Still waiting on beralcast corp to reply about availability of
 product.

 Ed Carver

 Ed, most people on here are looking to save money on aircraft
 engines. One gets the price down by using mass produced products.
 Automotive piston engines are not durable enough for aircraft.

 Light weight rotors are only cost effective if you would like
 to turn the engine at over 11,000 RPM.

 The p-port 2 rotor's excellent power to weight ratio is hardly
 in the
 class of a hunk of lead :)

 The p-port exist because we need an intake  manifold of some sort
 anyway and
 the P-port fits all versions of the Mazda rotary and gives an extra
 50 HP.
 The stock RX8 manifold is too high to fit under a cowl.

 IMHO one should focus on real problems if any. I would say
 high on the priority list is getting some weight out of the PSRU.
 True getting the weight out of a one rotor is also up there.
 Light weight rotors will not help much.

 Probably the last thing a 2 rotor needs for aircraft use is aluminum
 rotors.
 Are you talking one rotor engines. There you might save a little
 weight.


 Paul Lamar

 Ed Carver,  Did yiu get a name or E-maik address of the foundary
 in Chicago,

 george grimes


 No George, the fellow simply stated they had released patent rights
 to a foundry in that area to produce the material. I should call
 them back to get the answer to that question. I intended to chase it
 down again in a few months; but probably better to get the name of
 the shop. Will call again monday. The fellow did seem to be
 forthcoming with willingness to help us get the stuff.

 Paul I can't imagine using a non p port arrangement. RX8 rotors are
 not cheap. You will have to excuse my persistence in wanting to
 lighten everything. I truly loathe this iron stuff. There is just no
 point in it anymore unless there is a real good reason for why the
 parts cannot be made of light alloys. Most of the engines I have
 worked on over the past 20 years have been made from alloys of
 aluminum, or mag.

 It does remain to be seen what the costs will be for the materials.
 I hav'nt gotten a reply from the beralcast/IBC corp yet about
 availability of their beryllium casting alloy. Unless the stuff is
 excessively expensive, I will continue development. So we will see
 how it turns out.

 I have installed hyper alloy pistons in engines, many oems use them.
 The pistons are nearly pressed into the cylinders; only .001in. side
 wall clearance. The stuff does'nt expand much. It is also
 inexpensive to create. Much less than forgings. The preferred
 pistons for racing in most of the porsche atmospheric engines are
 made from one of the hyper alloys, with, or without, a cermet dome
 coating.

 Anyone who thinks it is just a terrible idea to create lightweight
 rotary parts from a design perspective, tell me why it won't/can't
 work. The whole thing just gets hotter. That appears to be the
 biggest hurdle.

 Back to assembling my 993 C4 cab. (including air cooled lawn mower
 engine:)


The point of the iron rotors is they run at 500 F.
Aluminum looses half its strength at 500F. Even 398
is 30% down.

The iron rotors are one
of the things that make the rotary so robust. I pointed that
out in my Kitplanes article. The rotors make up half the surface
area of the combustion chamber and are cooled by oil.
The oil cooling is 1/3rd the total cooling on the engine.
The rotor is always in contact with hot combustion
gases on one of its 3 faces. In a piston engine the individual
pistons are cooled at least 25% of the time on the intake stroke
and are only subjected to hot gases 25% of the time.

I would not fly with an aluminum rotor unless it was extensively
tested in endurance car racing like the Le Mans 24 hour race.
It might work but it is going to be very expensive indeed to
test it. Be/Al is another matter entirely.

Paul Lamar



Here's a link related to IBC/Beralcast:
http://tinyurl.com/38txudc


Ed Carver





-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.