Subject: RX8 injector connectors wanted. Wiring 3
From: Rotary Engine
Date: 1/20/2011, 9:05 PM
To: AAA Put this in the To box

  I am wiring one of Tracy's computer to an RX8 engine
  and I need four injector connectors. I have given
  up on the coil connectors and will make my own.

  Does anybody know where I can get RX8 injector connectors?

  Paul Lamar


The connectors I used are Nissan units.  They worked on my 20B 550cc
injectors as well as the new DEKA-IV injectors I am currently using.
Try a Maxima or 300-ZX.  They should be available on ebay.

Mark S.


Thanks for the tip Mark.

I have broken the job down to 5 harnesses. Starter alternator
harness, Sensor harness, Injector harness, Coil harness and PCM
harness. Since it is hard to get wires in more than about 4 or five
colors this makes the job much easier.

Tracy calls out 20 gage wire for most things but it is a bit
hard to work with. I found a roll of 16 gage speaker wire
with four color coded wires in a white vinyl jacket 100 feet
for $30. I'll use this for coil and injector harnesses. For
the low current PCM harness I am using  an old centronics
printer cable.

Since I am using the the terminal strip break outs
for the D sub min connectors on the EC2 and PCM  It cuts the
job down to one or two days for the whole thing.
It is also a lot neater and easier to trouble shoot.

Paul Lamar

I realize a lot of you don't have extensive electronic technician
training. Just one more stumbling block to installing a rotary.

Help is on the way. I'll document what I do and eventually it will
make it to the web site.

Here is what the top of the engine looks like with the sensor
harness in place. Note the two tie wraps around the split harness
when a wire is brought out for a sensor.

I found some old cheap RS232 cables with DB 25 D sub min connectors
on both ends. 25 colored wires. These can be found up to 10 feet long. We need
only 11 wires for the PCM to the EC2 harness. I cut off the molded
connectors and threw them away. There are two ways to implement the
EC2 to the PCM harness. You can pick out just the solid colored wires
and pull out and throw the rest away. Some Wires have solid colors
with narrow strips of a different color. In this case since we only need
11 we can pair them up with the solid colors.

Paul Lamar

These cables are amazing. I discovered a finger nail makes a good
wire stripper for the roughly 26 gage wire in these things.
Talk about quick.. you just grab the wire and it is stripped.
Better job than most wire strippers.

If for some strange reason you come up with a different brand
of wire and you cannot strip it with your finger nail you
will need a good wire stripper. This is one of the best.
Jonard. www.jonard.com OK ST450

The PCM to EC 2 harness is now done. Since I had 25 color coded
wires to work with I doubled them up. For example a solid black
with with a black with white strip. Makes a more robust harness.

I am not entirely happy with this cable as it takes a bit of time
to strip them and twist and solder together. I am thinking of
ordering some color coded cables with just the right number
of 20 gage wires. Cost is $100 minimum so I hope to find out
what kind of PCM cable is required for the EC 3. Color coding
is essential by my way of thinking as it identifies a wire
instantaneously unlike wire labels. You need this when it
comes time to trouble shoot a problem or check your work.

The other thing that needs changing is the EC 2 break out connector.
It needs to be more compact and have some provision for cable
strain relief like the 15 pin PCM break out connector shown here.

I used this one for the EC 2 as I could buy it off the shelf. I'll
design and build one depending on how the EC 3 works out.

These break out boards are great to work with as things
can be fixed or redone lickity split.


BTW Boat stores have 4 wire color coded 18 gage cable
rather than the over kill 4 wire 16 gage speaker cable I have.
It is rather expensive but it is going to give you
a much better job for the coils and injectors.

Paul Lamar


-- 
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2010 All world wide rights reserved.