Subject: Lightweight center and end housings
From: Rotary Engine
Date: 1/13/2011, 10:11 PM
To: AAA Put this in the To box






      I'm building a 2 rotor, P-Port, I have the standard RX-7 water pump,
      do not need
      dyana-focal, have the Doddridge plate mount.

      C. Smith



   C Smith,       If useing a stock pump I measured from a 2005 RX8 which I
   have 3 of.  I also have an RX7 front housing Bruce Turrentine gave me
   and it looks like using an RX7 front cover and water pump would also be
   usable. The RX8 has as I remember two additional attachment bolts. I
   think I will just send a copy of all the parts in .3Dm rhino format. The
   file names with front in them are the accessory end housing, Files with
   rear as part of the name are the bellhousing end. There are files with
   intermediate or center in the name which are both center housings. There
   are several drawings with all the housings shown on the same sheat. One
   with the surfaces filleted and one without fillets.

   All the "rear"
   housings have a 3" extended flange to mount one of Jeffs motor plates
   without spacers or Tracys mount. There are several bolt locationa added
   not in the car bolt pattern. All hole locations are  on the  "bolt
   locations" drawing. If you don't want the extended flange use the slice
   or wirecut command and remove 3". A list of number and letter drawings
   are individual parts pre sliced to make patterns on a CNC router out of
   3/4 MDF.

   If you are not useing parallel cooling a devider web needs
   inserted in the front and center housing at 12 oclock to convert to
   series cooling 1/2"wide flush with the face of the housing. No charge
   for shipping but here's an idea. Anyone who wants a copy can get 1 from
   you and the next guy from him etc.Consider this as open source. I am
   currently interested in getting something that looks like an airframe
   built while there is room for it in the hanger. I am hoping to get my
   wife to do the rotary engine patterns and trips to the foundary when it
   gets warmer. Plesant garden machine shop will do the machining on their
   lathe and "O" ring tracks on CNC milling equipment. Then I would run a
   two rotor version on a test stand for 200 hours. I don't see this all
   being done in the next year so I would be glad for someone to do the
   test engine for their airframe.

       I didn't manage to take a flight test for a  private licence back
   when I had enough  cross country hours. Now the rental and instruction
   cost may be cost prohibative. I got a 98 on the written and then the
   flight test pilot bent up his plane the day of the test and didn't care
   to go flying any more that day. Then I had two engine failures in rental
   planes in the same month and decided certified aircraft engines were not
   in my future.


   george grimes

   No 3dm's came across George.

   Paul Lamar



Paul,  I sent Chris a DVD with all the parts on it. I will get a list of
the drawing numbers for the 3 housings (six parts) he needs to have CNC
cut to build his 2 rotor. I also sent bolt locations and the development
curves the parts are lofted from and a series of JPEG images to use like
an index to see what the parts look like because the drawing names are
alphanumeric files. I think CNC parts are more expensive than cast parts
but  for only one engine probably the best route. I sent the pattern
files also just in case.

          I just looked up the      racingbeat.com
<http://racingbeat.com>        housings which cost $3700 per set and
they use plasma sprayed wear coatings. I didn't have any luck attaching
the file because it downloads as a folder instead of a page.
        Hopefully C. Smith will locate a supplier of 390 or 398 in
billet form or can have someone cast a billet to CNC the wear side out
of.  The non wear side can be 60xx billet.

        As we all know aluminum is roughly 1/3 the weight of iron and
1/2 the strength. Judging from the weights listed for the racing beat
housings they have upped the material thickness  to provide the
equivalent strength.  I ended up doing that also opting for durability
over maximum weight reduction.If the weight savings turns out to only be
30 pounds that is still a meaningful percent of the core engine weight.
I see the real advantage as being able to incorporate parallel cooling,
aerobatic capability, dry sump, additional rotors, mounting provisions,
material for porting and smoother intake ports while using the entire
rotating assembly of a mass produced engine.


george grimes

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.