People don't have a clue until you hear an automotive engine
running full chat on a dyno under full load. The load makes
all the difference in the world as to how an engine feels and sounds.
If you are standing next to it your first impulse is to run
like hell as you get the feeling it is a bomb waiting to go off.
Not a real bomb NSA so don't cogitate over this message too
long? :)
Paul Lamar
Ah, the memories of newly rebuilt 400 HP CAT diesel running full out
on it's first dyno run. It does take a bit to get used to. Had one
suck a shop rag out of my hand one time and shredded it through the
turbo with only a slight momentary change in RPM. Confetti out the
exhaust was all that was left.
Brian G
Shop rag good; fingers BAD! Not mine. Detriot engines had the turbo
above the
blower. If you did not have a screen over the inlet and got your
hand too
close it would suck it in. Needless to say the person's day was
ruined, not to
mention probably career.
Dale Davies
Paul,
Some time ago you recommended that somebody obtain
an old 12A to 'practice' on it. Can you recommend the
oldest, cheapest 13B [or 12A if it won't throw me off] that
I can buy just for the purpose of examining and experimenting?
This will not be the prototype engine, but just a 'model'.
I guess it would be helpful if it could be started or fixed
so that it could be started. Thanks again a million.
Gene Kahn
That brings up an interesting point. Mazda has not fundamentally changed
the 13B since 1974. That makes for a lot of rotary engines out
there. Some times you can find them for free. Any of them make
a good aircraft engine when updated with modern materials like
ceramic apex seals and Teflon O-rings. 1989 or after are better
in terms of life as Mazda hardened the end housings and the
phasing gears around that time.
We were given a couple of 12A's for the engine work shop at
Sun n Fun. Both were in near perfect shape. The only difference
is the 13B has wider rotors and rotor housings. I think the
13B is going down in history as the longest running engine
design of all time. Beating the beetle engine and the cast
iron Chev small block. Started with 110 HP and wound up
in the turbo 3rd gen RX7 with 280 HP. NO increase in displacement
or fundamental design. The RX8 engine is fundamentally the same
thing except the exhaust ports were moved to the side and
center housings
Paul Lamar
Gene,
Keep an eye on the auto classifieds for RX 7 with "real engines" like a
small block chevy retro fitted.
I called one and got the complete engine and auto trans for $50.
John
Its a good way to turn an excellent handling RX7 into a pig.
Imagine taking out a 200 pound engine and putting in a 500
pound engine. The front springs would bottom out. Stiffen
the front springs and then something else would fail
in the front suspension like the lower A arms.
The brakes would give up the first time you
tried to slow it going down a hill.
The next thing you would have to change is the rear axle as
the torque out of an RX7 is at most 200 foot pounds. The
Chevy 400 to 500 foot pounds. Of course the stock tires would
be next. Get out the cutting torch and torch the rear wheel
wells. Add new wider wheel wells and wider rear wheels and tires.
What you wind up with is a drag racer. Not a good car to
drive on the street.
If ever there was a good example of unintended consequences
this is it :)
Paul Lamar
Exactly Paul, perhaps my sarcasm was a bit too subtle. I wanted the rotary
cheap so I had to be polite rather than point all this out to the guy. On
top of all the stuff above he put an automatic transmission in it, a sports
car, can you believe it ?
John
--
The Rotary Engine NewsLetter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
Youtube key word PaulLamar2
Copyright 1998-2011 All world wide rights reserved.