They don't counter rotate. They both rotate in the same direction.
The two rotor is basically two one rotors 180 degrees out of phase
on the same eccentric shaft. They static balance each other.
There is no difference in the way they work. The forces are
the same. The one rotor is easy to balance as the two counter
weights just balance the weight of the rotor and the eccentric
lobe. There is no couple. The only forces we must deal with are
centrifugal forces on the rotor moving in a circle around the
center of the e-shaft.
"Put it in left position, and put the rotary with the flat side towards
left, ( two horns out) and you will have more mass to the left of
the CENTER ROTATING SHAFT than you will if you put the rotary in the
position where it has one horn out."
Yes but that does not matter. I say so what? :)
The eccentric lobe will be out there too.
I suddenly see your problem understanding this.
You are forgetting the one rotor balance weights on the other side
of the e-shaft center. The one rotor balance weights are always
opposite the eccentric lobe. When you put one horn out so
too will be the balance weights but no eccentric lobe.
Unfortunately there are a lot of one rotor animations out there that
don't show the counter weights so it is easy to get confused.
The CG of the rotor and it's total mass is all the e-shaft sees.
The rotor is balanced about its center at the factory.
Why a triangle is in balance about it's center is another subject.
I don't know of anybody in that neck of the woods with a rotary.
Perhaps I am wrong and somebody will speak up that has some
engine parts they can show off.
Paul Lamar
Paul,
Greeeeat, were getting to it, finally we start to be on the same page,
were not there yet, but aaaalmost.
We can do this......
I do fully understand that a 3 sided object rigged the way it is in a
rotaty will be in balance on its ofset shaft, no matter what position it
will be in. That part is and will be in balance no matter what we do to
it, that is no problem.
I also understand that there might be a counter balance for the
eccentric shaft, and in that way we can take off the rotor, and the
center shaft will balance.
If the center shaft is balanced , with weights that will perfectly
balance the rotary assembly , and the rotary assembly is balanced around
it's triangular body, then we have a perfect balance between the counter
weights , the triangular body , no matter what position it is in, but we
dont necessarily have a balance between the changing mass between the
rotary and the center of the rotating center shaft''.
Imagine a see saw, very strong seesaw, where a child and a cow is
sitting on one end, and on the other end is also perfectly balanced
child and a cow.
That is how a static balance is described, where the rotary assembly,
the ofset center, and the counter weights should look.
The problem here is that one kid is a very strong kid, so he took his
cow in the tail and are swinging it over his head.
What I am trying to establish is change of mass location in relation to
the CENTER shaft.
With this new understading now.....like before ....place the offset shaft
to the left, ...and start in position one... the flat side of the rotaty
to the left...and look at the amount of mass to the left of the
vertical centerline of the CENTER SHAFT....not the offset shaft.
Ok now ...with the ofset shaft still to your left. Rotate the triangular
rotary body so one point of the body points to the left and you have a
flat side to the right.
Now in position two...again look at the vertical centerline of the CETER
SHAFT....not the ofset shaft, and tell me how much mass there is to the
left of the centerline.
Is there any difference in mass between position one and position two?
Roger
"If the center shaft is balanced, with weights that will perfectly
balance the rotary assembly, and the rotary assembly is balanced around
it's triangular body, then we have a perfect balance between the counter
weights, the triangular body, no matter what position it is in, but we
don't necessarily have a balance between the changing mass between the
rotary and the center of the rotating center shaft''."
Yes we do. If there were no balance in any position we would have a vibration.
THERE IS NO VIBRATION!! Nada, zero, nothing! The balance weights balance the
eccentric lobe AND the weight of the rotor perfectly in all positions.
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.