With an eye toward improving the cooling on my p-port 20B,
I
ordered one
of these custom water pumps from Mazmart yesterday. They
claim it will
not cavitate up to 10,000 rpm. So, it should be well
within the
operating limits at 6000 - 7000 rpm. This looks even nicer
than the 20B
impeller.
Mark
P.S. They will give a discount for group buys of 10 or
more.
------------------------------------------------------------
Great news Mark. I assume this is the RX8 version. Do they
have
a 13B version.
http://www.mazmart.com/
Do you have the exact link? Is it a new RX8 part or a
used
RX8 part. I can't find it on the site?
When the continuous power goes up the heating
requirements
on the rotor housings also go up. It is a good idea to
install
a rotor housing thermocouple. Similar to a cylinder head
temperature gage. You want to keep the temperature of the
aluminum
under 500 F.
The old 13B water pump had a better rotor than the
new RX8 water pump.
Is your engine back together? Let us know
what the rotor housing thermocouple says.
Paul Lamar
P.S.
I forgot to mention Mark is running an RX8 water pump on
a 3 rotor p-port so the cooling requirements are 150%
of that of an RX8.
Paul Lamar
Hi Paul,
I have had a reply from Mazmart about the improved water
pump.
The price will be $240 for orders of 4 or more.
What I need is 3 other interested guys to come forward
So we can get an order together.
Chris in NZ
That is a ridiculous price for a 3 inch diameter
impeller.
I think you could walk into any NC mill shop in NZ and
have just one
made for that price.
Software has improved to the point that all you have
to do is a drawing and software writes the NC mill
program.
Actually all you have to do is buy a good replacement RX7
pump
cartridge
for $30, press the impeller off. Throw away the rest of
the RX7 pump
cart cartridge and install the RX7 impeller on the RX8
pump.
If you are using an RX8 pump on a 13B don't! Use a GMB
aluminumn
cartridge pump instead.
Paul Lamar
Hi Paul,
Thanks for that , I?ll give it a go, could be a bitch
getting the old
impeller off though, what sort of puller should I use ?
While I was taking off the apex lube pump I realized that
the drive for it would make a good way to make a engine
driven fuel pump, has anybody tried this ?
It would be relatively easy to make up a little camshaft
In a housing block and bolt a car pump on to it.
Chris in NZ.
You could machine a steel disk on a lathe that
will slip under the edge of the impeller and saw it
in half with a band saw. Then put the works in a ten ton
press and press the impeller off. Another way is chuck the
pulley
end of shaft in a lathe and cut the impeller off on the
other side of the pump body. Companies rebuild Mazda
rotary water pump cartridge all the time with tricks like
this. The bearings and seals become shot and must be
replaced.
That means getting the shaft out some how of course.
BTW here are some pictures of the aluminum GMB pump
cartridge. GMB makes a new cartridge for the 3 rotor water
pump
as well I think. Getting one might be a problem as our
man
in Japan is on vacation for another month or so.
Paul Lamar
Paul,
With an eye to single rotors could you comment on
water pump selection.
With
a smaller engine and less heat to dissipate, could a
smaller pump be
utilized ? Does a smaller practical existing pump
spring to mind ? Could
the
existing pump simply be slowed ? Would there be an
efficiency loss to
slowing the pump or is it just so small as to make
it not worth
bothering
about ? If the stock pump is 3-5 hp that would be
perhaps 6% of the
power
output of a single rotor. If we can halve the pump
usage we have
increased
the power out put by 3%.
John
I would take the easy way out and use the GMB pump
at the stock speed.
You cannot have too much water flowing through the
block.
With 120 HP to work with a couple HP here and there
matters not.
Picking the right prop will have more effect.
Have you emailed Daryl Drummond <
fastrotary@mac.com
mailto:fastrotary@mac.com
If enough people that want 1 rotors email him he
will
be encouraged to get into the biz. He is one of the
finest
rotary engine builders in the world. Mazda Corp
choice
for building spec engines.
Paul Lamar
Chris,
It seems as if they are offering a $25 discount.
That's good as far as
it goes. However, if the pumps must be shipped to a
single place and
then reshipped to the individual, the savings goes
way down and it might
not be worth it. If they can drop ship to the
individuals, if ordered
together, that's a pump of a different color.
