This looks very promising for our use.

 The coils can be mounted on a heat sink from the looks
 of them. That looks like a huge advantage to me.
 I'll have to get one to look at it and test it.

 Paul Lamar

 I just talked to MSD and they said the dwell time
 is 4 to 4.5 ms which is an improvement on the 5 ms LS2.
 Also the bottom is flat so it can be mounted on a heat
 sink with two bolts rather than the RX8 coil which only
 has one hold down bolt and would require an additional
 clamp.

 These points seem minor but believe me they
 are important. The LS2 cannot be mounted on a heat
 sink but it has a very small heat sink on it and
 we are attempting to fire it twice as often as it
 as it is designed to do and or see's in a 7500 RPM V8.
 That means it is drawing twice the current and generating
 twice the heat. The V8 cylinder fires every other rev rather
 than every rev as in a one rotor.

 The icing on the cake is these MSD coils have CD built
 in and fire multiple times at low RPM.

 Paul Lamar

 Paul, The MSD coil looks like a nice part but the price at
 performance parts.com <http://parts.com is $92.95 each or $699.95
 for a set of eight and the dwell time is still twice as long as
 the RX8coils.I am not up to speed on the electronic circuitry
 but a recentpost said you had eight RX8 coils on hand for testing
 and then laterthat you were down to two. I was wondering if it
 the test rig which isfailing the coils. Possibly not firing the
 plug under compression isencouraging multiple sparks because the
 spark energy needed is lowerjust firing in air. If the intent is
 for developing multiple sparkignition then testing that should be
 distinguished from standard systemsapplication. I have been under
 the impression that Mazda coils cooled bya blast tube are a
 reliable component and that if one were to fail it isunlikely
 that the remaining three would fail on the same flight. Thecoils
 with an outside air blast tube would be significantly cooler than
  the underhood temperature when installed in the car.

 Have you tested a Ford waste spark coil which has no internal
 electronics since that function is in the driver (EDIS) module.
 It might be interesting to see how it stacks up with the
 secondary forthe secong plug grounded firing only one plug. These
 coils are reportedto work up to 8300 RPM firing once per
 revolution (due to the wastespark). If the coils are usable they
 might be tested with the EDISmodule driving them first with waste
 spark then with the second pluglead grounded.

 george grimes

 If you own a $15,000 LS7 what is another $800 for coils? :)
 I am sure there is a huge retail markup. I notice Ebay has a
 lot of MSD stuff much cheaper.

 The dwell on the RX8 is 2.5 to 3 ms while the MSD is 4 to 4.5.
 Not double.

 Yes there is no question the test rig was failing the RX8 coils.

 They don't like an out in the open spark anywhere around them
 They continually re-trigger and the dwell becomes infinite.
 Then they soon over heat lickity split and fail permanently.


 The waste spark is problematic on the trailing coils
 of a rotary but will work on the leading coils. The 2nd gen
 RX7 engine was waste spark on the leading coils. I have not
 bothered to test the Ford stuff as I must be sure it is
 a long term solution and not based on obsolete parts if
 possible. The coil on plug seems to be the long term
 solution for the future.

 Paul Lamar

 Umm, Paul, would a simple coil check, almost possibly part of a
 preflight be to simply swap the plug leads between leading and trailing
 plugs and run the engine up. Won't a failed coil  then reveal
 itself? I guess it could be an in car test as well:)

 John Evans

 I think Tracy has something like that in his installation schematics.
 I am still doing a heat sink mounting that will make the
 coils more reliable. Silly Mazda mounted the coils on the hot
 engine block with a steel plate. Merely making that plate out of
 SS instead will reduce the heat transfer from block to coils.

 Paul Lamar


I was wondering how MSD managed to get a complete multi spark ignition
system in just the coil.

"The history of the capacitor discharge ignition system can be traced
back to the 1890's when it is believed that Nikola Tesla was the first
to propose such an ignition system. In United States patent #609250
first filed February 17, 1897."

I was fascinated by the new MSD coil that combines a multi-strike
capacitor
discharge system in the same package as the inductance coil.

Where does the 500 volts come from to charge the capacitor?
Normally a very expensive switching power supply is required.
How do you squeeze a large 1 mfd, 500 volt cap into such a small coil
package?

Can anybody figure this out for me?

Paul Lamar


The documentation does not indicate a CD system, only a multi-strike
system.

A transformer works by having on one side (primary) a fixed coil thru
which is passed a varying current create a magnetic field which varies
according to the rate of change of the current. The other side
(secondary) contains a fixed coil residing within the varying magnetic
field created by the primary current, into which is induced a voltage
proportional to the rate of change of the magnetic field. When the
points make and current begins to flow in the primary, a surge is
induced into the secondary. The theoretical infinitely short duration of
the increase of current is stretched by the inductance of the coil,
which inductance is the product of several factors including the ferrous
mass of the transformer core.

An efficient transformer requires more
mass for lower frequencies, and less mass for higher frequencies. By
selecting materials for a high-frequency transformer, the core will
magnetically saturate very quickly, will have a low inductance, and will
therefore allow the input current and therefore the intensity of the
field to rise more quickly. Thus a spark can be produced when current
begins to flow, and again when it ends, for it is the change in the
magnetic flux, whether increasing or decreasing, that induces voltage
into the secondary.


Another way to multi-spark an inductive system is to use a semiconductor
bridge to reverse the current flow in the primary to amplify the
"ringing" which occurs during the spark event. By alternating the
current direction in the primary at the resonant frequency of the coil
(several times per millisecond)  the secondary voltage would increase
dramatically and would spark on each reversal.

Coils designed for multi-spark have a lower ferrous mass and lower
primary resistance. The primary resistance  of these MSD coils appears
to be about one-third that of the D-580. The ferrous mass appears much
less than the 580. I am sure their engineers are much cleverer than I,
and could have used some other method to achieve the multi-spark.  I
strongly suspect it is inductive and not capacitive energy they are
releasing.

Victor

I am counting on you  Victor to  think out of the box.
Hint: supposed we tapped off the secondary winding for the 500 Volts
to charge a capacitor?

Paul Lamar