Subject: Improved Renesis Water Pump
From: Rotary Engine
Date: 1/20/2011, 3:40 PM
To: AAA Put this in the To box


Paul,

With an eye toward improving the cooling on my p-port 20B, I
 ordered one
of these custom water pumps from Mazmart yesterday. They claim it will
not cavitate up to 10,000 rpm. So, it should be well within the
operating limits at 6000 - 7000 rpm. This looks even nicer than the 20B
impeller.

Mark

P.S. They will give a discount for group buys of 10 or more.

------------------------------------------------------------
Great news Mark. I assume this is the RX8 version. Do they have
a 13B version. http://www.mazmart.com/

Do you have the exact link? Is it a new RX8 part or a used
RX8 part. I can't find it on the site?

When the continuous power goes up the heating requirements
on the rotor housings also go up. It is a good idea to install
a rotor housing thermocouple. Similar to a cylinder head
temperature gage. You want to keep the temperature of the aluminum
under 500 F.

The old 13B water pump had a better rotor than the
new RX8 water pump.

Is your engine back together? Let us know
what the rotor housing thermocouple says.

Paul Lamar

P.S.

I forgot to mention Mark is running an RX8 water pump on a
3 rotor p-port so the cooling requirements are 150%
of that of an RX8.

Paul Lamar


Hi Paul,

I have had a reply from Mazmart about the improved water pump.
The price will be $240 for orders of 4 or more.
What I need is 3 other interested guys to come forward
So we can get an order together.

Chris in NZ

That is a ridiculous price for a 3 inch diameter impeller.
I think you could walk into any NC mill shop in NZ and have just one
made for that price.

Software has improved to the point that all you have
to do is a drawing and software writes the NC mill program.

Actually all you have to do is buy a good replacement RX7 pump
 cartridge
for $30, press the impeller off. Throw away the rest of the RX7 pump
cart cartridge and install the RX7 impeller on the RX8 pump.

If you are using an RX8 pump on a 13B don't! Use a GMB aluminumn
cartridge pump instead.

Paul Lamar

Hi Paul,

Thanks for that , I?ll give it a go, could be a bitch getting the old
impeller off though, what sort of puller should I use ?
While I was taking off the apex lube pump I realized that
the drive for it would make a good way to make a engine
driven fuel pump, has anybody tried this ?
It would be relatively easy to make up a little camshaft
In a housing block and bolt a car pump on to it.

Chris in NZ.

You could machine a steel disk on a lathe that
will slip under the edge of the impeller and saw it
in half with a band saw. Then put the works in a ten ton
press and press the impeller off. Another way is chuck the pulley
end of shaft in a lathe and cut the impeller off on the
other side of the pump body. Companies rebuild Mazda
rotary water pump cartridge all the time with tricks like
this. The bearings and seals become shot and must be replaced.
That means getting the shaft out some how of course.

BTW here are some pictures of the aluminum GMB pump
cartridge. GMB makes a new cartridge for the 3 rotor water pump
as well I think. Getting one might be a problem as our man
in Japan is on vacation for another month or so.

Paul Lamar

 Paul,

 With an eye to single rotors could you comment on water pump selection.
 With
 a smaller engine and less heat to dissipate, could a smaller pump be
 utilized ? Does a smaller practical existing pump spring to mind ?
Could
 the
 existing pump simply be slowed ? Would there be an efficiency loss to
 slowing the pump or is it just so small as to make it not worth
 bothering
 about ? If the stock pump is 3-5 hp that would be perhaps 6% of the
 power
 output of a single rotor. If we can halve the pump usage we have
 increased
 the power out put by 3%.

 John

 I would take the easy way out and use the GMB pump at the stock speed.

 You cannot have too much water flowing through the block.

 With 120 HP to work with a couple HP here and there matters not.
 Picking the right prop will have more effect.

 Have you emailed Daryl Drummond <fastrotary@mac.com
<mailto:fastrotary@mac.com>
<mailto:fastrotary@mac.com <mailto:fastrotary@mac.com>>
 <mailto:fastrotary@mac.com <mailto:fastrotary@mac.com>
<mailto:fastrotary@mac.com <mailto:fastrotary@mac.com>>>
 <mailto:fastrotary@mac.com <mailto:fastrotary@mac.com>
<mailto:fastrotary@mac.com <mailto:fastrotary@mac.com>>

<mailto:fastrotary@mac.com <mailto:fastrotary@mac.com>
<mailto:fastrotary@mac.com <mailto:fastrotary@mac.com>>> ?


