Subject: Compression ratio and expansion ratio. New engines??
From: Rotary Engine
Date: 1/16/2011, 1:46 PM
To: AAA Put this in the To box


Compression ratio and expansion ratio.

Yes, the ideal would be to be able to catch every piece of work in
the heat cycle.

If we would have a ballon of indestructable material, fill it with
gasoline and air to the ratio we are using in engines, ignite it,
let it   go bang, and let it expand, until the gasses by it's own
expansion,   reaches peak expansion.  We would have a pretty big
baloon now. then we   would get a period of contraction, that will
continue until the hot   gasses has cooled down to ambient
temperature. When we are done with   that we will hold a smaller
baloon with all the burnt gasses from the   original gasoline and
air charge, that will have ambient pressure and   ambient temperature.

The trick is to catch all that work in any engine.

Here we get in to the world of compromizes.

We usually only catch a small part of that cycle, the high
pressure   part, we don't even think of trying to catch the
contraction part,  and   there is good reasons for it.

The longer on the heat cycle we want to catch the pressure, the lower
and lower pressure we have to recover. The lower in the cycle we
want to   go, the more expansion space we need to accomodate, but
also increase   the internal volume of the engine, to accomodate for
the last pieces of   pressure we need to recover.

This part is important as it will determine the size of an
engine. Lower   pressure recovery on the cycle will add a time
factor to it also, and   each combustion cycle will have to be
slower, with other words big   displacement and low RPM.

The bigger dispacement the better heat recovery further down on
the   pressure scale. a pressure of 5 PSI will not do much work on a
small   piston surface, but if the surface is big enough to throw a
party on it,   those 5 PSI will do a good work on that surface.

See it like this,  if you have 55 engines that have a one gallon
displacement ( pretty big to start up with, but ok just to show)
 and we   have an engine with 55 gallon displacement, (oildrum size)
one can think   that 55 one gallon engines will be as efficient as
one 55 gallon engine,   but the thermal efficiency of the 55 gallon
engine is so much better.

It is a surface thing.

Take a cylinder surface that gives a one gallon displacement, and
flatten it out...now take 55 of those surfaces, and compare it
with the   surface of a ONE 55 gallon oildrum, and you will find
that all those one   gallon engine surfaces combined will be so much
more than the surface   from one single 55 gallon drum.

That is a lot of heatsurfaces that heat will dissaper into, making
no work.

For those that have some interest in this, you can go to any
search   engine, and look up The Worlds Biggest Diesel Engine, and
you will see a   14 cylinder Wirthsilla ship engine, built in Japan,
that is so big that   there are handlebars going into the crankhouse.

It's doing tops 108 RPM and will produce over 100.000 HP, but the
fact   that will connect this engine with this topic is that it is
over 50%   thermal efficient.

Compression ratio and expansion ratio is , granted, two different
things, but very hard to practically distinguish.

For a while in EU especially a couple of decades after the war, some
countries, especially then France and England, had a tax system
on cars   that put them in different tax categories depending on the
engine size.
( French CV system, had a Citroen CV2...great car) , now Britain
at the   time had their engine tax size based on the bore size, with
the result   that out of Britan around that era there was a lot of
small cars that   came on the market, with very small bore and very
long stroke, in order   to try to get more displacement out of the
engine for any given bore.

That, on the first look, might look like the perfect way to get a
longer   expansion rate, but it just showed that those engines were
running with   very high piston speed., and was very limited
engines. Oversquared   engines, ( stroke longer than the bore
diameter) , have inherently a   higher wear and tear, especially on
piston, piston rings, and bore.

Undersquared engines, (bore bigger than the stroke) can rev
higher and   still have decent piston speed, and will be able to
exchange gas more   often, thus do more work, thus give more power,
 thus can be made smaller   and more lightweight etc etc, so engines
that are square or undersquare   have more development possibility,
 and the long stroked engines from the   post war European tax
environment existed only because of tax   incentives, and had less
technical base for it's existence.

There was if I remeber the timeline right, a debate 15 or 18
years ago   on this particular issue in Hot Rod circles, where the
proponents of   stroked engines held onto the position that they
were more "torque"   engines, ( to translate, more efficent in
follow the whole heatcycle),   and that lead to some to test the
theory back and forth ( hey it has   been tested long before that,
but to some Hot Rodeers, you can't tell   them anything, they have
to reinvent the wheel), and of course they came   up with the
conclusion that was long known....a stoked engine is getting   it's
increased power from increased displacement, not a better heat cycle,, if you increase the dispacement from a bore or a stroke you will
get some smaller differences in engine caracteristics, but
basically you   will get the same result.

