Compression ratio and expansion ratio.
Yes, the ideal would be to be able to catch every piece of work in
the heat cycle.
If we would have a ballon of indestructable material, fill it with
gasoline and air to the ratio we are using in engines, ignite it, let it
go bang, and let it expand, until the gasses by it's own expansion,
reaches peak expansion. We would have a pretty big baloon now. then we
would get a period of contraction, that will continue until the hot
gasses has cooled down to ambient temperature. When we are done with
that we will hold a smaller baloon with all the burnt gasses from the
original gasoline and air charge, that will have ambient pressure and
ambient temperature.
The trick is to catch all that work in any engine.
Here we get in to the world of compromizes.
We usually only catch a small part of that cycle, the high pressure
part, we don't even think of trying to catch the contraction part, and
there is good reasons for it.
The longer on the heat cycle we want to catch the pressure, the lower
and lower pressure we have to recover. The lower in the cycle we want to
go, the more expansion space we need to accomodate, but also increase
the internal volume of the engine, to accomodate for the last pieces of
pressure we need to recover.
This part is important as it will determine the size of an engine. Lower
pressure recovery on the cycle will add a time factor to it also, and
each combustion cycle will have to be slower, with other words big
displacement and low RPM.
The bigger dispacement the better heat recovery further down on the
pressure scale. a pressure of 5 PSI will not do much work on a small
piston surface, but if the surface is big enough to throw a party on it,
those 5 PSI will do a good work on that surface.
See it like this, if you have 55 engines that have a one gallon
displacement ( pretty big to start up with, but ok just to show) and we
have an engine with 55 gallon displacement, (oildrum size) one can think
that 55 one gallon engines will be as efficient as one 55 gallon engine,
but the thermal efficiency of the 55 gallon engine is so much better.
It is a surface thing.
Take a cylinder surface that gives a one gallon displacement, and
flatten it out...now take 55 of those surfaces, and compare it with the
surface of a ONE 55 gallon oildrum, and you will find that all those one
gallon engine surfaces combined will be so much more than the surface
from one single 55 gallon drum.
That is a lot of heatsurfaces that heat will dissaper into, making no work.
For those that have some interest in this, you can go to any search
engine, and look up The Worlds Biggest Diesel Engine, and you will see a
14 cylinder Wirthsilla ship engine, built in Japan, that is so big that
there are handlebars going into the crankhouse.
It's doing tops 108 RPM and will produce over 100.000 HP, but the fact
that will connect this engine with this topic is that it is over 50%
thermal efficient.
Compression ratio and expansion ratio is , granted, two different
things, but very hard to practically distinguish.
For a while in EU especially a couple of decades after the war, some
countries, especially then France and England, had a tax system on cars
that put them in different tax categories depending on the engine size.
( French CV system, had a Citroen CV2...great car) , now Britain at the
time had their engine tax size based on the bore size, with the result
that out of Britan around that era there was a lot of small cars that
came on the market, with very small bore and very long stroke, in order
to try to get more displacement out of the engine for any given bore.
That, on the first look, might look like the perfect way to get a longer
expansion rate, but it just showed that those engines were running with
very high piston speed., and was very limited engines. Oversquared
engines, ( stroke longer than the bore diameter) , have inherently a
higher wear and tear, especially on piston, piston rings, and bore.
Undersquared engines, (bore bigger than the stroke) can rev higher and
still have decent piston speed, and will be able to exchange gas more
often, thus do more work, thus give more power, thus can be made smaller
and more lightweight etc etc, so engines that are square or undersquare
have more development possibility, and the long stroked engines from the
post war European tax environment existed only because of tax
incentives, and had less technical base for it's existence.
There was if I remeber the timeline right, a debate 15 or 18 years ago
on this particular issue in Hot Rod circles, where the proponents of
stroked engines held onto the position that they were more "torque"
engines, ( to translate, more efficent in follow the whole heatcycle),
and that lead to some to test the theory back and forth ( hey it has
been tested long before that, but to some Hot Rodeers, you can't tell
them anything, they have to reinvent the wheel), and of course they came
up with the conclusion that was long known....a stoked engine is getting
it's increased power from increased displacement, not a better heat
cycle,, if you increase the dispacement from a bore or a stroke you will
get some smaller differences in engine caracteristics, but basically you
will get the same result.
