Subject: Improved Renesis Water Pump
From: Rotary Engine
Date: 1/20/2011, 3:48 PM
To: AAA Put this in the To box



 With an eye toward improving the cooling on my p-port 20B,
 I
 ordered one
 of these custom water pumps from Mazmart yesterday. They
 claim it will
 not cavitate up to 10,000 rpm. So, it should be well
 within the
 operating limits at 6000 - 7000 rpm. This looks even nicer
 than the 20B
 impeller.
 Mark
 P.S. They will give a discount for group buys of 10 or
 more.
 ------------------------------------------------------------
 Great news Mark. I assume this is the RX8 version. Do they
 have
 a 13B version. http://www.mazmart.com/
 Do you have the exact link? Is it a new RX8 part or a
 used
 RX8 part. I can't find it on the site?
 When the continuous power goes up the heating
 requirements
 on the rotor housings also go up. It is a good idea to
 install
 a rotor housing thermocouple. Similar to a cylinder head
 temperature gage. You want to keep the temperature of the
 aluminum
 under 500 F.
 The old 13B water pump had a better rotor than the
 new RX8 water pump.
 Is your engine back together? Let us know
 what the rotor housing thermocouple says.
 Paul Lamar
 P.S.
 I forgot to mention Mark is running an RX8 water pump on
 a
 3 rotor p-port so the cooling requirements are 150%
 of that of an RX8.
 Paul Lamar

 Hi Paul,
 I have had a reply from Mazmart about the improved water
 pump.
 The price will be $240 for orders of 4 or more.
 What I need is 3 other interested guys to come forward
 So we can get an order together.
 Chris in NZ
 That is a ridiculous price for a 3 inch diameter
 impeller.
 I think you could walk into any NC mill shop in NZ and
 have just one
 made for that price.
 Software has improved to the point that all you have
 to do is a drawing and software writes the NC mill
 program.
 Actually all you have to do is buy a good replacement RX7
 pump
 cartridge
 for $30, press the impeller off. Throw away the rest of
 the RX7 pump
 cart cartridge and install the RX7 impeller on the RX8
 pump.
 If you are using an RX8 pump on a 13B don't! Use a GMB
 aluminumn
 cartridge pump instead.
 Paul Lamar
 Hi Paul,
 Thanks for that , I?ll give it a go, could be a bitch
 getting the old
 impeller off though, what sort of puller should I use ?
 While I was taking off the apex lube pump I realized that
 the drive for it would make a good way to make a engine
 driven fuel pump, has anybody tried this ?
 It would be relatively easy to make up a little camshaft
 In a housing block and bolt a car pump on to it.
 Chris in NZ.
 You could machine a steel disk on a lathe that
 will slip under the edge of the impeller and saw it
 in half with a band saw. Then put the works in a ten ton
 press and press the impeller off. Another way is chuck the
 pulley
 end of shaft in a lathe and cut the impeller off on the
 other side of the pump body. Companies rebuild Mazda
 rotary water pump cartridge all the time with tricks like
 this. The bearings and seals become shot and must be
 replaced.
 That means getting the shaft out some how of course.
 BTW here are some pictures of the aluminum GMB pump
 cartridge. GMB makes a new cartridge for the 3 rotor water
 pump
 as well I think. Getting one might be a problem as our
 man
 in Japan is on vacation for another month or so.
 Paul Lamar

 Paul,

 With an eye to single rotors could you comment on
 water pump selection.
 With
 a smaller engine and less heat to dissipate, could a
 smaller pump be
 utilized ? Does a smaller practical existing pump
 spring to mind ? Could
 the
 existing pump simply be slowed ? Would there be an
 efficiency loss to
 slowing the pump or is it just so small as to make
 it not worth
 bothering
 about ? If the stock pump is 3-5 hp that would be
 perhaps 6% of the
 power
 output of a single rotor. If we can halve the pump
 usage we have
 increased
 the power out put by 3%.

 John

 I would take the easy way out and use the GMB pump
 at the stock speed.

 You cannot have too much water flowing through the
 block.

 With 120 HP to work with a couple HP here and there
 matters not.
 Picking the right prop will have more effect.

 Have you emailed Daryl Drummond <fastrotary@mac.com
<mailto:fastrotary@mac.com>
 <mailto:fastrotary@mac.com <mailto:fastrotary@mac.com>
 <mailto:fastrotary@mac.com <mailto:fastrotary@mac.com>
 <mailto:fastrotary@mac.com <mailto:fastrotary@mac.com>
 ?