Compression ratio and expansion ratio is so closely related that
it is   hard to distinguish the two in practical applications.
Because of the   fuel we use, we can't go up on the compression
ratio that much. A   continous increased compression ratio will give
diminishing results. If   you raise it from 4:1 to 6 :1 you will get
excellent return. If you   rasie it from 10:1 to 12:1, you will
hardly get any return, still in   both occasions you raised the
compression ratio two points.

A combustion engine runs ( depending on gasoline, rotary, or
diesel) in   the 25 to 35% efficiency range , some better some worse.

It is a choice we are doing, if we want to catch high pressure
often,   and release the remaining pressure, if we instead can
quickly grab   another high pressure to catch for a while, that
makes for a small and   compact source of high power.

Or if we want to try to catch more of the heat cycle, in a bigger
( much   bigger preferably) and slower cycling engine.

We could theoretically make an engine that goes through the whole
heat   cycle, and even catch the inherent energy from the
condensation part and   thus get vaccum.

1 unit of water will produce a volume of about 1850 units of hydrogen
and oxygen gas. Feed it into an engine and ignite,...the hydrogen
and   oxygen combines in a bang, and makes superheated steam, the
piston goes   down, cools down the charge, and we get condensation,
 and the original   1850 units of gas ( now burned and expanded even
more) will now go back   to it's original 1 unit of water, and we
get a vaccum, that could act   upon a piston to "suck it up" , to
TDC and we could start the cycle   again.

Problem is, this is something that maybe has to be big enough
that you   could walk on the top of the piston, and the cycle has to
be , maybe  2   or 3 RPM. Remember at the end of the expansion phase
the time factor   increases, the fist part of expansion is a flash,
 but the last part of   expansion is a snail.

If we only catch the first part of the expansion, the powerful
flash,   and can do it over and over, very quick, we will get a
small powerful   engine ( that we can fly with)

So the point I am getting to is that while it is in itself a
worth while   operation to try to catch as much as possible from the
heat cycle, ( and   there is a lot of gizmos, hop ups and other
things out there from a   horde of people, or companies that are
trying their best to do so, )   doing it in the engine itself, is
very hard, if the engine has to do   what it has to do.
It's originally designed to catch only the very first part of the
powerful heat cycle. Even if there is more left of the heat cycle,
 the   design is not there to catch it.

If we want something that is designed with the effort of trying
to catch   a whole heat cycle, you have to design something else. It
can't look   like our small compact high rev high power piston or
rotary engines.

Most efforts on the aftermarket or industry developments are
aimed at   either increasing the pressure, or to make the current
heat pressure   window more efficent, not prolonging the effort to
catch the whole heat   cycle.

Improvements can be made and are made, but the development seems
to be   incremental, and in small steps at a time.

The piston engine that have had a 100 year development history
from   Fords Tin Lizzy to todays engines have never in it's history
made a   giant leap at any point in history. (you got 20 mpg in a
model T).

Despite electronics, better machining and better material, the effciency
numbers our forefathers was tossing to each other, is not far fetced
numbers today. The engines ARE better today, but there are no gigant
leaps here. the basic original design is pretty much the same.

Most engines to be practial for us has to be small, lightweight have
high rev, catch the high pressure part of the heat cycle, dismiss
the   low pressure part, ( could be used to spool a turbo......why
not an   alternator) , and continue to catch the high pressure part
of the cycle,   and do it often....thus we have the powerplant we want.

So if we want what we want, we have to waste or sacrifice some
things....the low pressure...and as is easily recognizeable, it's
still   part of the heat cycle that powers the engine. However the
heat cycle   have now change personality, from being Arnold
Schwartsenegger in the   engine, it is now a sick noisy smelly bum,
 that is hard to get any work   out of...so we waste him.

If it is unbearable to live with that,...well guess it is time to
order   your Wirtsilla 14 cyl diesel, then at least you will get
over the 50%   efficiency number.

Roger

We are not designing new engines here. We are mainly installing
Wankel engines in aircraft and dealing with the associated accessory
problems such as cooling, intake configurations, fuel systems  and
ignition.
Something the average home builder must and can deal with.

Paul Lamar

Roger

A good explanation of the heat cycle... and the reason why Paul is so
adamant about
turbocompounding the waste heat of the exhaust cycle to get a 20%
increase in efficiency.

Dan F


I must admit we have been having some interesting discussions about a couple
of topics. This is in my mind how innovation gets a jump start.

The latest Road and Track has an article on the Hennesy Venom. Yes I know this
is about rotor motors in AC. Hennesy's crew had done one thing and were then
considering what next. The Lotus Exige came up and was at first passed by.
Someone did a drawing and a few days later they came up with the idea to put a
1200 HP twin turbo in. Now can you imagine that car with a turbo compound 20B.
Or get really silly and turbo compound an all Al 26B? Now that might give a
slight green tint to the skin!

Dale Davies


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.