Subject: Compression ratio and expansion ratio. New engines??
From: Rotary Engine
Date: 1/16/2011, 10:09 AM
To: AAA Put this in the To box

 Compression ratio and expansion ratio.

 Yes, the ideal would be to be able to catch every piece of work in
 the heat cycle.

 If we would have a ballon of indestructable material, fill it with
 gasoline and air to the ratio we are using in engines, ignite it, let it
 go bang, and let it expand, until the gasses by it's own expansion,
 reaches peak expansion.  We would have a pretty big baloon now. then we
 would get a period of contraction, that will continue until the hot
 gasses has cooled down to ambient temperature. When we are done with
 that we will hold a smaller baloon with all the burnt gasses from the
 original gasoline and air charge, that will have ambient pressure and
 ambient temperature.

 The trick is to catch all that work in any engine.

 Here we get in to the world of compromizes.

 We usually only catch a small part of that cycle, the high pressure
 part, we don't even think of trying to catch the contraction part,  and
 there is good reasons for it.

 The longer on the heat cycle we want to catch the pressure, the lower
 and lower pressure we have to recover. The lower in the cycle we want to
 go, the more expansion space we need to accomodate, but also increase
 the internal volume of the engine, to accomodate for the last pieces of
 pressure we need to recover.

 This part is important as it will determine the size of an engine. Lower
 pressure recovery on the cycle will add a time factor to it also, and
 each combustion cycle will have to be slower, with other words big
 displacement and low RPM.

 The bigger dispacement the better heat recovery further down on the
 pressure scale. a pressure of 5 PSI will not do much work on a small
 piston surface, but if the surface is big enough to throw a party on it,
 those 5 PSI will do a good work on that surface.

 See it like this,  if you have 55 engines that have a one gallon
 displacement ( pretty big to start up with, but ok just to show) and we
 have an engine with 55 gallon displacement, (oildrum size) one can think
 that 55 one gallon engines will be as efficient as one 55 gallon engine,
 but the thermal efficiency of the 55 gallon engine is so much better.

 It is a surface thing.

 Take a cylinder surface that gives a one gallon displacement, and
 flatten it out...now take 55 of those surfaces, and compare it with the
 surface of a ONE 55 gallon oildrum, and you will find that all those one
 gallon engine surfaces combined will be so much more than the surface
 from one single 55 gallon drum.

 That is a lot of heatsurfaces that heat will dissaper into, making
 no work.

 For those that have some interest in this, you can go to any search
 engine, and look up The Worlds Biggest Diesel Engine, and you will see a
 14 cylinder Wirthsilla ship engine, built in Japan, that is so big that
 there are handlebars going into the crankhouse.

 It's doing tops 108 RPM and will produce over 100.000 HP, but the fact
 that will connect this engine with this topic is that it is over 50%
 thermal efficient.

 Compression ratio and expansion ratio is , granted, two different
 things, but very hard to practically distinguish.

 For a while in EU especially a couple of decades after the war, some
 countries, especially then France and England, had a tax system on cars
 that put them in different tax categories depending on the engine size.
 ( French CV system, had a Citroen CV2...great car) , now Britain at the
 time had their engine tax size based on the bore size, with the result
 that out of Britan around that era there was a lot of small cars that
 came on the market, with very small bore and very long stroke, in order
 to try to get more displacement out of the engine for any given bore.

 That, on the first look, might look like the perfect way to get a longer
 expansion rate, but it just showed that those engines were running with
 very high piston speed., and was very limited engines. Oversquared
 engines, ( stroke longer than the bore diameter) , have inherently a
 higher wear and tear, especially on piston, piston rings, and bore.

 Undersquared engines, (bore bigger than the stroke) can rev higher and
 still have decent piston speed, and will be able to exchange gas more
 often, thus do more work, thus give more power, thus can be made smaller
 and more lightweight etc etc, so engines that are square or undersquare
 have more development possibility, and the long stroked engines from the
 post war European tax environment existed only because of tax
 incentives, and had less technical base for it's existence.

 There was if I remeber the timeline right, a debate 15 or 18 years ago
 on this particular issue in Hot Rod circles, where the proponents of
 stroked engines held onto the position that they were more "torque"
 engines, ( to translate, more efficent in follow the whole heatcycle),
 and that lead to some to test the theory back and forth ( hey it has
 been tested long before that, but to some Hot Rodeers, you can't tell
 them anything, they have to reinvent the wheel), and of course they came
 up with the conclusion that was long known....a stoked engine is getting
 it's increased power from increased displacement, not a better heat
 cycle,, if you increase the dispacement from a bore or a stroke you will
 get some smaller differences in engine caracteristics, but basically you
 will get the same result.

