Subject: power question 20B KSE pump on 3 rotor - two stroke turbos
From: Rotary Engine
Date: 1/14/2011, 5:04 PM
To: AAA Put this in the To box

Paul,
Can you see the 20B P-ported, turbo , and super charged being able
to put
out 400 HP?

Regards,
Norm Parmley

Are you kidding? Do you mean 400 HP PER rotor? :)
Have you read the web site below? :)

http://www.rotaryeng.net/rb3rot1.jpg

I would not supercharge the engine. For every additional
100 HP you get out of the e-shaft the engine must develop
an extra 30 HP for the supercharger. Read BAD BSFC.

A turbo charger is a like a turbo compound engine recovering
waste HP from the exhaust. About 50% of the HP in a gallon
of gas goes out the exhaust in the form of heat.

Paul Lamar


 Paul,

 How many turbo-charged p-port engines do you know about?  My
 experience
 with exhaust systems would make me think twice about doing it due to
 the
 overlap of the intake and exhaust strokes where both ports are open at
 the same time.  Any back pressure can cause the exhaust to be
 redirected
 into the next intake stroke.  Maybe that's why they don't turbo-charge
 2-stroke engines.  This also causes more heat buildup inside the
 engine,
 and in my case resulted in failed o-rings.  While a supercharger is
 less
 efficient, it may be the better choice when boosting a p-port.

 Mark

 I have seen several. There is a picture of one on the front
 page of the web site. I took the picture.

 One could turbo charge a P-port RX8 motor and have no more
 overlap than a turbo charged side intake port 13B.

 What kind of O-rings failed? TES O-rings failed?

 Actual measurements have shown the intake pressure always higher
 than the exhaust pressure so if anything fresh air flows into the
 exhaust.
 Just about all competitive turbo charged drag racing rotary engines
 are now p-ported.

 Pressure is pressure so a supercharged engine will put as much heat
 in as a turbo charger all things being equal like inter coolers.
 Any time one compresses air heat is added.

 The latest trick is use early peripheral exhaust port rotor housings
 with RX8 side exhaust port end and center housings. That makes
 three exhaust ports per rotor.

 The rotary is as close as you can come to a turbo jet engine
 without a turbine :) Unlike a piston engine the intake flow
 never stops.

 Notice there is nothing in a turbo jet engine to prevent the burner
 heated air  from blowing back into the compressor. Why does it work
 anyway?
 The fact of the matter is air has inertia. Once it gets going it
 does not
 like to change direction. Gases are interesting objects or devices
 from a physics point of view. They have mass, viscosity and adheasion.
 Much like molasses only thiner :)

 Paul Lamar




 Paul,
 Yes, TES o-rings failed... twice before I figured out the reason for the
 failures.  EGT would go above 1800F if I tried to go fast (WOT).
 Changed exhaust and temps dropped to around 1640F.

 Mark

 I think you are using a RX8 water pump on a 3 rotor so the water flow in
 theory is 2/3rds of what otherwise would be required. The heat transfer
 from the metal to coolant is a strong function of the water velocity
 so local over heating is occurring.

 This KSE sprint car pump has
 been used for many years. You can download a pdf catalog from here.
 http://www.kse-racing.com/Products.html

 These people sell them. Also they are on ebay new and used.

http://www.speedwaymotors.com/KSE-Water-Pump-Front-Cover-and-Components,1820
.html

 Jim Mederer at Racing Beat used this pump on his 1200 HP 3 rotor.

 You will have to make some sort of bearing block so the pump
 can be belt driven. Mazda speed may also have a heavy duty 3 rotor
 pump as the Rolex 3 rotor RX8 cars are getting more HP than your engine.

 I assume the O ring failure happened near the peripheral exhaust port. I
 would
 grind a few grooves in this area on both side of the port as per the
 pictures.


 Paul Lamar


Paul,
Power is total not per rotor. I do like your idea of down sizing and just
using the 20B.

Regards,
Norm Parmley

I knew that :) I was just kidding.

It is a funny thing about scale. Unless there is something
close by to compare it to people have a lot of trouble
telling the difference. Mercedes cars are good examples.
You can get a small econo Mercedes and pay big bucks.
Unless you place it side by side with a big one it is
hard to tell them apart. Mercedes knows that all too well.


Paul Lamar

Two strokes can be turboed quite well and there are 100s of them in
(600cc-1000cc) snowmobiles as we speak making big (200-400) horsepower.  On
a two stroke the intake tract has a reed valve  and they are used
successfully up to 20+psi of boost.  The reed valve idea on a rotary is
still something I would like to try out but that will have to come at a
later date.  I have a running Rotamax single that I might want to try it on.


Bud

You are going to need to fix that rotor bearing first Bud.
Try silicon nitride roller bearings. Expensive but cheaper
than installing pressure fed plain journal bearings.

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.