Subject: torsional vibration
From: Rotary Engine
Date: 1/17/2011, 9:24 AM
To: AAA Put this in the To box


Now that torsional vibration is being discussed let's get back to the
single rotor version. Does anyone know what would be a satisfactory
torsional vibration damper for these as they don't have the overlapping
power pulses from the other rotor to smooth things out i.e. how much
flywheel do they need?

I note that Richard Sohn uses a Hirth reduction box on his - I think
they use a rubber dough nut like the Rotax 2 stroke reductions?

Are the rubber isolators used by Tracey suitable for the frequencies
of a single rotor, let alone the increased amplitude with no
overlapping
power strokes?

It would be nice if the collected wisdom on single rotors was available
in one place, after all about 100 to 120 HP (Rotax 912 to 914
territory) is commonly needed for very light aircraft. I must admit
I'm not all that impressed with my 912, it only has 29.9 hours on it,
the fuel pump failed - leaked oil, coolant seems to ooze out
everywhere, and after all it still has exhaust valves to fail. I've
just discovered a pinhole exhaust pipe leak that was burning the
paint on the engine mount, it's not that far from fuel and oil
lines. Just what I need, an in-flight fire:( I think my old Subaru
E$A 81 is better engineered and cheaper.

John Evans
(Heretic)

I think you are going to have to make your own.
Tracy's system works well for a two rotor but a one rotor
fires half as often. Tracy's system allows the engine to idle
down to 1500 RPM. That should be your target idle RPM.

I would use his general design and increase the diameter
of the rubber bushings and use a lower Durometer rubber.
Silicone rubber is called for as it has a higher heat tolerance.
A lot of heat will be going into the rubber.
You can make the bushings out of silicone rubber sheet
from McMaster. Allow a bit of expansion room.

There may also be an off the shelf off road rear wheel
motor cycle part that might work.

The Centeflex is too stiff and they don't make a much softer
one.

Paul Lamar

Don't forget that the rotors still have longer time per cycle than a
piston
engine. 270* instead of 180* that helps torsional vibration.

Check Chrysler products for a damper similar to the one in
Attachement 4. It
is used on the drive shaft instead of a U-joint. Chrysler 300, Jeep
Gr. Cherokee.

Dale Davies

Generally that type is too stiff. The have a resonant frequency around
2000 RPM. A two rotor is firing 4000 times per minute or
66 CPS or 66 Hertz in the metric system. The one rotor would
be half that.

Paul Lamar


So is Richard using the Hirth "doughnut"?

John Evans

Yes I think so.

You could pack it in dry ice and drill six 1/2 inch holes
to soften it up.

Paul Lamar

There are a lot of doughnuts available (bolt patterns, circle diameter)
various vehicles (BMW, mercedes) and engineered (lord...) versions for
industrial equipment.Look up "guibo" or "flex disc".
I've heard many of the cheap automotive knock-offs do not last as long.
Many of the automotive versions are fiber reinforced and quite stiff.
With some googling you should find catalogs from manufacturers such as
"Lemforder" with a selection of off the shelf sizes, materials and
durometers.

For all of the weight freaks out there.
I looked at additional weight savings as part of a custom redrive using
a flex disc or bushings bolted to the rear counterweight with a button
race clutch /ring gear and starter.  I never found a perfect match that
did not require some customization.
If someone is doing custom rotors, this might be the opportunity to
redesign the rear counterweight for a different bolt size/pattern with a
more secure through nut and bolt configuration.
You could probably save another 5+ pounds in the process.  Even more
with one of those machined adapter plates, a custom casting or an
adapted S5 auto transmission bellhousing.
BTW, those flexplate bolts can back off.  The amount of energy is
impressive if they decide to depart and go airborne.  Lock wire or
Loctite them.

Cheers
Cary

Lemforder wants to sell a car part number with no specs
on the rubber coupling. We need input on stiffness and max torque.
Same thing for guibo which apparently is the BMW coupling.
Same thing for flex disc. They just want to sell you a new one.

We need OEM type data. Perhaps you can find it and send
a link.

We can get that type of data from Centaflex.
http://www.centa.info/?show=downloads&c=mx#
<http://www.centa.info/?show=downloads&c=mx#>

There might be something in there somewhere but it is
wearing me out converting metric to English :)

CENTAFLEX design X

We need about 300 newton meters or about 200 foot
pounds. That indicates a size 16 which has a max RPM
of only 6000. That is the size Rotomax used and it is
no where near soft enough or  fast enough for a
p-port one rotor. (7500 RPM)

Give them a try. They are the world leader with
a dozen variations


Paul Lamar


Paul

This idea will require a little engineering but may save a little weight.
Is there an advantage to putting the flex part on the e-shaft and
coupling that to a (lighter) flywheel attached to the PSRU input shaft?

Dan F

Fly wheels always help but unfortunate they weigh.

The prop acts like a huge flywheel on the end of a shaft and
that becomes part of the problem.

Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.