Compression ratio and expansion ratio is so closely related that it is
hard to distinguish the two in practical applications. Because of the
fuel we use, we can't go up on the compression ratio that much. A
continous increased compression ratio will give diminishing results. If
you raise it from 4:1 to 6 :1 you will get excellent return. If you
rasie it from 10:1 to 12:1, you will hardly get any return, still in
both occasions you raised the compression ratio two points.
A combustion engine runs ( depending on gasoline, rotary, or diesel) in
the 25 to 35% efficiency range , some better some worse.
It is a choice we are doing, if we want to catch high pressure often,
and release the remaining pressure, if we instead can quickly grab
another high pressure to catch for a while, that makes for a small and
compact source of high power.
Or if we want to try to catch more of the heat cycle, in a bigger ( much
bigger preferably) and slower cycling engine.
We could theoretically make an engine that goes through the whole heat
cycle, and even catch the inherent energy from the condensation part and
thus get vaccum.
1 unit of water will produce a volume of about 1850 units of hydrogen
and oxygen gas. Feed it into an engine and ignite,...the hydrogen and
oxygen combines in a bang, and makes superheated steam, the piston goes
down, cools down the charge, and we get condensation, and the original
1850 units of gas ( now burned and expanded even more) will now go back
to it's original 1 unit of water, and we get a vaccum, that could act
upon a piston to "suck it up" , to TDC and we could start the cycle again.
Problem is, this is something that maybe has to be big enough that you
could walk on the top of the piston, and the cycle has to be , maybe 2
or 3 RPM. Remember at the end of the expansion phase the time factor
increases, the fist part of expansion is a flash, but the last part of
expansion is a snail.
If we only catch the first part of the expansion, the powerful flash,
and can do it over and over, very quick, we will get a small powerful
engine ( that we can fly with)
So the point I am getting to is that while it is in itself a worth while
operation to try to catch as much as possible from the heat cycle, ( and
there is a lot of gizmos, hop ups and other things out there from a
horde of people, or companies that are trying their best to do so, )
doing it in the engine itself, is very hard, if the engine has to do
what it has to do.
It's originally designed to catch only the very first part of the
powerful heat cycle. Even if there is more left of the heat cycle, the
design is not there to catch it.
If we want something that is designed with the effort of trying to catch
a whole heat cycle, you have to design something else. It can't look
like our small compact high rev high power piston or rotary engines.
Most efforts on the aftermarket or industry developments are aimed at
either increasing the pressure, or to make the current heat pressure
window more efficent, not prolonging the effort to catch the whole heat
cycle.
Improvements can be made and are made, but the development seems to be
incremental, and in small steps at a time.
The piston engine that have had a 100 year development history from
Fords Tin Lizzy to todays engines have never in it's history made a
giant leap at any point in history. (you got 20 mpg in a model T).
Despite electronics, better machining and better material, the effciency
numbers our forefathers was tossing to each other, is not far fetced
numbers today. The engines ARE better today, but there are no gigant
leaps here. the basic original design is pretty much the same.
Most engines to be practial for us has to be small, lightweight have
high rev, catch the high pressure part of the heat cycle, dismiss the
low pressure part, ( could be used to spool a turbo......why not an
alternator) , and continue to catch the high pressure part of the cycle,
and do it often....thus we have the powerplant we want.
So if we want what we want, we have to waste or sacrifice some
things....the low pressure...and as is easily recognizeable, it's still
part of the heat cycle that powers the engine. However the heat cycle
have now change personality, from being Arnold Schwartsenegger in the
engine, it is now a sick noisy smelly bum, that is hard to get any work
out of...so we waste him.
If it is unbearable to live with that,...well guess it is time to order
your Wirtsilla 14 cyl diesel, then at least you will get over the 50%
efficiency number.
Roger
We are not designing new engines here. We are mainly installing
Wankel engines in aircraft and dealing with the associated accessory
problems such as cooling, intake configurations, fuel systems and ignition.
Something the average home builder must and can deal with.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.