Subject: Aluminum rotors.
From: Rotary Engine
Date: 1/10/2011, 3:39 PM
To: AAA Put this in the To box




 Hi Ed;
 IIRC, there were early RX-8 rotor failures in racing due to
   thinned RX8
 rotor interior ribs.

 The current 13B engine has lots of pluses with the soft cast iron
 rotors.
 I think a lot people would be interested in the 10-20+# weight
   savings
 on the rotors, counterweights, eshaft, flexplate  You might get the
 weight of the core under 100#.
 Lighter rotors might double the rpm and HP limit for racing folks.
 Aluminum rotors sound like a good experiment.  The Al/Be sounds even
 better.  Definitely worth a try.  Few people have tried to
   replace the
 rotor.

 Like some of Paul, Bill and Dale's comments -
 Aluminum rotors have several disadvantages including lower
 strength/stiffness at temperature leading to early seals failures,
 higher CTE increasing the chance of seizing in overheat or
   oil/coolant
 loss scenarios, poor wear resistance without heat
 treating/anodizing/hard anodizing - not sure how that would affect
 things.  I have heard of many blown rotor and complete
   oil/coolant loss
 stories where the engine still made it home.

 David Mathes was investigating AM-SC1 as another iron replacement
 years ago.
 Al-SiC http://www.mc21inc.com/ looks like a cast-able replacement
   with
 properties closer to cast iron.
 Lots of ceramic/cermet out there:  Sialon, Si/N, C/C, C/SiC.  More
 exotics on the horizon.  Mcubed.

 Some of them can be near cast to reduce or eliminate finish
   machining.
 If I were you, I would literally copy an existing rotor to maintain
 compatibility with off the shelf parts.  Lightening the eshaft,
   cw and
 flexplate is easy enough.  gears are cheap and readily available,
 increased oil flow and pressure as well.
 Iron end-housings are another obvious weight savings target.
    Integral
 redrive, delete the 2nd gen CAS, lighter water pump. lightweight
 exhaust, reduced flexplate/ring gear/permanent magnet alternator...

 Cheers
 Cary

 Nebraska Doug, If I can get the stuff, I will definitely try to push
 it through. Is there some reason why you like the 363 over the 310?
 IBC/beralcast may only sell to us if I use them to cast it.


 Cary, there will be considerable design changes whichever light
 alloy we use. The external dimensions will remain the same. The
 internal webbing will not. That will be modified to spread out the
 stresses, and to improve flow of the oil form one side to the other.
 I'll check out the ceramic stuff tomorrow.


   Ed Carver


This is the reply I just received from Beralcast regarding my desire to
purchase some of their product.

""Hello Ed,
**

** *I have reviewed your requirements with our engineering staff here at
Beralcast Corporation and, unfortunately, we have determined that your
application of interest is not compatible with the strategic direction
of the company at this time. However, we very much appreciate your
interest in our capabilities and look forward to the possibility of
working with you in the future on other programs that may require
lightweight/high stiffness metal matrix composities.*

***Best regards,*

* David Hinds Manager, Aerospace & Defense Sales Beralcast Corporation
55 Jonspin Road** Wilmington, MA 01887""*

Looks like a copy and paste reply.

I'm going to try one of the other salesman, somehow I was directed to
the aerospace division.

OTOH, I'm small potatoes, and have no experience dealing with shops that
customarily deal with complex contracts. Anyone have a better approach?

Ed Carver

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.