Any info on this?
I am still interested if the above can be solved
Rich
Paul,I know nothing about rotaries but water pumps
used to do them
nearly every day, 30/40 years ago. If we had a water
pump that would not
come apart without pressing on the shaft (where we
had to save the
bearing) we used to hacksaw thru the impeller near
the hub in opposite
sides and then partly drill the hub, near the to the
shaft then support
the shaft and apply a chisel and cut partway and the
hub just slides
off. modern pumps usually have the seal not running
on the back of the
impeller so if new one can just press on the
new impeller to the
correct clearance from the body of the pump. i think
Paul's description
is "shade tree mechanic".
John Burey.
Here is a nice drawing on the guts of a modern
pump.
While you are at it... it would be a good idea to
replace the shaft
seal with something better. Car parts are built down
to the
last penny so spend $40 bucks on a better seal. Some
replacement
water pump cartridge cost about $40 bucks over all
so you can imagine
the quality of the stock seals. You can buy these in
bearing supply
companies all over the world.
I have one of these oscillating saws and it works
great on steel.
Ideal for removing the impeller. Makes removing the
impeller a
piece of cake. No need for a chisel.
Paul Lamar
Hi Guys,
Thanks for all the good advice on how to dismantle
the water pump.
My problem is I haven?t been able to find an
impeller here in NZ
they all come pre-assembled (expensive).Where would
be the
best source in the states to get one.
Chris in NZ
You guys have Ebay over there?
http://shop.ebay.com/i.html?_kw=RX7&_kw=Water&_kw=pump
Take the good old cast iron impeller off and through the
rest away.
Paul Lamar
Hi Paul,
Thanks for the good advice, I will do just that.
Which of those would recommend ( I?m fairly new to
rotaries)
or are they all much the same.
Cheers Chris in NZ.
The one you want to avoid is the 3rd gen RX7 built
in
the years 1993 to 2004. That had a sheet steel
impeller
that rotated the wrong way. All the rest, except the
RX8, had
a very durable, cast iron, well designed impeller.
There is a
possibility that they won't fit the RX8 water pump
housing
so they may need to be trimmed in a lathe. Trick is
to temporally
assemble them with clay inside to check the
clearance.
Then make the necessary adjustments. If too much
clearance
move the impeller out on the shaft and use a spacer
behind
it. The spacer can be braised to the back side of
the
impeller if necessary.
I think the MazMart impeller is aluminum and soft
enough
to be damage by minor local cavitation. The 1990
1991 and 1992
turbo charged RX7 engine pumps might be the best of
the lot.
Paul Lamar
Paul,
The Mazmart impeller is SS. Should last a long
time.
Mark
I am so glad it is not aluminum :)
Did you get one yet?
Here is what water can do to aluminum.
Can anybody tell me what happened here?
Paul Lamar
Cavitation --- erosion I had this happen to my Jeep Grand
Cherokee when the dealer replaced the water pump and did
not bleed all the air.
Jim Brewer
I don't think so.
Any other ideas?
Paul Lamar
Electrolysis.
Robert
Possibly. Note the damage stops on a straight line parallel
with the ground. I think it was run on low coolant level.
Paul Lamar
Paul, Low on coolant is a good fit, but a faulty thermostat not
allowing full flow is my bet. The water temp would be higher from the
mechanical agitation of the non flowing water putting 3-5 hp into the
coolant with no where for the energy to go. The higher temp results
in steam at the lower pressure around the pump inlet and steam erosion.
The unerroded part is likely where what water actually flowing thru the
pump entered the impeller. In industry we use a small valve in parallel
to very large valves when partial flow is required. Operating the large
valve mostly closed causes valve wear.
george grimes
Paul Lamar
The parallel valve installation is a good deal in the app. you describe
George. I tried to do that on a couple of oil patch installations. Too cheap
to do smart. Also valve erode when controlling a high differential pressure.
Say 1000PSI into a tank at atmospheric pressure. Changed lots of 3/8" and 1/2"
trims on 3 phase separators on the liquid dump valves.
I think Paul may be right as you would think a collapsed hose or faulty
thermostat would let it erode all the way around. I would think that there may
have been some electrolysis at work compounding the trouble. Likely poorly
maintained to the core.
Dale Davies
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.