 If enough people that want 1 rotors email him he will
 be encouraged to get into the biz. He is one of the finest
 rotary engine builders in the world. Mazda Corp choice
 for building spec engines.

 Paul Lamar

 Chris,

 It seems as if they are offering a $25 discount. That's good as far as
 it goes. However, if the pumps must be shipped to a single place and
 then reshipped to the individual, the savings goes way down and it
might
 not be worth it. If they can drop ship to the individuals, if ordered
 together, that's a pump of a different color.

 Any info on this?

 I am still interested if the above can be solved

 Rich


 Paul,I know nothing about rotaries but water pumps used to do them
 nearly every day, 30/40 years ago. If we had a water pump that
would not
 come apart without pressing on the shaft (where we had to save the
 bearing) we used to hacksaw thru the impeller near the hub in opposite
 sides and then partly drill the hub, near the to the shaft then support
 the shaft and apply a chisel and cut partway and the hub just slides
 off. modern pumps usually have the seal not running on the back of the
 impeller so if new one can just press on the new  impeller to the
 correct clearance from the body of the pump. i think Paul's description
 is "shade tree mechanic".
 John Burey.

 Here is a nice drawing on the guts of a modern pump.

 While you are at it... it would be a good idea to replace the shaft
 seal with something better. Car parts are built down to the
 last penny so spend $40 bucks on a better seal. Some replacement
 water pump cartridge cost about $40 bucks over all so you can imagine
 the quality of the stock seals. You can buy these in bearing supply
 companies all over the world.

 I have one of these oscillating saws and it works great on steel.
 Ideal for removing the impeller. Makes removing the impeller a
 piece of cake. No need for a chisel.

 Paul Lamar

 Hi Guys,

 Thanks for all the good advice on how to dismantle the water pump.
 My problem is I haven?t been able to find an impeller here in NZ
 they all come pre-assembled (expensive).Where would be the
 best source in the states to get one.

 Chris in NZ

 You guys have Ebay over there?
 http://shop.ebay.com/i.html?_kw=RX7&_kw=Water&_kw=pump
<http://shop.ebay.com/i.html?_kw=RX7&_kw=Water&_kw=pump>
<http://shop.ebay.com/i.html?_kw=RX7&_kw=Water&_kw=pump
<http://shop.ebay.com/i.html?_kw=RX7&_kw=Water&_kw=pump>>
Take the good old cast iron impeller off and through the rest away.


 Paul Lamar

 Hi Paul,
 Thanks for the good advice, I will do just that.
 Which of those would recommend ( I?m fairly new to rotaries)
 or are they all much the same.

 Cheers Chris  in NZ.

 The one you want to avoid is the 3rd gen RX7 built in
 the years 1993 to 2004. That had a sheet steel impeller
 that rotated the wrong way. All the rest, except the RX8, had
 a very durable, cast iron, well designed impeller. There is a
 possibility that they won't fit the RX8 water pump housing
 so they may need to be trimmed in a lathe. Trick is to temporally
 assemble them with clay inside to check the clearance.
 Then make the necessary adjustments. If too much clearance
 move the impeller out on the shaft and use a spacer behind
 it. The spacer can be braised to the back side of the
 impeller if necessary.

 I think the MazMart impeller is aluminum and soft enough
 to be damage by minor local cavitation. The 1990 1991 and 1992
 turbo charged RX7 engine pumps might be the best of the lot.


 Paul Lamar


Paul,

The Mazmart impeller is SS.  Should last a long time.

Mark

I am so glad it is not aluminum :)
Did you get one yet?

Here is what water can do to aluminum.
Can anybody tell me what happened here?


Paul Lamar


Hmmm...  I will suppose it was caused by suction cavitation
where the coolant boils violently. Over time and with corrosion
this pulls material off the casting.  Also happens on boat
propellers.

Dan F

Warmer.


Paul Lamar



Probably cavitation caused by collapsed lower radiator hose.

Mark

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.