Subject: Lightweight center and end housings
From: Rotary Engine
Date: 1/11/2011, 6:54 AM
To: AAA Put this in the To box




    There was a post by (George?) or someone else, intimating that
    they were going
    to make some light weight center and end housings for much less
    than half the
    cost of Racing Beat product. These would be P-Port only.
    I have a serious interest for these, and as we are pretty much
    all building
    P-Ports, there should be a significant and immediate demand.
    Probably more so
    than a light weight rotor, as there are fewer technical issues
    to prove out.
    If there is a real effort to move forward with these, I would
    like to throw
    support that effort in any way I can.
    C. Smith

    I agree. That is a very worth while thing to do.

    Paul Lamar


    C Smith,  I have something like 18 different parts designed. By
    selecting three housings and the corresponding wear plates a 2 rotor
    or three rotor module is assembled. Substituting the front
    bellhousing option for the rear engine joins two two rotor modules
    for a four or six rotor. Adding to the mix there are side housings
    for P-port and for side port. The wear plate is intended to be
    390-17 aluminum or if available 398 for the higher strength. A front
    or intermediate wear plate can be substituted  with dynafocal
    mounts. There is one for the P-port and one for the 8 port (side
    port) versions. All the parts are interchangable except when the low
    mount chrysler water pump front housing is used. This part is not
    compatable with the dynafocal mounts. The stock appearing front
    housing can use a Mazda water pump. I will try to attach a few JPEG
    images. Notably the joint between the wear plate and it's side
    housing have tripple "O" ring sealing. I will send a second post
    with a few more screenshots.
              george.grimes


   Back again, I have solids in .3dm and can do .stl or .step versions
   of both the patterns (with machining allowances) and the finished parts
   with "O" ring tracks and groves. The finished machined files could also
   be used to do CNC versions of the parts.  As a CNC version You would
   probably need to do the wear plates in iron for nitriding. The two piece
   housings are all meant to be bolted together with the included "O" ring
   provisions for sealing. It might also be possible to bond the parts
   together with adhesive but the "O" rings seem more reliable to me.
   Notice the side ports have all the kinks sorted out. The ports are
   mostly CNC machinable with the two plates separated except for a 1/4"
   thick bulkhead across the wear plate which is not reachable with a 3
   axis mill. This would be left as cast for a P-port to seal off the side
   housing.  There are also fuel injection mounts for Bosch injectors which
   point straight thru the port into the rotor housing.  If you care to CNC
   out a set of test housings I can send you the files. Just let me know
   which water pump and mount you want and the number of rotors. (maximum
   is six rotors) I also have the pattern files sliced into individual
   files for making a stacked up pattern from MDF to cast permanent
   patterns. I could send you the whole lot of it on two DVD with support
   drawings of fastener locations. There are additional 5/8" tie rods
   added. The wide housing for the three rotor was in progress when I
   stopped to put up the hanger and install machine tools. I don;t know if
   the ports are the final version and I decided it needed a counterweight
   and hadn't designed that yet.  These parts were all designed to be cast,
   then bored and faced off in my lathe which swings 26" The "O" ring
   tracks require CNC where the two parts join.

   george grimes



   George, I can easily see you have the housings sorted for the most
   part. It would be nice to have a 50kw induction furnace to melt the
   stuff and pour it. Those things are'nt terribly expensive. I have
   some 390 alum engine blocks we could use to start the project. The
   398 is going to be off a ways, but for housings, the 390 looks
   better than the 356 anyway.


For wear plate, how about finding a steel that has the same expansion
characteristics as aluminum. I believe it's available. Could be used to
cover the whole housing surface. Bond it to the alum, and go lap it.

Ed Carver


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.