Subject: article in Kitplanes Why not the rotary
From: Rotary Engine
Date: 1/15/2011, 7:49 AM
To: AAA Put this in the To box


dear Paul Lamar,

I am mystified ..... with all the stated advantages, why has the
rotary/Wankel, turbo compound engine not superseded the piston
engine? It would have been ideal for say the Chevy Volt. Better
than so called Atkinson cycle engines .......

I know both Curtiss Wright and GM put lots of research dollars
into   the concept and gave it up. I don't know why.

Do you?

So please sign me up for the newsletter ..... perhaps I will gain
some   insight.

Thanks,
Steve Dorr
Orlando, FL

GM did not have the culture for it. They arrogantly thought they could
do it better while Toyo Kogyo merely perfected something NSU already
had working.

Toyo Kogyo (Mazda) was a young company with out a lot of history
so   they were looking for something to put them on the map. Apparently
the Japanese people value perseverance highly and have that never
give up attitude. I also think the TK management was well founded
in   physics so they better understood the advantages. They also
seem to take   a longer view when it comes to business risk.

CW was never serious about going into production. They wanted to
get a contract from somebody to do it for them. I think they were
manipulating the stock to make money on the side.

Me too. It will take some R&D so car companies won't do it
until somebody does it first.

Pratt and Whitney is working on rotary TC here in socal at the
Rocketdyne subsidiary. Even to the extent of filing
one or more patents. Probably for UAV use.

I gave a presentation on the piston TC subject to a collection
of chief Formula 1 engineers. I offered a 20% improvement
in BSFC while all of the other papers presented talked
about a 2 to 3% improvement. It was well received and
the FIA Representative said they would change the rules to
encourage it soon. Formula 1 teams had been spending up
to 800 million US a year. Much of it on engine development.

The current vice president of the FIA is an old race car wing
customer of mine dating back to the late 1960's.

http://www.rotaryeng.net/Oxford-640-4802.wmv

Paul Lamar

Paul,

The rotary engine have a lot of advantages in it's simplicity,
 but how   does it stack up in efficiency?

How far do we get on a gallon of gas ( assuming the same
displacement)   in comparison with a piston engine?

Will it ever be en engine that can favorable compete in cars ( or
airplanes) that will give us those high numbers in MPG.

I am pretty good with that we will have a very compact powerplant
that   can crank out a lot of good power, but what I am getting at, the
survivability, and the social acceptance of the rotary has to
come from   fuel improvements over the current piston engine, not
necessarily in   power improvements.

I think that it just can't be equal with what is now on the
market, but   actually has to show a distinct edge before they will
start to retool in   Detroit.

Even if the rotary is the better engine, ...three moving parts, (
who   can argue) ...that in itself will not change the course of it.
History   has shown many times that a lesser good system can indeed
be the winner.

110 V system sucks, but it won....BetaMax was a much better
system than   VHS, VHS won ... town center trolleys system was
dismantled in   favour of the piston driven diesel bus.....etc etc...

Unless the rotary can give that edge, I am afraid that it will continue
to be a marginal engine, no matter how good it is per se.

If we swap a piston engine for an equal rotary and are getting 65
instead of 40 MPG...thats most probably the way this engine needs
to go,   pure efficiency .

A development that I don't know if it is fully possible....maybe....the
rotary is not without it's faults.

The buzz word right now is "Alternative", and if a steam engine
can be   made to run on wood and water, that will put it on the "alternative"
category and given it an edge right there.....( even if the efficiency
sucks, but hey....we cheated the Arabs...so in that sense, it IS
an   alternative....thats how the thinking goes when it comes to
alternative)

Stuff like that is what's is looked upon right now, as an oil
based   combustion engine is today connected with a negative.....for
all the   right and wrong reasons.

I think that the rotary engine is looked upon with the eyes that
it is   "just another way to burn decomposed dinosaurs" , and is in the
"negative" category..the category of engines we want to get away from.

For the rotary to move into a positive, , into the "alternative"
category, it has to do a pretty good jump in efficiency.

Next hurdle if it does that, is to overcome the idea that it is
basically a 2 stroke, and about as efficient.

So I think it has quite a way to go , it might or might not
blossom into   something and get a new birth in the future, unless
hydrogen fuel cells,   or other technologies are taking over....who knows.

I do believe though that a lot more research and developments has
to go   into this engine, an edge that the piston engine has been
favoured with   for a hundred years, and it is a matter if the
resources and the   industrys ( especially the automotive) interest
is there, to put a bet   onto this engine, a doubtful proposition at
best, considering how much   know how they are already sitting on,
when it comes to the piston engine.