 Compression ratio and expansion ratio is so closely related that it is
 hard to distinguish the two in practical applications. Because of the
 fuel we use, we can't go up on the compression ratio that much. A
 continous increased compression ratio will give diminishing results. If
 you raise it from 4:1 to 6 :1 you will get excellent return. If you
 rasie it from 10:1 to 12:1, you will hardly get any return, still in
 both occasions you raised the compression ratio two points.

 A combustion engine runs ( depending on gasoline, rotary, or diesel) in
 the 25 to 35% efficiency range , some better some worse.

 It is a choice we are doing, if we want to catch high pressure often,
 and release the remaining pressure, if we instead can quickly grab
 another high pressure to catch for a while, that makes for a small and
 compact source of high power.

 Or if we want to try to catch more of the heat cycle, in a bigger ( much
 bigger preferably) and slower cycling engine.

 We could theoretically make an engine that goes through the whole heat
 cycle, and even catch the inherent energy from the condensation part and
 thus get vaccum.

 1 unit of water will produce a volume of about 1850 units of hydrogen
 and oxygen gas. Feed it into an engine and ignite,...the hydrogen and
 oxygen combines in a bang, and makes superheated steam, the piston goes
 down, cools down the charge, and we get condensation, and the original
 1850 units of gas ( now burned and expanded even more) will now go back
 to it's original 1 unit of water, and we get a vaccum, that could act
 upon a piston to "suck it up" , to TDC and we could start the cycle
 again.

 Problem is, this is something that maybe has to be big enough that you
 could walk on the top of the piston, and the cycle has to be , maybe  2
 or 3 RPM. Remember at the end of the expansion phase the time factor
 increases, the fist part of expansion is a flash, but the last part of
 expansion is a snail.

 If we only catch the first part of the expansion, the powerful flash,
 and can do it over and over, very quick, we will get a small powerful
 engine ( that we can fly with)

 So the point I am getting to is that while it is in itself a worth while
 operation to try to catch as much as possible from the heat cycle, ( and
 there is a lot of gizmos, hop ups and other things out there from a
 horde of people, or companies that are trying their best to do so, )
 doing it in the engine itself, is very hard, if the engine has to do
 what it has to do.

It's originally designed to catch only the very first part of the
 powerful heat cycle. Even if there is more left of the heat cycle, the
 design is not there to catch it.

 If we want something that is designed with the effort of trying to catch
 a whole heat cycle, you have to design something else. It can't look
 like our small compact high rev high power piston or rotary engines.

 Most efforts on the aftermarket or industry developments are aimed at
 either increasing the pressure, or to make the current heat pressure
 window more efficent, not prolonging the effort to catch the whole heat
 cycle.

 Improvements can be made and are made, but the development seems to be
 incremental, and in small steps at a time.

 The piston engine that have had a 100 year development history from
 Fords Tin Lizzy to todays engines have never in it's history made a
 giant leap at any point in history. (you got 20 mpg in a model T).

 Despite electronics, better machining and better material, the effciency
 numbers our forefathers was tossing to each other, is not far fetced
 numbers today. The engines ARE better today, but there are no gigant
 leaps here. the basic original design is pretty much the same.

 Most engines to be practial for us has to be small, lightweight have
 high rev, catch the high pressure part of the heat cycle, dismiss the
 low pressure part, ( could be used to spool a turbo......why not an
 alternator) , and continue to catch the high pressure part of the cycle,
 and do it often....thus we have the powerplant we want.

 So if we want what we want, we have to waste or sacrifice some
 things....the low pressure...and as is easily recognizeable, it's still
 part of the heat cycle that powers the engine. However the heat cycle
 have now change personality, from being Arnold Schwartsenegger in the
 engine, it is now a sick noisy smelly bum, that is hard to get any work
 out of...so we waste him.

 If it is unbearable to live with that,...well guess it is time to order
 your Wirtsilla 14 cyl diesel, then at least you will get over the 50%
 efficiency number.

 Roger

 We are not designing new engines here. We are mainly installing
 Wankel engines in aircraft and dealing with the associated accessory
 problems such as cooling, intake configurations, fuel systems  and
 ignition.

Something the average home builder must and can deal with.

 Paul Lamar


Roger

A good explanation of the heat cycle... and the reason why Paul is so
adamant about
turbocompounding the waste heat of the exhaust cycle to get a 20%
increase in efficiency.

Dan F



-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.