Subject: torsional vibration
From: Rotary Engine
Date: 1/17/2011, 1:13 PM
To: AAA Put this in the To box


  Now that torsional vibration is being discussed let's get back to the
  single rotor version. Does anyone know what would be a satisfactory
  torsional vibration damper for these as they don't have the overlapping
  power pulses from the other rotor to smooth things out i.e. how much
  flywheel do they need?

  I note that Richard Sohn uses a Hirth reduction box on his - I think
  they use a rubber dough nut like the Rotax 2 stroke reductions?

  Are the rubber isolators used by Tracey suitable for the frequencies
  of a single rotor, let alone the increased amplitude with no
  overlapping
  power strokes?

  It would be nice if the collected wisdom on single rotors was available
  in one place, after all about 100 to 120 HP (Rotax 912 to 914
  territory) is commonly needed for very light aircraft. I must admit
  I'm not all that impressed with my 912, it only has 29.9 hours on it,
  the fuel pump failed - leaked oil, coolant seems to ooze out
  everywhere, and after all it still has exhaust valves to fail. I've
  just discovered a pinhole exhaust pipe leak that was burning the
  paint on the engine mount, it's not that far from fuel and oil
  lines. Just what I need, an in-flight fire:( I think my old Subaru
  E$A 81 is better engineered and cheaper.

  John Evans
  (Heretic)

  I think you are going to have to make your own.
  Tracy's system works well for a two rotor but a one rotor
  fires half as often. Tracy's system allows the engine to idle
  down to 1500 RPM. That should be your target idle RPM.

  I would use his general design and increase the diameter
  of the rubber bushings and use a lower Durometer rubber.
  Silicone rubber is called for as it has a higher heat tolerance.
  A lot of heat will be going into the rubber.
  You can make the bushings out of silicone rubber sheet
  from McMaster. Allow a bit of expansion room.

  There may also be an off the shelf off road rear wheel
  motor cycle part that might work.

  The Centeflex is too stiff and they don't make a much softer
  one.

  Paul Lamar

  Don't forget that the rotors still have longer time per cycle than a
  piston
  engine. 270* instead of 180* that helps torsional vibration.

  Check Chrysler products for a damper similar to the one in
  Attachement 4. It
  is used on the drive shaft instead of a U-joint. Chrysler 300, Jeep
  Gr. Cherokee.

  Dale Davies

  Generally that type is too stiff. The have a resonant frequency around
  2000 RPM. A two rotor is firing 4000 times per minute or
  66 CPS or 66 Hertz in the metric system. The one rotor would
  be half that.

  Paul Lamar


  So is Richard using the Hirth "doughnut"?

  John Evans

  Yes I think so.

  You could pack it in dry ice and drill six 1/2 inch holes
  to soften it up.

  Paul Lamar

 There are a lot of doughnuts available (bolt patterns, circle diameter)
 various vehicles (BMW, mercedes) and engineered (lord...) versions for
 industrial equipment.Look up "guibo" or "flex disc".
 I've heard many of the cheap automotive knock-offs do not last as long.
 Many of the automotive versions are fiber reinforced and quite stiff.
 With some googling you should find catalogs from manufacturers such as
 "Lemforder" with a selection of off the shelf sizes, materials and
 durometers.

 For all of the weight freaks out there.
 I looked at additional weight savings as part of a custom redrive using
 a flex disc or bushings bolted to the rear counterweight with a button
 race clutch /ring gear and starter. I never found a perfect match that
 did not require some customization.
 If someone is doing custom rotors, this might be the opportunity to
 redesign the rear counterweight for a different bolt size/pattern with a
 more secure through nut and bolt configuration.
 You could probably save another 5+ pounds in the process. Even more
 with one of those machined adapter plates, a custom casting or an
 adapted S5 auto transmission bellhousing.
 BTW, those flexplate bolts can back off. The amount of energy is
 impressive if they decide to depart and go airborne. Lock wire or
 Loctite them.

 Cheers
 Cary

 Lemforder wants to sell a car part number with no specs
 on the rubber coupling. We need input on stiffness and max torque.
 Same thing for guibo which apparently is the BMW coupling.
 Same thing for flex disc. They just want to sell you a new one.

 We need OEM type data. Perhaps you can find it and send
 a link.

 We can get that type of data from Centaflex.
 http://www.centa.info/?show=downloads&c=mx#

 There might be something in there somewhere but it is
 wearing me out converting metric to English :)

 CENTAFLEX design X

 We need about 300 newton meters or about 200 foot
 pounds. That indicates a size 16 which has a max RPM
 of only 6000. That is the size Rotomax used and it is
 no where near soft enough or fast enough for a
 p-port one rotor. (7500 RPM)

 Give them a try. They are the world leader with
 a dozen variations

 Paul Lamar

 Hey Paul;
 I don't mean to sound like a jerk with my quick, formal emails. I found
 charts from Lemforder and other OEMs many years ago - heck if I could
 re-find the info before I sent the email - if I find it again, I'll
 forward it.
 There is virtually no engineering data to be had with ANY automotive
 product.
 Someone could experimentally measure most of it; or
 call Lemforder's engineering departments; or
 order elastomers with known physicals from someone such as
 McMasterCarr; or
 use the pre-engineered industrial parts such as the Centaflex, Lord
 LCD/LCR.
 It seems there is no free lunch.
 Cheers
 Cary

 I did not get that impression. It was late and I was tired
 and did not feel like wading through all that metric stuff
 and translating it all to the english system. Too bad there
 is not a physics computer program around that will read a bunch
 of metric data tables and translate them to the english system.

 Anybody want to have a go at this one?

 Paul Lamar

There are plenty of web sites that can do that for you. If that's not
alright with you just write up the specifications for the program you
have in mind and I will build you a nice menu driven command line
program that you can use on your Linux machine.

Mark LaPierre

That will be a good trick. Input is a pdf file.
Here is a screen capture that could be OCR ed.

It might be done by loading it into a spread sheet.

It is quit tedious using a conversion web site but here
is one I use all the time.

http://www.onlineconversion.com

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.