Subject: Improved Renesis Water Pump
From: Rotary Engine
Date: 1/19/2011, 5:07 PM
To: AAA Put this in the To box

   Paul,

   With an eye toward improving the cooling on my p-port 20B, I ordered one
   of these custom water pumps from Mazmart yesterday. They claim it will
   not cavitate up to 10,000 rpm. So, it should be well within the
   operating limits at 6000 - 7000 rpm. This looks even nicer than the 20B
   impeller.

   Mark

   P.S. They will give a discount for group buys of 10 or more.

   ------------------------------------------------------------
   Great news Mark. I assume this is the RX8 version. Do they have
   a 13B version. http://www.mazmart.com/

   Do you have the exact link? Is it a new RX8 part or a used
   RX8 part. I can't find it on the site?

   When the continuous power goes up the heating requirements
   on the rotor housings also go up. It is a good idea to install
   a rotor housing thermocouple. Similar to a cylinder head
   temperature gage. You want to keep the temperature of the aluminum
   under 500 F.

   The old 13B water pump had a better rotor than the
   new RX8 water pump.

   Is your engine back together? Let us know
   what the rotor housing thermocouple says.

   Paul Lamar

   P.S.

   I forgot to mention Mark is running an RX8 water pump on a
   3 rotor p-port so the cooling requirements are 150%
   of that of an RX8.

   Paul Lamar


   Hi Paul,

   I have had a reply from Mazmart about the improved water pump.
   The price will be $240 for orders of 4 or more.
   What I need is 3 other interested guys to come forward
   So we can get an order together.

   Chris in NZ

   That is a ridiculous price for a 3 inch diameter impeller.
   I think you could walk into any NC mill shop in NZ and have just one
   made for that price.

   Software has improved to the point that all you have
   to do is a drawing and software writes the NC mill program.

   Actually all you have to do is buy a good replacement RX7 pump cartridge
   for $30, press the impeller off. Throw away the rest of the RX7 pump
   cart cartridge and install the RX7 impeller on the RX8 pump.

   If you are using an RX8 pump on a 13B don't! Use a GMB aluminumn
   cartridge pump instead.

   Paul Lamar

   Hi Paul,

   Thanks for that , I?ll give it a go, could be a bitch getting the old
   impeller off though, what sort of puller should I use ?
   While I was taking off the apex lube pump I realized that
   the drive for it would make a good way to make a engine
   driven fuel pump, has anybody tried this ?
   It would be relatively easy to make up a little camshaft
   In a housing block and bolt a car pump on to it.

   Chris in NZ.

   You could machine a steel disk on a lathe that
   will slip under the edge of the impeller and saw it
   in half with a band saw. Then put the works in a ten ton
   press and press the impeller off. Another way is chuck the pulley
   end of shaft in a lathe and cut the impeller off on the
   other side of the pump body. Companies rebuild Mazda
   rotary water pump cartridge all the time with tricks like
   this. The bearings and seals become shot and must be replaced.
   That means getting the shaft out some how of course.

   BTW here are some pictures of the aluminum GMB pump
   cartridge. GMB makes a new cartridge for the 3 rotor water pump
   as well I think. Getting one might be a problem as our man
   in Japan is on vacation for another month or so.

   Paul Lamar

  Paul,

  With an eye to single rotors could you comment on water pump selection.
  With
  a smaller engine and less heat to dissipate, could a smaller pump be
  utilized ? Does a smaller practical existing pump spring to mind ? Could
  the
  existing pump simply be slowed ? Would there be an efficiency loss to
  slowing the pump or is it just so small as to make it not worth bothering
  about ? If the stock pump is 3-5 hp that would be perhaps 6% of the power
  output of a single rotor. If we can halve the pump usage we have
  increased
  the power out put by 3%.

  John

  I would take the easy way out and use the GMB pump at the stock speed.

  You cannot have too much water flowing through the block.

  With 120 HP to work with a couple HP here and there matters not.
  Picking the right prop will have more effect.

  Have you emailed Daryl Drummond <fastrotary@mac.com
  <mailto:fastrotary@mac.com ?

  If enough people that want 1 rotors email him he will
  be encouraged to get into the biz. He is one of the finest
  rotary engine builders in the world. Mazda Corp choice
  for building spec engines.

  Paul Lamar

  Chris,

  It seems as if they are offering a $25 discount. That's good as far as
  it goes. However, if the pumps must be shipped to a single place and
  then reshipped to the individual, the savings goes way down and it might
  not be worth it. If they can drop ship to the individuals, if ordered
  together, that's a pump of a different color.

  Any info on this?

  I am still interested if the above can be solved

  Rich


Paul,   I know nothing about rotaries but water pumps used to do them
nearly every day, 30/40 years ago. If we had a water pump that would not
come apart without pressing on the shaft (where we had to save the
bearing) we used to hacksaw thru the impeller near the hub in opposite
sides and then partly drill the hub, near the to the shaft then support
the shaft and apply a chisel and cut partway and the hub just slides
off. modern pumps usually have the seal not running on the back of the
impeller so if new one can just press on the new  impeller to the
correct clearance from the body of the pump. i think Paul's description
is "shade tree mechanic".
     John Burey.

Here is a nice drawing on the guts of a modern pump.

While you are at it... it would be a good idea to replace the shaft
seal with something better. Car parts are built down to the
last penny so spend $40 bucks on a better seal. Some replacement
water pump cartridge cost about $40 bucks over all so you can imagine
the quality of the stock seals. You can buy these in bearing supply
companies all over the world.

I have one of these oscillating saws and it works great on steel.
Ideal for removing the impeller. Makes removing the impeller a
piece of cake. No need for a chisel.

Paul Lamar

Hi Guys,

Thanks for all the good advice on how to dismantle the water pump.
My problem is I haven’t been able to find an impeller here in NZ
they all come pre-assembled (expensive).Where would be the
best source in the states to get one.

Chris in NZ

You guys have Ebay over there?
http://shop.ebay.com/i.html?_kw=RX7&_kw=Water&_kw=pump

Take the good old cast iron impeller off and through the rest away.


Paul Lamar
-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.