Subject: article in Kitplanes Why not the rotary 2
From: Rotary Engine
Date: 1/15/2011, 1:51 PM
To: AAA Put this in the To box


Snips...................

The up and down bobbing triangular center body. it doesn't describe a
true rotation, but changes it's position where the center of mass
will be shifting between two extremes, and as I understand, it is
made of steel, right now. If you take a body like that, every time
two of  the three corners in the triangular center body , are on the
outside, the force increases.

The energy it takes to change that mass back and forth between those
two main positions, got to be huge, ..as Newton says, every time you
change  direction, you pay for it in lost energy.

I don't know how it compare with forces in a piston engine other
than a lose comparison, as in a piston engine, the main mass that is
reciprocating is a steel rod, and an aluminum piston, part of the steel
rod is follwing the crank in a true circle,  the crank itself  is
following a true circle. You spin that up to maybe 3000 RPM, on freeay
speed, while the rotary has a much heavier piece that have a shorter
stroke, but much heavier mass, and perhaps twice the rotation...force
needed at twice the RPM is not linear, ...I don't know the exact
number as the baseline is an estimate, but I don't think that four
times the force is too much out of line.

If a rotary would be connected up to an electric motor, and the force
was measured to rotate it, the lower RPM bands would probably be very
good, , but the force needed to spin it in the upper bands  where the
rotary works best, must be terrible.

I can understand it is a matter of structural integrity, but the weight
on that triangular rotor has to come down, and I don't know what material
that is lighter that can substitute the steel and still don't have
fatigugue problems, as it is a critical component.

Titanium perhaps, or perhaps a steel casing filled with aluminum, either
way, that up and down bobbing piece of steel is stealing a lot of energy
to do that movement.

True rotating parts can conserve and store energy, and even if a piston
engine has a lot of parts to it that moves, actually most of it's
rotating mass are both balanced and in true rotation, the majority of
the moving mass in a rotary is not in true rotation,...therefore in
direct correlation to it's mass and speed, it will steal rotational
energy.... therefore to get a distinct leap of efficiency with the
rotary engine, the mass of that part has to come down drastically.

How to do it and still keep the structural integrity...I don't even want
to think about it.

I bet ya in fifteen years from now we can order from Edelbrock a rotary
replacement that is made of a material we can't pronounce.

Roger

"The up and down bobbing triangular center body."

There is no up and down Roger. A common mistake many make.
The rotor CG orbits around the center of the e-shaft much like
the earth orbits the sun. That is why it is sometimes called
a planetary engine. Have you read the Kitplanes article yet?

Here is a good one to read as well.

http://www.rotaryeng.net/how-wank-works.html

"Actually what is happening is the center or CG of the rotor is
moving in a circle around the center of the output shaft while the
output shaft rotates."

"Since there are no reciprocation parts what so ever it is possible
to completely balance the Wankel engine just like a turbine or
electric motor and unlike any piston engine despite some claims to
the contrary. The rotor is balanced around it own axis. The front
rotor balances the rear rotor as they are 180 degrees apart on the
output shaft. That leaves a small couple which is finally completely
balanced by the counter weights."

Here is a good one to read as well.

http://www.rotaryeng.net/how-wank-works.html

Also go on youtube  and watch many Wankel animations as there are
dozens.

http://www.youtube.com/watch?v=yvri-fUNRyk

The only limitations on the RPM of a rotary are due to centrifugal
load of the rotor weight on the e-shaft rotor bearing.

Paul Lamar



Nothing moves up and down in the rotary or back and forth in a rotary
engine.. The eccentric lobe rotates in a circle, and the rotor spins on
the eccentric lobe. The rotor is timed in such a way so that the apexes
of the rotors describe a trocoidal path.

Got it?

Brian Trubee

The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.