Lacking those big resources, the development may probably come
from   racing industry, enthusiasts, and other intelligensias, and
as usually,   improvements from that arena, have a tendency to get
in on the   established market that way, via the back door..that I
can see as a   possibility.

How it needs to be improved...that's another story, and a big
scope,   highly time and resource intensive, but as with any other combustion
engine, it's a matter of how thermal efficient one can make it.

As with the piston engine in the Hot Rod field, tinkerers did a
lot of   developments, that developed into a ...first a sub culture,
... then   finally into an established industry...and out of that
industry, today   the improvements are pretty much a bolt on thing,
 straight out of the   box, we all know what Edelbrock and Holley is.

...so with this rotary...we will see what gives.

Roger

Well according to Mazda they have solved the efficiency problem.
They now claim the new rotary is more efficient than the piston
engines they sell. We shall see.

For 50 years they have been building the same geometry.
Equivalent to the bore and stroke ratio. Not only that the displacement
has not increased. Nor has the compression ratio by much.
Compression ratio is a major factor in internal combustion engine
efficiency.

The rotary power has gone up from 110 HP to 280 HP in the Mazda
3rd gen turbo. The max RPM has gone up from about 6000 to 9000
in the RX8 engine.

Both Mazda (16x) and SuperTech in Germany changed the rotary geometry
to allow a higher compression ratio. SuperTech is claiming
diesel category BSFC's of .34 running on heavy fuel.

Low RPM torque has always been a desirable feature in car engines.
The US car manufactures have always known that and that is why
they build high displacement, low RPM, light duty push rod
engines.   Same goes for light aircraft engines although of much higher
duty cycle. The Europeans on the other hand go for lower
displacement,   high RPM engines, with dual over head cams and 4
valves per cylinder   and put the bucks into gear boxes. Due to the
autobahn, with no   speed limits, the duty cycle of European engines
tends to be higher.

Mazda is just now thinking of increasing the displacement from
2.6 L to 3.2 L in the 16x. In the mean time the Europeans have
developed the fast shifting, automatic manual transmissions
without   the low efficiency torque converter common in the US.

The current Formula 1 engines are the epitome of this philosophy
with 19,000 max RPM, small piston engines and fast paddle shifting
transmissions.

Consequently there is a very interesting competition going on.

Paul Lamar

Paul,

Indeed there is interesting things going on, just hope to see the
fruits   of it this lifetime.

The claim from Mazda that the rotary now are as efficient as the piston
engine is encouraging, but as always...we will see.

By running heavy fuel you will boost the efficency, the same as
comparison between gasoline and diesel engine, don't know if they
are   running compression ignition though, like the dieselcycle on
that engine   you described, usually it is a bit hard to ignite
heavy fuel with a   sparkplug, so maybe they are actually running
diesel compression.

Higher and higher compression gives a diminishing point of
return. Raise   the compression from 5:1 to 7:1 and you will get a
tremedeous good   return, raise it from 7:1 to 9:1 and you will get
a decent return, raise   it from 9:1 to 11:1 and you will get a very
small return.

Part of the gain is not from raising the compression in itself,
but the   increased ability the engine will get, to clean out spent
and inert gas   from it's last work stroke.   I can see two areas
the rotary could need an improvement on, bigger   stroke, the stroke
it has is very small, and are depending on the   difference in the
center of the shaft to the center of the ofset roll   shaft each
rotor is spinning around.

From what I understand you are saying, they are working out the
geometry better now.

The up and down bobbing triangular center body. it doesnt
describe a   true rotation, but changes it's position where the
center of mass will   be shifting between two extremes, and as I
understand, it is made of   steel, right now. If you take a body
like that, everytime two of the   three corners in the triangular
centerbody , are on the outside, the   force inceases.

The energy it takes to change that mass back and forth between
those two   main positions, got to be huge, ..as Newton says,
 everytime you change   direction, you pay for it in lost energy.

I don't know how it compare with forces in a piston engine other
than a   lose comparison, as in a piston engine, the main mass that
is   reciprocating is a steel rod, and an aluminum piston, part of
the steel   rod is follwing the crank in a true circle, the crank
itself is   follwing a true circle. You spin that up to maybe 3000
RPM, on freeay   speed, while the rotary has a much heavier piece
that have a shorter   stroke, but much heavier mass, and perhaps
twice the rotation...force   needed at twice the RPM is not linear,
 ...I dont know the exact number   as the baseline is an estimate,
but I dont think that four times the   force is too much out of line.

