I had a conversation with a pilot on the alcohol auto fuel
problem in composite airplanes. He tells me you cannot
get gasoline in Texas without alcohol in the fuel.
Is that true?
Back when I was living up in Northern Ontario our fuel
lines used to freeze because of a small amount of water
in the fuel. We carried Alcohol to dump a small quantity
in the tank and it would immediately find the frozen water
and melt it so to speak. By the time you could get back in
the car the engine would start again.
Water goes to the bottom of the tank. What would happen
if you put water in car gas with alcohol in it and then drained
the water from the bottom of the tank? Would the alcohol come
out as well?
What affect does alcohol have on rubber bladder fuel
tanks?
Paul Lamar
Yes, Paul. You would be hard pressed to get gas in Texas without
Ethanol, unless it is from a Mexican restaurant ;-). Gov Perry
apparently got lobbied and had this put in place.
IIRC, the current issue of Aviation Consumer (perhaps your issue of
Kitplanes...not sure, but I read it in the last several days) list a
couple of web sites that provide info on getting non Ethanol fuel. I
was meaning to go look at it but have not yet done so...I was quite
curious is there was a way to get it somewhat easily in GSOT (Great
State 'o Texas)
Chris Barber
Houston, GSOT
The pilot guys in Oregon are lobbying the gov to get non Ethanol fuel.
What about Louisiana? You Texas rotary guys could buy an old
fuel truck and make runs for what you pay for 100 LL :)
Or just fly over and fill it up :)
Paul Lamar
http://www.pure-gas.org
Ethanol free gas for lawnmowers, boats, etc.
Search by state.
Prices seem to vary widely depending on quantities the location is are
able to sell.
They did get the law changed in Oregon so that the highest octane grade
does not have to have ethanol, but I haven't seen any stations yet where
they are offering that.
Perry
Yes I think it would be huge problem for gasoline power boats
with integral fuel tanks.
Paul Lamar
This is a list of states that have non Ethanol fuel.
AB AK AL AR AZ BC CO FL GA HI IA ID IL IN KS KY LA MB MD MI MN MO MS MT NC ND NE
NH NM NS NV NY OH OK ON OR PA SC SD SK TN TX UT VA VT WA WI WV WY
Looks like Texas and Calforni is a flyover state if you have a composite aircraft :)
What about rubber bladder fuel tanks in Cessna's?
Paul Lamar
-- I believe one of the Texas provisions is that is must have Ethanol in major
cities such as Houston. Sigh.
About 2.5 years ago I had to rebuild the strakes (fuel compartments) of my
Velocity when my original coating of Jeffco failed. I had a persistent leak
that I could not seal with the conventional methods. Finally, after discussing
the matter with the factory, I cut into the top of my fuel tanks. Inside large
sheets of the Jeffco was peeling from the tanks. Even though the left and right
tank were constructed at different times, I had failure in both. Of course I
reviewed my memory of my proper application was verified by my buddy who
assisted with the process. While we MAY have missed something, it does not seem
probable considering our obvious awareness of the gravity of fuel tank construction.
I had to completely cut off the tops of my strakes and re-layup the inner skins,
this time sans Jeffco. The reason I used Jeffco was that is was purported to be
more resistant to unusual fuels and additives. At the time I was minorly
considering the Deltahawk diesel (love my diesel Jetta and its 40 mpg average in
mixed use). The only kinda positive is the Velocity is constructed with EZPoxy
84 which currently seems to be the acknowledged "most" alcohol resistant. I
reconstructed the tanks with the EZ84 and placed several test cards in a can of
gas I got from the Shell station across from the airport. So far, 2.5 years
later, when I last looked several weeks ago all was ok. No slime or apparent
degradation. Anecdotal, yes, but at least it is something.
I sent some of the failed Jeffco to Velocity to have a look but they were at a
loss. They did check their tanks though.
NOW, WE NEVER found a smoking gun as to the cause, however, it was widely
believed by those choosing to comment on my internet postings that Ethanol was
the likely culprit. Much speculation. I did buy new Jeffco, but never used it.
It sits on a shelf in the hangar as another expensive lesson/reminder. Two
steps forward, three steps back....
This is one of the setbacks that only now has me somewhat close to trying to
take this pile of fiberglass and metal and calling it an actual flying airplane.
I seem to have had two of the rear apex seal springs (RA springs, IIRC) go
flat on me and am currently waiting for new Mazda springs to arrive from
Mazdatrix, Replace them, button it up, test, have a squawk party and then start
looking for a DAR.
That being said, I am pretty pleased with my current installation. I have moved
from "proof of concept" to actual flight ready install and I think it looks
really good. This also makes me cracking open the engine more of a process as
opposed to a PITA experience that I dreaded. I have become somewhat
philosophical about it now that I am a bit more familiar with the process that
is just "one more thing" and not as big a deal.
I have run the turbocharged engine on the ground in the middle of a hot, humid
Houston summer (ramp temp around 120) for well over an hour with good cooling.
However, I rev it up and the temps soar. I don't really know how to properly
duplicate flight conditions for cooling on the ground. For now I am taking some
solace that it cools well under the load of my IVO prop.
Chris Barber,
Houston
Send me some pictures of the cooling system and I will see what I can
see. Put "private" in the subject if you are bashful :)
Paul Lamar
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.