 If enough people that want 1 rotors email him he
 will
 be encouraged to get into the biz. He is one of the
 finest
 rotary engine builders in the world. Mazda Corp
 choice
 for building spec engines.

 Paul Lamar

 Chris,

 It seems as if they are offering a $25 discount.
 That's good as far as
 it goes. However, if the pumps must be shipped to a
 single place and
 then reshipped to the individual, the savings goes
 way down and it might
 not be worth it. If they can drop ship to the
 individuals, if ordered
 together, that's a pump of a different color.

 Any info on this?

 I am still interested if the above can be solved

 Rich


 Paul,I know nothing about rotaries but water pumps
 used to do them
 nearly every day, 30/40 years ago. If we had a water
 pump that would not
 come apart without pressing on the shaft (where we
 had to save the
 bearing) we used to hacksaw thru the impeller near
 the hub in opposite
 sides and then partly drill the hub, near the to the
 shaft then support
 the shaft and apply a chisel and cut partway and the
 hub just slides
 off. modern pumps usually have the seal not running
 on the back of the
 impeller so if new one can just press on the
 new  impeller to the
 correct clearance from the body of the pump. i think
 Paul's description
 is "shade tree mechanic".
 John Burey.

 Here is a nice drawing on the guts of a modern
 pump.

 While you are at it... it would be a good idea to
 replace the shaft
 seal with something better. Car parts are built down
 to the
 last penny so spend $40 bucks on a better seal. Some
 replacement
 water pump cartridge cost about $40 bucks over all
 so you can imagine
 the quality of the stock seals. You can buy these in
 bearing supply
 companies all over the world.

 I have one of these oscillating saws and it works
 great on steel.
 Ideal for removing the impeller. Makes removing the
 impeller a
 piece of cake. No need for a chisel.

 Paul Lamar

 Hi Guys,

 Thanks for all the good advice on how to dismantle
 the water pump.
 My problem is I haven?t been able to find an
 impeller here in NZ
 they all come pre-assembled (expensive).Where would
 be the
 best source in the states to get one.

 Chris in NZ

 You guys have Ebay over there?
 http://shop.ebay.com/i.html?_kw=RX7&_kw=Water&_kw=pump
<http://shop.ebay.com/i.html?_kw=RX7&_kw=Water&_kw=pump>
 Take the good old cast iron impeller off and through the
 rest away.


 Paul Lamar

 Hi Paul,
 Thanks for the good advice, I will do just that.
 Which of those would recommend ( I?m fairly new to
 rotaries)
 or are they all much the same.

 Cheers Chris  in NZ.

 The one you want to avoid is the 3rd gen RX7 built
 in
 the years 1993 to 2004. That had a sheet steel
 impeller
 that rotated the wrong way. All the rest, except the
 RX8, had
 a very durable, cast iron, well designed impeller.
 There is a
 possibility that they won't fit the RX8 water pump
 housing
 so they may need to be trimmed in a lathe. Trick is
 to temporally
 assemble them with clay inside to check the
 clearance.
 Then make the necessary adjustments. If too much
 clearance
 move the impeller out on the shaft and use a spacer
 behind
 it. The spacer can be braised to the back side of
 the
 impeller if necessary.

 I think the MazMart impeller is aluminum and soft
 enough
 to be damage by minor local cavitation. The 1990
 1991 and 1992
 turbo charged RX7 engine pumps might be the best of
 the lot.


 Paul Lamar

 Paul,
 The Mazmart impeller is SS.  Should last a long
 time.
 Mark
 I am so glad it is not aluminum :)
 Did you get one yet?
 Here is what water can do to aluminum.
 Can anybody tell me what happened here?
 Paul Lamar
 Cavitation  --- erosion  I had this happen to my Jeep Grand
 Cherokee when the dealer replaced the water pump and did
 not bleed all
 the air.

 Jim Brewer
 I don't think so.
 Any other ideas?

 Paul Lamar


Electrolysis.

Robert

Possibly. Note the damage stops on a straight line parallel
with the ground. I think it was run on low coolant level.



Paul Lamar


Paul,  Low on coolant is a good fit, but a faulty thermostat not
allowing full flow is my bet. The water temp would be higher from the
mechanical agitation of the non flowing water putting 3-5 hp into the
coolant with no where  for the energy to go. The higher temp results in
steam at the lower pressure  around the pump inlet and steam erosion.
The unerroded part is likely where what water actually flowing thru the
pump entered the impeller. In industry we use a small valve in parallel
to very large valves when partial flow is required. Operating the large
valve mostly closed causes valve wear.

george grimes

Paul Lamar

-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.