Nice to have some English data.
Highest RPM rating I have seen so far.
I don't know what they mean when the say mass moment of
inertia.
Is that of the coupling or the mass moment of inertia it
will
drive? Anybody know how to convert Kg per meter squared?
The magnitude of that could tell us if it was just the
coupling.
Paul Lamar
Back cover of Vector Mechanics for Engineers - Dynamics
(Ferdinand Beer
et. al.)
For mass moment of inertia:
1 lb.*ft*s^2 = 1.356 kg*m^2
Chris Cosman
...back to homework...
Thanks Chris. Are you sure? What is "s" ?
Seconds?
Is that the same as this?
Paul Lamar
Mass Moment of Inertia from the book's appendix:
Notice the picture of the 'camshaft'... don't let that
shake your confidence in the math though.
Chris Cosman
I hate to tell you this Chris but did you know you can
solve
any integral calculus problem in Quick BASIC ?
What you do is sum up all the little tiny cubes of mass
AKA "dm"
multiplied by their distance squared from the axis of
interest :)
Of courses you need a good 3D drawing of the lump with
dimensions :)
What this does in 5 minutes gives you all you need to
know
about integral calculus :)
I have never tried it but I think a spread sheet can do
the same
thing.
I had a mental block against integral calculus until this
dawned on me.
Paul Lamar
No need to apologize. It seems to me that if we want
to boost our competitive edge in this country, we should
start teaching students how real engineers solve problems
and less time on gnarly mathematical concepts. I could
be wrong...
The approach you refer to is generally referred to as
Numerical Methods, currently on my course schedule this
semester. I'm using Matlab software, short for Matrix
Laboratory. Handles large data sets well. I'll
spend the next 4 months boiling complex calculus and
differential equations problems into simple mathematical
approaches the computer can iterate to death. Should
be fun, except for the deadlines.
You are right about the spreadsheet approach. We used
to design folded horn loudspeakers and devised a spreadsheet
to iterate the location of each fold and from there, the
location of the baffles. We ended up fitting a 15"
woofer on a 9 foot horn in less than 20 cubic feet. Works well for
movies like "Open Range".
Now I'm off topic - sorry.
Chris Cosman
No worries mate. I agree with you on the arcane math.
Paul Lamar
To Chris Cosman: doesn't your acoustical designing relate to muffler
design? I thought the current mufflers resonate at the lower range of
human hearing where because our sensitivity "Rolls off" at higher and
lower frequencies, therefore it takes a lot more energy for us to hear
the same volume. So translating frequencies means we hear less noise.
Dave James
In my
/opinion/, the relation between loudspeaker design and muffler
design is loose. In an exhaust system, the gas dropping several hundred
degrees in just a few feet is a big variable, never had to worry about
that in my horns. We did build a few transmission line bass cabinets,
basically a long pipe, folded or no, with a speaker on one end, but
those are tuned to one frequency and it's octaves (one octave is a
doubling of frequency), those would be more akin to a muffler.
I'm not sure but I think exhaust system design was and still is largely
an empirical science.Paul would know more.
Chris Cosman
There is a book out on it.
http://www.rotaryeng.net/books10.html
* Scientific Design of Exhaust and Intake Systems. Philip H. Smith
and John C. Morrison Published by Robert Bentley. ISBN 0-8376-0309-9
http://www.rb.com
Paul Lamar
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.