If a rotary would be connected up to an electric motor, and the force
was measured to rotate it, the lower RPM bands would probably be very
good, , but the force needed to spin it in the upper bands where the
rotary works best, must be terrible.

I can understand it is a matter of structural integrity, but the weight
on that tringular rotor has to come down, and I don't know what material
that is lighter that can substitute the steel and still dont have
fatigugue problems, as it is a critical component.

Titanium perhaps, or perhaps a steel casing filled with aluminum,
either   way, that up and down bobbing piece of steel is stealing a
lot of energy   to do that movement.

True rotating parts can conserve and store energy, and even if a piston
engine has a lot of parts to it that moves, actually most of it's
rotating mass are both balanced and in true rotation, the
majority of   the moving mass in a rotary is not in true rotation,
...therefore in   direct correlation to it's mass and speed, it will
steal rotational   energy.... therefore to get a distinct leap of
efficiency with the   rotary engine, the mass of that part has to
come down drastically.

How to do it and still keep the structural integrity...I don't
even want   to think about it.

I bet ya in fifteen years from now we can order from Edelbrock a rotary
replacement that is made of a material we can't pronounce.

Roger

"The up and down bobbing triangular center body."

There is no up and down Roger. A common mistake many make.
The rotor CG orbits around the center of the e-shaft much like
the earth orbits the sun. That is why it is sometimes called
a planetary engine. Have you read the Kitplanes article yet?

Here is a good one to read as well.

http://www.rotaryeng.net/how-wank-works.html

"Actually what is happening is the center or CG of the rotor is
moving in a
circle around the center of the output shaft while the output
shaft rotates."

"Since there are no reciprocation parts what so ever it is
possible to   completely balance the Wankel engine just like a
turbine or electric motor and   unlike any piston engine despite
some claims to the contrary. The rotor is   balanced around it own
axis. The front rotor balances the rear rotor as they are   180
degrees apart on the output shaft. That leaves a small couple which
is   finally completely balanced by the counter weights."

Also go on youtube and watch many Wankel animations as there are
dozens.

The only limitations on the RPM of a rotary are due to centrifugal
load of the rotor weight on the e-shaft rotor bearing.

Paul Lamar
--
I'm no expert, but the two areas in which the Wankel would need to be
improved to significantly improve BSFC are
1) Reduction of waste energy in the exhaust (higher in the rotary than
in a piston, as evidenced by higher EGTs)

2) Reduction of waste heat lost to the housing due to the relatively
inefficient shape of the combustion area (long, wide, and very thin
in a rotary= lots of surface area-to-volume, relatively compact and
cylindrical in a piston engine=less surface area per volume.

It seems 1) could be reduced by turbocompounding, and 2) might be
somewhat reduced by optimizing the engine geometry, but real
improvements here await development of a practical ceramic engine or
other material breakthrough  (or some miracle way of recovering that
low-quality waste heat in the cooling water--very unlikely).

Mark W.

The higher EGT is due to the fact there are no exhaust valves
to absorb some of the heat. The RX8 engine is proof as the exhaust must
make a right angle to exit so some of that waste heat goes
into the cooling system and the EGT is a couple of hundred
degrees F cooler.

In the R3350 turbo compound engine 22% of the total energy in
the exhaust went into the exhaust valve. Almost 50% of the kinetic
energy went into the exhaust valve. That is why a rotary is so
noisy. It is also why it makes an ideal turbo compound engine.

I am beginning to think the old surface area to volume ratio reason
is invalid. Both the 16x and the Wankel SuperTec engines have
worse  surface area to volume ratios yet are more efficient
than the current geometry.

Paul Lamar


There could be a difference in the area if it is the end plates or the rotor
housing. If the fuel has a tendency to be pushed to the rotor housing causing
poor burn the solution may be in a narrower housing with greater eccentricity.
The side housing area is larger but may not affect the burn the same. Also in
reading, the flame does not get all the way to the sides of rotors more than
76mm wide. This seems to explain a lot of why Mazda would narrow the housings.
It gives more complete burn the same as the 3rd plugs in the 26B Le Mans engine.

Dale Davies

Actually the fuel being pushed to the rotor housing is an advantage
as the engine will run with 20:1 air fuel ratio unlike a piston engine
and gain BSFC in the bargain.

I think you are right on the rotor width but that does not take
into consideration  two sparks plugs side by side in the leading
position. Austro engines use this trick on their wider rotors.

Read Norton geometry.

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.