Paul,
I live in central Ca, closest airport is Columbia, next closest is
Angels Camp or Calaveras airport. Closest town is Sonora.
You showed a model of a rotary that has two counter rotating rotaries,
...no that's not what I ment.
I ment the forces that are occurring in one unit.
I ment the forces that are occurring between the components of the basic
unit.
One centershaft....one eccentric shaft....one rotary.
If two units are mounted opposite to each other, they will off course
balance each other out. they will balance out in the same sense as if
we were to put pistons in a piston engine opposing each other, but the
reciprocating force is still there, and if there is a reciprocating
force , even if they balance each other out, it is a force that will
increase with RPM, and that is the issue here.
.....so sorry you misunderstood me here,...no I am not talking about a
possibility to balance out an engine with an opposed piston or rotary,
lets go back to ONE rotary.....I am looking at the forces that is
existing in it's basic configuration.
Put it in left position, and put the rotary with the flat side towards
left, ( two horns out) and you will have more mass to the left of
the CENTER ROTATING SHAFT than you will if you put the rotary in the
position where it has one horn out.
Paul, it's of no use to say that you'r sorry that I don't understand,
and refere me to more pictures or models those will only will reinforce
my observation.
You have been working with this for years and years and years, and have
come to an understanding of this engine that may be granted to very few
people, and I see something that, as I see it, is contrary but obvious
and uncompromisable.
With the long and exhaustive experience you have with the rotary, I am
up against authority here, but still, as my observation differs, I can't
deny my own understanding of it.
I think we are passed videos and plastic models, and need to talk. The
blog is just too limited at this stage. ( I also want to ask you about
the 555 system a bit at the same time)
Because of what I work with, I am up very much at night, sometimes to
early morning hours...do you have a phone number I can reach you on.
Roger
They don't counter rotate. They both rotate in the same direction.
The two rotor is basically two one rotors 180 degrees out of phase
on the same eccentric shaft. They static balance each other.
There is no difference in the way they work. The forces are
the same. The one rotor is easy to balance as the two counter
weights just balance the weight of the rotor and the eccentric
lobe. There is no couple. The only forces we must deal with are
centrifugal forces on the rotor moving in a circle around the
center of the e-shaft.
"Put it in left position, and put the rotary with the flat side towards
left, ( two horns out) and you will have more mass to the left of
the CENTER ROTATING SHAFT than you will if you put the rotary in the
position where it has one horn out."
Yes but that does not matter. I say so what? :)
The eccentric lobe will be out there too.
I suddenly see your problem understanding this.
You are forgetting the one rotor balance weights on the other side
of the e-shaft center. The one rotor balance weights are always
opposite the eccentric lobe. When you put one horn out so
too will be the balance weights but no eccentric lobe.
Unfortunately there are a lot of one rotor animations out there that
don't show the counter weights so it is easy to get confused.
The CG of the rotor and it's total mass is all the e-shaft sees.
The rotor is balanced about its center at the factory.
Why a triangle is in balance about it's center is another subject.
I don't know of anybody in that neck of the woods with a rotary.
Perhaps I am wrong and somebody will speak up that has some
engine parts they can show off.
Paul Lamar
All this talk of balance reminds me of the demonstration my Dad use to
do with his 70's Mazda Pickup he had.
Open the hood and set a nickel (on edge) on the flat spot near where the
12A (13B now) is cast into the rotor housing and rev the engine it
would just sit there like the engine was not even running. Very
convincing of the smoothness of a rotary.
Brian
Thank you Brian :)
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.